Desa VFRMV18PA user manual

User manual for the device Desa VFRMV18PA

Device: Desa VFRMV18PA
Category: Electric Heater
Manufacturer: Desa
Size: 7.73 MB
Added : 10/8/2014
Number of pages: 31
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Desa VFRMV18PA. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Desa VFRMV18PA.

For your convenience

If looking through the Desa VFRMV18PA user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Desa VFRMV18PA on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Desa VFRMV18PA to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Desa VFRMV18PA User manual - Online PDF
Advertisement
« Page 1 of 31 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Desa VFRMV18PA but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Desa VFRMV18PA. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

UNVENTED (VENT FREE)
ANSI Z21.11.2a-2003
GAS LOG HEATER
ANSI Z21.60-2003
OWNER’S OPERATION AND
CSA 2.26-2003
INSTALLATION MANUAL
APPROVED
For more information, visit www.desatech.com
VFRMV18NA, VFRMV18PA
VFRMV24NA, VFRMV24PA
Vent-free Models Also Design--Certified As Vented Decorative Appliances
WARNING: Improper installation, ad-
WARNING: If the information in this manual
justment, alteration, service, or main-
is not followed exactly, a fire or explosion
tenance can cause injury or property

Summary of the content on the page No. 2

TABLE OF CONTENTS 2 SAFETY INFORMATION TABLE OF CONTENTS CLEANING AND MAINTENANCE.............................................. 18 SAFETY INFORMATION ..............................................................2 TROUBLESHOOTING ...............................................................19 PRODUCT IDENTIFICATION ......................................................3 SPECIFICATIONS ......................................................................22 OPTIONAL REMOTE CONTROL ACCESSORIES .

Summary of the content on the page No. 3

SAFETY INFORMATION 3 3 PRODUCT IDENTIFICATION SAFETY INFORMATION Continued ing. Make sure the selector switch is in the OFF position (Remote- 1. This appliance, as supplied, is only for use with the type of gas indicated Ready Models Only). Only a qualified service person should install, on the rating plate. This appliance is not convertible for use with other service, or repair heater. gases. 15. Make sure the selector switch is in the OFF position when you are away 2. Do not place propane

Summary of the content on the page No. 4

OPTIONAL REMOTE CONTROL ACCESSORIES LOCAL CODES 4 UNPACKING PRODUCT FEATURES AIR FOR COMBUSTION AND VENTILATION PROVIDING ADEQUATE VENTILATION OPTIONAL REMOTE CONTROL SAFETY DEVICE ACCESSORIES This heater has a pilot with an Oxygen Depletion Sensing (ODS) safety shut off system. The ODS/pilot is a required feature for vent-free room heaters. There are four optional remote controls that can be purchased sepa- The ODS/pilot shuts off the heater if there is not enough fresh air. rately for Rem

Summary of the content on the page No. 5

AIR FOR COMBUSTION AND VENTILATION 5 5 Providing Adequate Ventilation (Cont.) Determining Fresh-Air Flow for Appliance Location AIR FOR COMBUSTION AND 2.Multiply the space volume by 20 to determine the maximum Btu/Hr the VENTILATION space can support. Continued ____________(volume of space) x 20 = (Maximum Btu/Hr the space can support) Unusually tight construction is defined as construction where: Example: 25

Summary of the content on the page No. 6

AIR FOR COMBUSTION AND VENTILATION 6 Ventilation Air AIR FOR COMBUSTION AND VENTILATION Continued VENTILATION AIR Ventilation Air From Inside Building 12" This fresh air would come from an adjoining unconfined space. When ven- tilating to an adjoining unconfined space, you must provide two permanent Ventilation openings: one within 12" of the ceiling and one within 12" of the floor on the Ventilation Grills Grills wall connecting the two spaces (see options 1 and 2, Figure 2). You can also

Summary of the content on the page No. 7

INSTALLATION 7 7 Check Gas Type Installation and Clearences for Vent-free Operation INSTALLATION NOTICE: this heater is intended for use as supplemental heat. Use CAUTION: This heater creates warm air currents. These cur- this heater along with your primary heating system. Do not install this rents move heat to wall surfaces next to heater. Installing heater heater as your primary heating source. If you have a central heating next to vinyl or cloth wall coverings or operating heate

