Summary of the content on the page No. 1
MODEL T24638
ELECTRIC MEAT GRINDER
INSTRUCTIONS
For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com
Introduction
t he Model t 24638 is great for grinding meat,
stuffing sausage, and making kubbe.
To reduce the risk of serious personal injury
when using the grinder:
• Disconnect grinder from power before
Inventory
disassembling for cleaning, changing
Description Qty
components, or reassembling. Make sure
A. electric Meat g rinder .......
Summary of the content on the page No. 2
Do not place motor housing in water—doing • Allow grinder to come to a complete stop so will damage it. Wipe motor housing with before using reverse. Only run grinder for damp cloth. a few seconds in reverse, as prolonged use will damage motor. • Turn OFF and disconnect grinder if it jams Cleaning and wait until it has come to a complete t o prevent contamination and illness, you must stop before removing jammed material. clean and sanitize the components of this meat • Do not force
Summary of the content on the page No. 3
Sanitizing Assembly 1. disConneCt grinder FroM poWer! 2. place the meat grinder on a level surface, When cleaning with sanitizers, always fol- and adjust the lock knob shaft so it is flush low the recommendations on the manufac- with the inside of the meat grinder, as shown turer’s label, and make sure that the product in figure 3. will do the job for which you intend. Never use a product that will cause exposed sur- faces to render meat unsafe for human con- Lock Knob sumption. failur
Summary of the content on the page No. 4
4. slide the thinner flat washer and thicker nylon 7. thread the lock ring onto the grinding head to washer onto the large end of the auger, then secure the auger and grinding plate—but do insert the auger into the drive shaft, as shown not overtighten it—then insert the hopper tray in figure 5. throat onto the grinding head (see figure 8). Note: If necessary, wiggle the auger to seat it in the drive shaft. hopper tray auger throat Lock ring Washers figure 8. Lock ring and hopper tray ins
Summary of the content on the page No. 5
ground meat will flow out of the grinder, as D. re-install the grinding blade, grinding shown in figure 10. plate and lock ring. E. reconnect the grinder to power and fol- low instructions for grinding. Sausage Stuffing 1. disConneCt grinder FroM poWer! 2. install the grinding head and auger (follow Steps 2–4 of Assembly on pages 3–4). Note: The grinding blade and grind plates are not installed during sausage stuffing. figure 10. grinder processing meat. 3. slide the sausage stuffing plate
Summary of the content on the page No. 6
6. install the hopper tray (see figure 12 on 3. insert the kubbe attachment onto the auger, page 5). then place the kubbe flange over the attach- ment, as shown in figure 13. 7. slide a casing onto the stuffing tube. 8. place ground meat onto the hopper tray, Kubbe Flange press the on button, then feed the meat into the throat using the tamper. 9. While feeding meat into the grinder, hold the casing on the stuffing tube and allow it to fill. 10. turn the grinder OFF, tie the end of the
Summary of the content on the page No. 7
Troubleshooting s ymptom possible Cause possible solution g rinder does not 1. power supply switched OFF or is at fault. 1. ensure power supply is switched ON; ensure power start or a breaker grinder not connected to power. supply has the correct voltage. Connect grinder to trips. power. 2. Wall fuse/circuit breaker is blown/tripped. 2. ensure circuit size is suitable; replace weak breaker; avoid overloading grinder with too much meat. reset circuit breaker on grinder. 3. Wiring is open/has
Summary of the content on the page No. 8
T24638 parts breakdown and List 16 18 15 14 17 29 28 13 6 12 19 9 7 8 20 5 4 21 3 22 2 1 11 10 23 24 25 26 27 REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PT24638001 LOCK RING 16 PT24638016 MEAT TAMPER 2 PT24638002 STUFFING TUBE BASE 17 PT24638017 LOCK KNOB 3 PT24638003 LARGE STUFFING TUBE 18 PT24638018 ACCESSORY COVER 4 PT24638004 MIDDLE STUFFING TUBE 19 PT24638019 CORD COVER 5 PT24638005 SMALL STUFFING TUBE 20 PT24638023 POWER CORD 18G 3W 48" 5-15 PLUG 6 PT24638006 SAUSAGE STUFFING PLATE 21
