Summary of the content on the page No. 1
English Español
Concer Concer Concert Br t Br t Breez eez eeze™ e™ e™
Owner’s Guide and Installation Manual
Manual De Propietario
Form# 45049-01
20090713
©2009 Hunter Fan Co.
Summary of the content on the page No. 2
Welcome For Your Records and Warranty Assistance Your new Hunter ceiling fan is an addition to your home or office that ® For reference, also attach your receipt or a copy will provide comfort and performance for many years. This installation of your receipt to the manual. and operation manual gives you complete instructions for installing and operating your fan. __________________________________________ Model Name We are proud of our work. We appreciate the opportunity to supply you with t
Summary of the content on the page No. 3
Installer’s Choice and Optional Accessories Understanding Mounting and Installer’s Choice® Support Brace Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profile, Standard, or Angled mounting. The steps in this manual include Ceiling Standard instructions for all three Installer’s Choice mounting methods. Outlet Box Mounting Style Co
Summary of the content on the page No. 4
1 • Getting Ready To install a ceiling fan, be sure you can do the following: • Locate the ceiling joist or other suitable support in ceiling. • Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: • Electric drill with 9/64” bit • Standard screwdriver (magne
Summary of the content on the page No. 5
2 • Installing the Hanger Bracket 2-1. Drill two pilot holes into the wood support structure through the outermost holes in the outlet box. The pilot holes should be 9/64” Isolator in diameter. Hanger Note: Your fan comes with four pre-installed neoprene noise Bracket isolators. 2-2. Thread the lead wires from the outlet box down through the hole in the middle of the hanger bracket. 2-3. Align the slotted holes in the hanger bracket with the pilot holes you drilled in the wood support s
Summary of the content on the page No. 6
3 • Assembling and Hanging the Fan You can assemble your fan for standard or angled mounting as shown Steps 3-1 – 3-3 in steps 3-1 – 3-3. For low profile mounting (ceilings less than 8 feet high), go to steps 3-6 – 3-9 on the next page. Downrod 3-1. To assemble fan to hang down from a flat or angled ceiling, place the canopy and canopy trim ring around the adapter so that they Canopy rest on the fan assembly. (with Washer) 3-2. Feed the wires from the fan through the downrod. Note: Mak
Summary of the content on the page No. 7
3 • Assembling and Hanging the Fan (Low Profile Only) You can assemble your fan for standard or angled mounting as shown in steps 3-1 – 3-3 on the previous page. For low profile mounting (ceilings less than 8 feet high), see steps 3-6 – 3-10 on this page. 3-6. Remove the screws from the hanger ball bracket. 3-7. Place the low profile washer from the parts sack into the canopy. 3-8. Place the canopy trim ring and canopy with washer on top of the fan assembly. 3-9. Align the screw holes i
Summary of the content on the page No. 8
4 •Wiring the Fan All wiring must be in accordance with national and local electrical codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician. Wall switches are not included. Select an acceptable general-use switch in accordance with national and local electrical codes. 4-1. Before attempting installation, make sure the power is still off. 4-2. To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise u
Summary of the content on the page No. 9
5 • Installing the Canopy and Canopy Trim Ring Steps 5-1 – 5-2 Hanger Bracket 5-1. Partially install two canopy screws (about 2 full turns) in the hanger bracket. 5-2. Raise the canopy over the hanger bracket. Align partially installed screws with key slots in canopy. 5-3. Twist canopy clockwise to secure. 5-4. Install third & fourth canopy screw in round hole on canopy. Securely tighten all four screws. Canopy Trim Ring Canopy 5-5. Using both hands, push the canopy trim ring up to the t
Summary of the content on the page No. 10
6 • Assembling the Blades Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 6-1. Your fan may include blade grommets. If your fan has grommets, Step 6-1 (Detail) insert them by hand into the holes on the blades. 6-2. Attach each blade to a blade iron using three blade assembly screws. If you used grommets, the blades may appear slightly loose after screws are tightened. This is normal. 6-3. Remove the blade mounting screws and rubber shipping bumper
Summary of the content on the page No. 11
7 • Light/Speaker Assembly Installation 7-1. To attach the upper switch housing, partially install two housing assembly screws into the switch housing mounting plate. 7-2. Feed the upper plug connector through the center opening of the housing. 7-3. Align the keyhole slots in the housing with the housing assembly screws. 7-4. Turn the housing counterclockwise until the housing assembly screws are firmly situated in the narrow end of the keyhole slots. Install the remaining screw into the
