Summary of the content on the page No. 1
TM
STAR TRAC FITNESS
PERSONAL VIEWING SCREEN
OWNER ’ S MANUAL
Summary of the content on the page No. 2
TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Before You Get Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 3
TM iPULSE E-UBi, E-RBi, E-STi, AND E-TBTi TM iPULSE E-TRi STAR TRAC PERSONAL VIEWING SCREEN OWNER’S GUIDE 3
Summary of the content on the page No. 4
INTRODUCTION Thank you for adding the STAR TRAC PERSONAL VIEWING SCREEN (PVS) to your Star Trac Purchase. The Personal Viewing Screen has been designed to provide the user with the most rewarding experience based upon the carefully planned features it possess. The design elements of this Personal Viewing Screen will provide you with a comfortable, intu- itive, safe and reliable experience, guiding you to a habit-forming lifestyle. Star Trac's mission is to provide products to mold lifelong habit
Summary of the content on the page No. 5
BEFORE YOU GET STARTED CHECK FACILITIES PREPAREDNESS For a proper installation, please read this guide thoroughly and follow the instructions. Star Trac’s goal is to help you have a successful and reliable installation, for this reason we have come up with some helpful tips and check list to accomplish this goal. EQUIPMENT LAYOUT Check to see that the equipment you will be adding the PVS to are place where they will be used. It is recommended that you follow your installation guides for each on
Summary of the content on the page No. 6
WARNINGS AND CAUTIONS ATTENTION RISQUE DE CHOC ELECTRIQUE, NE PAS OUVRIR PRECAUCION RIESGO DE CHOQUE ELECTRICO NO ABRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER ( OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lighting flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magni
Summary of the content on the page No. 7
This STAR TRAC Personal Viewing Screen has been engineered and manufactured to assure your safety. Before using this product, be sure to read your user’s manual in order to maximize the life of your display. DO NOT disassemble the PVS. Any Un-authorized maintenance will void the warrenty. Un-experienced technicians can cause serious damage, electric shock, and other hazards. Contact your dealer or an experienced technician for repair. DO NOT place sharp tools such as pin or metallic object nea
Summary of the content on the page No. 8
STAR TRAC PERSONAL VIEWING SCREEN (PVS) UNPACK YOUR PERSONAL VIEWING SCREEN Inspect the shipping carton for any parts that may be missing BEFORE discarding the carton. Items can shift during transportation, and may be accidentally discarded with the carton. If any parts are missing, please contact Star Trac Product Support at 800-503-1221. Have the serial number of the PVS, and a list of the missing parts ready so they may be shipped to you. The Personal Viewing Screen is shipped in one box s
Summary of the content on the page No. 9
• Power Cord, Nema 6-15 (NOT INCLUDED IN THE E-TRi KIT) • Power Cord, Nema 5-15 (NOT INCLUDED IN THE E-TRi KIT) • Owners Manual PAL/SECAM Kit (Europe, Middle East) NOTE: there are 4 different kits ie. E-TRi, E-TBTi/E-UBi, E-RBi, AND E-STi. • PVS assembly with Mounting Bracket, Cables, and Display Cap with Grommet (There are 5 cables in the neck) • Center Console Keypad Assembly • Entertainment Headphone Jack and Mount • (2) 5” Tie straps • (2)M8 x 20mm Buttonhead Screws • (1)M8 x 20mm Buttonhe
Summary of the content on the page No. 10
INSTALLING YOUR PERSONAL VIEWING SCREEN (PVS) The Star Trac Personal Viewing Screen is different for each of your Star Trac E-Series Cardio prod- ucts. Make sure you have the proper kit for the E-Series product you are installing. The E-UBi, E-RBi, E-TBTi, and the E-STi will follow the same basic steps for installation. For the E-TRi turn page 18 in this section. To install on the E-UB, E-RB, E-TBT, and the E-ST, follow these steps: STEP 1 Using a #2 Phillips screwdriver, remove the (8) screws
Summary of the content on the page No. 11
After all the cable/harnessing has been disconnected, place the front display plastics aside for later use. Be careful with the display and place it face down on top of a non-scratching surface. You can use the foam bag that ships inside the Personal Viewing Screen package to place the display face onto. This will help protect it from being damaged. Screws STEP 4 Remove the cap cover with the Star Trac logo from the plastics by removing the (2) screws using a #2 Phillips screwdriver. Retain th
Summary of the content on the page No. 12