Summary of the content on the page No. 8

INSTALLATION 8 Installation and Clearences for Vent-free Operation (cont.) INSTALLATION Continued Care fully follow the instructions below. This will ensure safe installation If Using Mantel into masonary, UL127-listaed manufactured fireplace, or listed vent-free firebox. You must have non-combustible material(s) above the fireplace opening. Non-combustible materials (such as slate, marble, tile, etc.) must be at least 1/2 inch thick. With sheet metal, you must have non-combustible material

Summary of the content on the page No. 9

INSTALLATION 9 9 Mantel Clearances Floor Clearances INSTALLATION M a n te l S h e lf Continued 1 0 " U n d e rs id e o f 8 " M a n te l S h e lf 6 " MANTEL CLEARANCES 1 2 /2" In addition to meeting non-combustible material clearances, you must also meet A ll m in im u m required clearances between fireplace opening and mantel shelf. If you do not d is ta n c e s a re in in c h e s meet the clearances listed below, you will need a hood. M in im u m N o n - ( A ) C o m b u s tib le Det

Summary of the content on the page No. 10

INSTALLATION 10 Installing Damper Clamp Accessory for Vented Operation Installing Heater Assembly INSTALLATION Continued INSTALLING DAMPER CLAMP ACCESSORY INSTALLING HEATER ASSEMBLY FOR VENTED OPERATION WARNING: If installing in a sunken fireplace, special care is needed. You must raise the fireplace floor to allow access to heater control panel. Note: When used as a vented decorative, appliance must be installed only in a solid-fuel burning fireplace with a working flue and constructed of non-

Summary of the content on the page No. 11

INSTALLATION 11 11 Installing Heater Assembly (Cont.) Connecting to Gas Supply INSTALLATION CONNECTING TO GAS SUPPLY Continued Installation must include an equipment shutoff valve, union, and plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge hook up. NPT WARNING: This appliance requires a 3/8" NPT (National Pipe tap must be upstream from heater (see Figure 13 page 12, depending on Thread) inlet connection to the pressure regulator. your model). IMPORTANT: Install equipment s

Summary of the content on the page No. 12

INSTALLATION 12 Connecting To Gas Supply (Cont.) Checking Gas Connections INSTALLATION Continued 3. Pressurize supply piping system by either opening propane/LP supply tank valve for propane/LP gas or opening main gas valve located on or near gas CSA Design-Certified Equipment Shutoff PROPANE/LP meter for natural gas, or using compressed air. Valve With 1/8" NPT Tap* - From External 4. Check all joints of gas supply piping system. Apply noncorrosive leak Approved Flexible Gas Regulator dete

Summary of the content on the page No. 13

INSTALLATION 13 13 Checking Gas Connections (Cont.) INSTALLATION Continued Equipment Shutoff Valve Propane/LP Thermostat Gas Supply Valve or Control Valve Location Figure 15 - Checking Gas Joints (propane/LP only) Thermostat Gas Thermostat Gas Valve or Control Valve or Control Valve Location Valve Location Gas Meter Figure 16 - Checking Gas Joints (Natural Gas Only) For more information, visit www.desatech.com 114745-01 114745-01

Summary of the content on the page No. 14

� � � � OPERATING HEATER (REMOTE-READY MODELS) 14 For Your Safety Read Before Lighting Lighting Instructions OPERATING HEATER NOTICE: During initial operation of new heater, burning logs will REMOTE-READY MODELS give off a paper-burning smell. Orange flame will also be present. Open damper or window to vent smell. This will only last a few FOR YOUR SAFETY READ hours. BEFORE LIGHTING Note: Home owners generally prefer to operate their heater with the chimney damper closed. This will put all t

Summary of the content on the page No. 15

� ���� ��������� � � � OPERATING HEATER (REMOTE-READY MODELS) Lighting Instructions (Cont.) 15 15 To Turn Off Gas To Appliance Manual Lighting Procedure Remote Control Operation OPERATING HEATER Continued pressing ignitor button until pilot lights. Ignitor Pilot Burner Ignitor Pilot Electrode Note: If pilot does not stay lit, contact a qualified service person or gas Electrode Burner supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual

Summary of the content on the page No. 16

� ���� ��������� � � � OPERATING HEATER (REMOTE-READY MODELS) 16 Remote Control Operation (Cont.) OPERATING HEATER Continued IMPORTANT: To turn the pilot off, manually turn the control knob IMPORTANT: Do not leave the selector switch in the REMOTE or on the heater to the OFF position. ON position when the pilot is not lit. This will drain the battery. ������������������ 2. Press the ON/OFF button to turn the burners on and off. When ����� ������� ������������ turning burners off, the pilot

Summary of the content on the page No. 17

INSPECTING BURNERS 17 17 Pilot Flame Pattern Burner Flame Pattern INSPECTING BURNERS BURNER FLAME PATTERN Figure 24 shows correct burner fl ame pattern. Check pilot fl ame pattern and burner fl ame patterns often. NOTICE: Do not mistake orange fl ames with yellow tipping. Dirt PILOT FLAME PATTERN or other fi ne particles are burned by heat er, causing brief patches Figure 22 shows a correct pilot fl ame pat tern. Figure 23 shows an incorrect of orange fl ame. pilot fl ame pattern. The incorrect pilo

Summary of the content on the page No. 18

CLEANING AND MAINTENANCE 18 Cleaning Burner Injector Holder and Pilot Air Inlet Hole CLEANING AND MAINTENANCE WARNING: Failure to keep the primary air openings of the burner clean may result in sooting and property damage. WARNING: Turn off heater and let cool before cleaning. CAUTION: You must keep control areas, burners, and circulating Ports air passageways of heater clean. Inspect these areas of heater be- Slots fore each use. Have heater inspected yearly by a qualified service I

Summary of the content on the page No. 19

TROUBLESHOOTING 19 19 TROUBLESHOOTING Note: For additional help, visit WARNING: Turn off and un- CAUTION: Never use a wire, DESA technical service web site at plug heater and let cool before needle, or similar object to clean www.desatech.com. servicing. Only a qualified service ODS/pilot. This can damage ODS/ person should service and repair pilot unit. Note: All troubleshooting items are listed heater. in order of operation. OBSERVED PROBLEM POSSIBLE CAUSE REMEDY When ignitor button

Summary of the content on the page No. 20

TROUBLESHOOTING 20 TROUBLESHOOTING Continued OBSERVED PROBLEM POSSIBLE CAUSE REMEDY One or both burner does not light after ODS/pilot 1. Inlet gas pressure is too low 1. Contact local natural or propane/LP gas com- is lit pany 2. Burner orifice(s) clogged 2. Clean burner(s) (see Cleaning and Mainte- nance, page 18) or replace burner orifice(s) 3. Contact qualified service person 3. Mislocated crossover tube 4. Replace burner orifice(s) 4. Burner orifice(s) diameter is too small 5. Put remote selecto


Alternative user manuals
# User manual Category Download
1 Desa 000 BTU SPC-30R User manual Electric Heater 0
2 Desa 000 Btu/hr Models User manual Electric Heater 0
3 Desa 000-12 User manual Electric Heater 0
4 Desa 100 User manual Electric Heater 0
5 Desa 104504-02 User manual Electric Heater 0
6 Desa 000-15 User manual Electric Heater 0
7 Desa 000-30 User manual Electric Heater 0
8 Desa 050 BTU User manual Electric Heater 0
9 Desa 105801-09 User manual Electric Heater 0
10 Desa 105838-02 User manual Electric Heater 0
11 Desa 10 User manual Electric Heater 0
12 Desa 101811-01C.pdf User manual Electric Heater 0
13 Desa 000-24 User manual Electric Heater 0
14 Desa 104506-02 User manual Electric Heater 0
15 Desa 106040-02 User manual Electric Heater 0
16 A.O. Smith AH - 290 User manual Electric Heater 6
17 A.O. Smith AHD 290 User manual Electric Heater 7
18 A.O. Smith AHDS 290 User manual Electric Heater 0
19 A.O. Smith ST 3000 User manual Electric Heater 5
20 A.O. Smith WATER HEATERS User manual Electric Heater 13