Char-Broil GRILL2GO 11401587 user manual

Summary of the content on the page No. 1

Assembly
Guide
Model Numbers:
11401587
Propane cylinder
sold separately.
Allow approximately 10 minutes for assembly.
PROPANE
(English)
42804597 • 01/07/2011

Summary of the content on the page No. 2

2 A, B, Assembly: ASSEMBLY GUIDE CAUTION: For your safety, before operating, Read Product Guide & Outdoor Cooking Guide provided with this grill. *SAFETY First…..Grill components may have sharp edges. Be careful when handling grill parts during assembly. We suggest that you wear a sturdy pair of leather gloves while handling the grill parts. BEFORE You begin assembly of your grill…. 1. Carefully remove all components from the carton. 2. Familiarize yourself with the components an

Summary of the content on the page No. 3

3 Grill Parts Diagram ASSEMBLY GUIDE EE Y A X B J DD C D I E K AA F L BB R G U V Z T O P Q W CC M S H N Key Qty Description Key Qty Description A 1 GRILL LID P 1 HANDLE, F/ LID B 1 COOKING GRATE Q 1 LOGO PLATE C 1 TROUGH R 1 ELECTRODE W/ WIRE D 1 BURNER S 2 SIDE SHELF BUSHINGS E 1 INNER REFLECTOR T 1 IGNITOR MOUNTING BRACKET F 1 FIREBOX BOTTOM U 1 IGNITOR HEAT SHIELD G 1 GRILL STAND V 1 GRILL HEAD MOUNTING BRACKET H 1 FASCIA, F/ GRILL STAND W 1 GRILL HEAD PULL HANDLE I 1 MATCH HOLDER X 1 HEAT

Summary of the content on the page No. 4

4 ASSEMBLY GUIDE GRILL Assembly Part Qty Fasteners A1– Handle 1 A2– Heat Sheld 1 #10x24x5/8” Hinge Pin Hitch Pin #8 Fiber Washer Machine Screw (Qty. 2) (Qty. 2) (Qty. 4) (Qty. 4) Step 1: Choose a location suitable for assembling your grill. Carefully cut the carton open and use it as a pad to prevent scratching or damaging your grill. Next, verify that you have all of your parts. Assemble the Handle and Heat Shield as shown using 4 #8 Fiber Washers

Summary of the content on the page No. 5

5 ASSEMBLY GUIDE GRILL Assembly Part Qty Fasteners A3– Grill Stand 1 A4– Axle Rod 1 – Grill Head 1 A5 – 2 Wheel Retaining A6 Wheels Clip Flat Washer (qty 2) (qty 2) Step 3: Install a wheel retaining clip to one end of the axle. install one flat washer as shown below. After the flat washer, install a wheel. Be sure to orient the wheel as shown. Now insert the axle (with wheel installed) through the grill stand axle holes as shown below. Next,

Summary of the content on the page No. 6

6 GRILL Head Assembly ASSEMBLY GUIDE Step 1: Unfold the grill stand. Ensure that the locking clip engages at the rear of the stand. Attach the grill head to the grill stand by inserting the tab shown into the grill stand, then allow the grill head to rotate forward while pulling the latch handle. Ensure that the latch handle is fully engaged by pulling up on the grill head. Grill Head Slot Grill Stand Locking Clip (Shown engaged) Engage Grill Pull Handle to Head Clip

Summary of the content on the page No. 7

7 GRILL Head Assembly ASSEMBLY GUIDE Step 2: Install the Regulator Control Valve by first sliding the regulator lock toward the rear of the grill, inserting the Regulator Control Valve fully into the exposed burner tube, and then releasing the regulator lock. Step 3: Place the Trough and Cooking Grate in position as shown below. Assemble the Side Shelves by inserting the side shelf mounting rods into the side shelf busing. Regulator Lock Regulator Cooking Grate Trough

Summary of the content on the page No. 8

8 GRILL CARRY POSITION To transport your grill, first allow the grill to cool completely. ? Remove the propane cylinder from the grill head. ? Remove and store the side shelves inside the grill head. ? Then be sure that the grill lid latch is locked down securely. ? Remove the grill head and set it aside. ? Fold up the grill stand. ? Attach the grill head to the grill stand in the carry position. To release the grill stand into the Carry position, flip the grill stand lock down and caref