Summary of the content on the page No. 12
7 • Light/Speaker Assembly Installation (Continued) 7-5. Feed the two wires from the light kit up through the center hole Lower Switch in the lower switch housing. Housing 7-6. Insert the threaded rod from the light kit/speaker assembly into Threaded Rod the center hole in the lower switch housing. Wires 7-7. Align the screw holes in the bottom of the lower switch housing with the screw holes on top of the light kit/speaker assembly, making sure the pull chain lines up with the chain guide
Summary of the content on the page No. 13
7 • Light/Speaker Assembly Installation (Continued) Wire 7-11. To connect the wires, hold the bare metal leads together and Connections place a wire connector over them, then twist clockwise until tight. Connect the black wire with a white stripe from the lower switch housing to the black wire from the light kit. Connect the white wire from the lower switch housing to the white wire from the light kit/ speaker. Secure all wire connections using wire connectors. 7-12. To attach the lower sw
Summary of the content on the page No. 14
8 •Glass Installation Installing the Glass Bowl 8-1. Remove protective foam ring from threaded portion of light kit/speaker assembly. 8-2. Install B10 candelabra bulbs Threaded (40 Watt Maximum) into the Portion of sockets. Light Kit Assembly Light Bulbs 8-3. Place the glass bowl over the (B10 Candelabra light kit/speaker assembly, ensuring the Base 40 Watt threaded portion of the light kit Maximum) assembly comes out of the bottom of the glass bowl. 8-4. Place the finial over th
Summary of the content on the page No. 15
9 • Operating and Cleaning Your Ceiling Fan 9-1. Turn on electrical power to the fan. 9-2. The fan pull chain controls power to the fan. The pull chain has four settings in sequence: High, Medium, Low, and Off. • Pull the chain slowly to change settings. • Release slowly to prevent the chain from recoiling into the blades. • The chain uses a breakaway connector that separates if the chain is jerked. If this happens, simply reinsert the chain into the connector. 9-3. Ceiling fans work best by
Summary of the content on the page No. 16
10 • Installation and Setup of Maestro™ and Remote To accommodate different audio systems and devices, the Maestro™ can be installed in one of two ways. You can choose to install the Maestro™ with 3.5mm Stereo Cable or you can install it with Speaker Wire. Considering Optional Accessories Consider using Soundolier’s® optional accessories, which include Wireless Subwoofers and Duo™ Lamps. Optional accessories can be purchased through Authorized Hunter Dealers. For quiet and optimum perform
Summary of the content on the page No. 17
10 • Installation and Setup of Maestro™ and Remote (Continued) Maestro™ AC Adaptor Powering the Maestro™: 10-1. Plug the AC adaptor into the back of the Maestro™ in the port labeled power. 10-2. Select the correct channel by sliding the switch to the desired channel. For 3.5mm Stereo Cable Installation: 10-3. Plug a 3.5mm stereo cable into the back of the Maestro™ in the port labeled line in. 10-4. Plug the other end of the 3.5mm stereo cable into your audio device. 3.5
Summary of the content on the page No. 18
11 • Operating the Remote Control (Light/Speaker) Light: Pressing the ON/OFF button on the remote once will turn the light on and pressing the button again will turn the light off. Press to increase the brightness of the light. Press to decrease the brightness of the light. Speaker: Pressing the MUTE button on the remote once will turn the speaker on and pressing the button again will turn the speaker off. Press to increase the VOLUME of the speaker.
Summary of the content on the page No. 19
12 • Changing the channel on the Maestro™ and the Fan NOTE:The Maestro™ transmitter and the fan must be on the Maestro™ same channel to transmit and receive properly. 12-1. To change the channel on the Maestro™, slide the channel selection switch on the lower right corner of the transmitter. 12-2. To change the channel on the fan press the button on the remote. 12-3 The green/red LED indicators on the bottom of the fan display the channel the fan is tuned to. Green LEDs indicat
Summary of the content on the page No. 20
13 • Troubleshooting Problem: Nothing happens; fan does not move. 1. Turn power on, replace fuse, or reset breaker. 2. Loosen canopy, check all connections according to the wiring the fan section. 3. Check the plug connection in the switch housing. 4. Push motor reversing switch firmly left or right to ensure that the switch is engaged. 5. Pull the pull chain to ensure it is on. 6. Remove the shipping bumpers. Problem: Noisy operation. 1. Tighten the blade assembly screws and blade iron arma
