Summary of the content on the page No. 1
Remote Cont Rolle R
o wne R’s m anaul
SMA/SMH24SC
Single Zone Mini-Splits
Heat Controller, Inc. • 1900 Wellworth Ave. • Jackson, MI 49203 • (517)787-2100 • www.heatcontroller.com
Summary of the content on the page No. 2
Owner’s Manual Remote ContR olleR Heat Controller, Inc. Contents Remote Controller Specifications........................................................................2 Features of the Remote Controller...................................................................2-3 Remote Controller Display Indicators .................................................................3 Operating Instructions .........................................................................................4 Warning
Summary of the content on the page No. 3
Heat Controller, Inc. Remote ContR olleR Owner’s Manual Remote Controller Specifications R51D/BGE, R51K/BGCE, R51K1/BGE, R51K1/ Model* BGCE Rated Voltage 3.0V Lowest Voltage of CPU Emitting Signal 2.0V Reaching Distance 26'3" (8m) Environment Temperature Range -41°F~140°F (-5°C~60°C) *NOTE: Temperature setting display: Celsius scale (°C): R51K/BGE, R51K/BGCE; Fahrenheit scale (°F): R51K1/BGE, R51K1/BGCE; Features 1. Operating Mode: COOL, HEAT (for heat pump models only), DRY, FAN and AUTO 2
Summary of the content on the page No. 4
Owner’s Manual Remote ContR olleR Heat Controller, Inc. Remote Controller Display Indicators LOCK (heat pump only models): This is displayed by pushing the LOCK button. Push the LOCK button again to clear display. LOCK prevents the current settings from being changed. 4 TIMER Display: This display area shows the settings of TIMER. If the starting time is set, it will display TIMER ON. If the stop time is set, it will display TIMER OFF. If both operations are set, it will show TIMER ON- OFF w
Summary of the content on the page No. 5
Heat Controller, Inc. Remote ContR olleR Owner’s Manual operation Instructions 1. Install/Replace Batteries A. B. • • If you do not use the remote controller for an extended period of time, remove the batteries. Otherwise battery leakage may damage the remote controller. • • Replace the batteries when there is no beep from the indoor unit of if the Transmission Indicator light fails to appear when buttons are pressed on the remote controller. 2. Automatic operation When the air conditioner
Summary of the content on the page No. 6
Owner’s Manual Remote ContR olleR Heat Controller, Inc. 3. COOL, HEAT and FAN ONLY Operation A. If the AUTO mode is not desirable, manually override the settings by using COOL, DRY, HEAT (heat pump models only), or FAN ONLY modes. B. Press the TEMP button to set the desired room temperature from 70°F (21°C) to 82°F (28°C). C. Press the FAN SPEED to select the FAN mode of AUTO, HIGH, MED or LOW. D. Press the ON/OFF button. The operation lamp lights and the air conditioner starts to oper- ate per
Summary of the content on the page No. 7
Heat Controller, Inc. Remote ContR olleR Owner’s Manual 6. Setting the timer to stop the unit’s operation A. B. C. D. E. F. 7. Set the STARTING & STOPPING time A. B. C. D. E. F. • • 6
Summary of the content on the page No. 8
Owner’s Manual Remote ContR olleR Heat Controller, Inc. TEMP Button ▼: Push the TEMP button to decrease the indoor temperature setting or to adjust 8 the TIMER in a counter-clockwise direction. 9 MODE Select Button: Each time you push the button, a mode is selected in a sequence that goes from AUTO, COOL, DRY, HEAT and FAN as the following figure indicates: * AUTO COOL DRY HEAT FAN *NOTE: HEAT feature only for heat pump models. 10 SWING Button: Press this button to change the louver angle whic
Summary of the content on the page No. 9
Heat Controller, Inc. Remote ContR olleR Owner’s Manual Warning • Be sure there are no barriers between the remote controller and the receiver of the indoor unit, otherwise the air condi- tioner may not receive the signal from the remote. • Keep the remote controller away from all liquids. • Keep the indoor receiver out of direct sunlight. • Keep controller away from other applications that may create an EMI (Electro-Magnetic Interference). 8
Summary of the content on the page No. 10
08/2010 04/2009
