Vision Fitness X6200HRT/DA user manual

Summary of the content on the page No. 1

Assembly
Guide
X6000DA & X6200HRT/DA
DUAL-ACTION ELLIPTICAL TRAINERS

Summary of the content on the page No. 2

X6200HRT/DA X6000DA dual-action elliptical trainers To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order. Before proceeding though, find your new Elliptical Trainer’s serial number, located on the front foot axle tube, and enter here: Refer to this number when calling for service, and also enter this serial number on your Warranty Card and in your own records. Be sure to read your Owner’s Guide before using your new Elliptical Trainer. If a

Summary of the content on the page No. 3

TOOLS, HARDWARE, & PARTS INCLUDED MM 5 Allen Wrench PINK BAG MM 13 Wrench Screwdriver MM M8 x 45 Bolt Quantity: 2 (X6000DA only) MM M8 x 80 Bolt Quantity: 4 M8 Nylock Nut MM 5 L-Shaped Wrench Quantity: 4 PARTS BOX ORANGE BAG Rear Folding Axle, Qty: 1 • Stabilizer w/ Rubber Cover, Qty: 2 Toe Pieces, Qty: 2 • Rear Wheels, Qty: 2 Tension Control Knob, Qty: 1 (Model X6000DA only) Console, Qty: 1 • Power Supply, Qty: 1 (X6200HRT/DA only) MM • 13 Nut Cap, Qty: 2 • Water Bottle & Bracket, Qty: 1 • MM

Summary of the content on the page No. 4

GREEN BAG BLUE BAG M8 Lock Washer Quantity: 2 MM M8 x 16 Bolt M16 Wavy Washer Quantity: 2 Quantity: 2 M8 Washer Quantity: 2 MM M16 Washer M8 Washer M5 x 25 Bolt MM Quantity: 2 Quantity: 2 Quantity: 1 M8 x 60 Bolt (X6000DA only) Quantity: 2 BLACK BAG M8 x 25 Washer M16 Wavy Washer Quantity: 2 Quantity: 2 MM M8 x 36 Bolt Quantity: 2 MM M6 x 12 Bolt Quantity: 2 MM M8 x 13 Nylock Nut Quantity: 2 MM M8 x 12 Bolt M26 Wavy Washer M8 x 35 Washer Quantity: 4 Quantity: 2 Quantity: 2

Summary of the content on the page No. 5

STEP 1 ORANGE BAG • Install the left and right stabilizers with MM the four bolts (M8 x 16 ), using the MM Blue 5 Allen wrench. • Cover both stabilizers with the included rubber covers. • Insert the rear folding axle shaft into the rear tube. STEP 1 STEP 2 STEP X6200HRT/DA 2 BLUE BAG Only • Slide a wavy washer (M16) onto the right-hand side of the rear folding axle, followed by the right-hand pedal arm guide rail (the guide rails each have a blue indicator arrow printed on their sides; these ar

Summary of the content on the page No. 6

STEP 3 PINK BAG • Mount the rear pedal arms to the front pedal arms using four bolts MM (M8 x 80 ) and four M8 NyLock MM nuts. Tighten with the 13 wrench. • X6000DA only: Install the foot toe pieces to the front pedal arms with MM two bolts (M8 x 45 ) using the Blue MM 5 Allen wrench. STEP 3 X6000DA Only 6

Summary of the content on the page No. 7

STEP 4 STEP 4 GREEN BAG • X6000DA only: Unfold the RPM sensor wire, located in the frame console mast bracket. Remove any kinks. • All models: Slide the rubber console X6000DA mast cover onto the bottom of console mast, and slide it up as far as it will go. • All models: Unfold the console cable and attach it to the string located at the bottom of the console mast. Guide the wire up through the mast while simultaneously sliding the console mast X6200HRT/DA onto the frame bracket. • All models:

Summary of the content on the page No. 8

STEP 5 BLACK BAG • Slide a large wavy washer (M26) onto the console mast axle. Locate and slide the right upper handlebar bracket onto the console mast axle and attach with a washer (M8 x 35) and M8 NyLock nut, using MM the 13 wrench. Snap the plastic MM 13 nut caps over the nuts. STEP 5 • Slide a small wavy washer (M16) onto the lower pedal arm support, followed by the right lower arm. Attach with a washer (M8 x 25) and MM MM bolt (M8 x 12 ), using the Blue 5 Allen wrench. • Pivot the lower