Hobart 1812 user manual

Summary of the content on the page No. 1

1812 SLICER
TECHNICAL MANUAL




SPECIFICATION SHEET
INSTALLATION INSTRUCTIONS
OPERATION INSTRUCTIONS
CLEANING INSTRUCTIONS
MAINTENANCE INSTRUCTIONS
TROUBLE SHOOTING INSTRUCTIONS
WIRING DIAGRAMS
CATALOG OF REPLACEMENT PARTS
SMARTPARTS™ USER GUIDE
RECOMMENDED SPARE PARTS LIST

Summary of the content on the page No. 2

Need other Hobart Services? • Warranty Registration • Delivery and Installation • Preventive Maintenance • Hobart Service Contracts • Extended Warranty Contracts • Parts and Accessories • Specialty Programs • Water Treatment Programs 1812 SLicer Technical Maunal Page 2 of 49

Summary of the content on the page No. 3

1812 SLicer Technical Maunal Page 3 of 49

Summary of the content on the page No. 4

1812 SLicer Technical Maunal Page 4 of 49

Summary of the content on the page No. 5

1812 SLicer Technical Maunal Page 5 of 49

Summary of the content on the page No. 6

1812 SLicer Technical Maunal Page 6 of 49

Summary of the content on the page No. 7

1812 SLicer Technical Maunal Page 7 of 49

Summary of the content on the page No. 8

1812 SLicer Technical Maunal Page 8 of 49

Summary of the content on the page No. 9

1812 SLicer Technical Maunal Page 9 of 49

Summary of the content on the page No. 10

1812 SLicer Technical Maunal Page 10 of 49

Summary of the content on the page No. 11

1812 SLicer Technical Maunal Page 11 of 49

Summary of the content on the page No. 12

1812 SLicer Technical Maunal Page 12 of 49

Summary of the content on the page No. 13

1812 SLicer Technical Maunal Page 13 of 49

Summary of the content on the page No. 14

1812 SLicer Technical Maunal Page 14 of 49

Summary of the content on the page No. 15

1812 SLicer Technical Maunal Page 15 of 49

Summary of the content on the page No. 16

1812 SLicer Technical Maunal Page 16 of 49

Summary of the content on the page No. 17

TROUBLESHOOTING 1812 SLICER SYMPTOM POSSIBLE CAUSE Motor will not start, switch in start 1. No power to slicer. position. 2. Carriage tray unit not in home position. 3. Check power cord. Power switch in run position, motor will 1. Off – On – Start switch malfunction. not stay running. Slicer will not shut off. 2. Off – On – Start switch malfunction. Hard to slice. 1. Blade dull. 2. Carriage bearing assembly not free on slide rods. NOTE: If symptom(s) persists after possible caus

Summary of the content on the page No. 18

1812 SLicer Technical Maunal Page 18 of 49 1CR 1S ON/OFF 2 4 GREEN 2LS ELECTRICAL AND GROUNDING CONNECTIONS MUST HOME WHITE BLUE 2 3 4 1 COMPLY WITH THE NATIONAL ELECTRICAL CODE AND/OR OTHER APPLICABLE LOCAL CODES. 1PL 1MTR W 2 WHITE 1CR MOTOR BLK ELECTRONIC 1812/1912 SLICER W/HOME START 68 RED START 1 3 SWITCH GRN ELECTRICAL DIAGRAM 100/120V 50/60Hz 4 GND 1LS START INTERLOCK RED 0 1 1 RED CR YELLOW C NC WHT VIOLET DERIVED FROM F18667 1S ON/OFF 3LS GREEN ELECTRICAL AND GROUNDING 2LS CONNECTION

Summary of the content on the page No. 19

CATALOG OF REPLACEMENT PARTS SLICERS (INCLUDES MOTOR PARTS) 1812 ML-104550 1912 ML-104552 THIS MANUAL REPLACES AND SHOULD BE USED INSTEAD OF FORM 18652 PRIOR ML’S COVERED IN THIS MANUAL: ML-104275 ML-104377 A product of HOBART CORPORATION 701 RIDGE AVENUE TROY, OHIO 45374-0001 FORM 19315 Rev. A (10-99) 1812 SLicer Technical Maunal Page 19 of 49

Summary of the content on the page No. 20

1812/1912 REPLACEMENT PARTS 22-23-24 21 16-17-18 19 20 13-14-15 25 26 7 11-12 8 9 1 THRU 6 10 PL-51152 ELECTRICAL UNIT ILLUS. PART PL-51152 NO. NAME OF PART AMT. 1 123856-1 Cord & Plug Assy.(Under 150 V.) .................................................................................................1 2 123856-2 Cord & Plug Assy. (200 - 250 V.) .................................................................................................1 3 123858 Cord Assy.(I.E.C.) .........................