M8 Buttonhead STEP 7 Install the (4) M8 Buttonhead Screws through the PVS mounting bracket into the display mount. Note: (2) of the screws are in the PVS kit, (2) retained from step 5. Do not tighten them at this time. Screws STEP 8 Adjust the cap with the grommet into place. Using the 5mm Hex Key, tighten the M8 Buttonhead Screws to 190 lb-in (21.5 N-m) of torque. Take the (2) Phillips head screws you removed from the original cap and snugly tighten screws down using Cap a #2 Phillips screwd
Summary of the content on the page No. 13
Screw STEP 10 Using a #2 Phillips head screwdriver, remove the screw that holds in the blank cover where the new Head Phone Jack mount will go. Next remove the blank cover. You will no longer need this item and it can be stored away for any possible future use. Retain screw for later use. Blank cover STEP 11 Take the PVS center console from the kit. STEP 12 Insert the new center console into the front display. Using a #2 Phillips screwdriver, screw in the (4) screws that were saved from the or
Summary of the content on the page No. 14
With the changes now completed on the display, it is now time to re-install the display to the base unit. There are the (3) cables from the PVS mount that will need to be attached to the display. One cable from the PVS mount will be fed through the display which will be connected to the head phone jack later. The fifth cable from the PVS mount, which is the coax, will be connected to the coax on the base unit. There are (2) cables from the base unit that will be connected to the display. Use
Summary of the content on the page No. 15
STEP 16 Using a tie wrap from the PVS kit, bind the cables from the PVS neck to one side of the display mount. Take the tie and put it through the hole on one of the display mount tubes. Tie Wrap STEP 17 Now, take the front display plastics with the new Center Console to the base unit. Hold the front display plastics at the top with one hand while con- necting the cables/harnesses with the other. There is no particular order in connecting the cables/harnessing. However, it may be best to star
Summary of the content on the page No. 16
STEP 19 Feed the Head Phone Jack cable from the PVS display neck through the hole in the front display plastics where the blank cover was removed earli- er. STEP 20 Now that all the cables are in their places, and con- fined to the post on the display mount. Place the display front plastic onto the back. Make sure the bottom of the display front is under the 2 tabs on the display mount. Press the front display against 2 the round tube and rotate it to the back. Be care- ful not to pinch any w
Summary of the content on the page No. 17
STEP 23 Now with the Personal Viewing Screen installed on your Star Trac equipment, it is time to connect your entertainment cable and power to the unit Look at the bottom of the neck, next to the floor. Connect your in-house Entertainment cable to the RF input. Take the power supply from the PVS kit and plug the small barrel connector to the DC input. Now take the appropriate Power Adapter Cable from the kit and plug it into the power supply and the elec- trical receptacle. Only use the powe
Summary of the content on the page No. 18
To install on the E-TR, follow these steps: Screws Screws STEP 1 Using a #2 Phillips screwdriver, remove the (8) screws from the upper back of the display. Place the cover somewhere safe to keep it from being damaged. Next, remove the (6) screws from the lower back of the display. Place the cover with the other one. Retain all the screws for later use. Screws Screws Cap STEP 2 Now remove the upper cap cover that has the STAR TRAC logo on it. This cap is held in by the upper back cover. You
Summary of the content on the page No. 19
Ribbon STEP 4 Detach the Center Console Ribbon Cable from the display board by gently pulling on the ribbon con- nector. Using a #2 Phillips screwdriver to remove Screws Screws the (4) screws that hold the center console in place. Retain the screws for later use. Remove the center console. You will no longer need this center console and, if desired, you can store it away for any possible future use. STEP 5 Take the Personal Viewing Screen from the PVS kit. Next, take the (3) M8 Buttonhead s
Summary of the content on the page No. 20
STEP 8 Now that the PVS is mounted to the Treadmill, you 2 need to route the wires to their proper places. 4 1 Take the coax cable and feed it all the way down the treadmill neck. Center Console Hole 2 Feed the DC power cable from the treadmill neck through the center console hole. 1 3 Next take the Head Phone Jack cable from the PVS neck and connect it to the Head Phone Jack. 3 4 Now feed the other (3) cables through the dis- Bottom View play and out the center console hole. STEP 9 Take the Ent
