Summary of the content on the page No. 1
®
BARNES
INSTALLATION and OPERATION MANUAL
Submersible Sump Pump
SERIES: BP27, BP27A, BP27D,
& BP27HT
Standard & High Temperature
1/3 HP, 1550 RPM
IMPORTANT: Read all instructions in this manual before operating pump.
As a result of Crane Pumps & Systems, Inc., constant product improvement program, product
changes may occur. As such Crane Pumps & Systems, Inc., reserves the right to change product
without prior written notification.
PUMPS & SYSTEMS
A Crane Co. Company
420 Third Street/P.O.
Summary of the content on the page No. 2
TABLE OF CONTENTS WARNING AND SAFETY PRECAUTIONS.......................................................................... 3 A. PUMP SPECIFICATIONS .................................................................................................... 4 B. GENERAL INFORMATION .................................................................................................. 5 C. INSTALLATION .............................................................................................................
Summary of the content on the page No. 3
SAFETY FIRST! Please Read This Before Installing Or Operating Pump. This WARNING ! Do not pump hazardous materials information is provided for SAFETY and to PREVENT EQUIPMENT (flammable, caustic, etc.) unless the pump is PROBLEMS. To help recognize this information, observe the specifically designed and designated to handle them. following symbols: CAUTION ! Do not block or restrict discharge hose, as discharge hose may whip under pressure. IMPORTANT! Warns about hazards that can resul
Summary of the content on the page No. 4
SECTION: A- PUMP SPECIFICATIONS DISCHARGE: 1-1/2", (38) N.P.T. Female, Vertical. SEAL: Design: Single Mechanical, Oil-Filled LIQUID TEMPERATURE: Reservoir. Standard: 104°F (40°C) Continuous. Material: Rotating Faces - Ceramic High Temp: 200°F (93°C) Continuous. Stationary Faces - Carbon MOTOR HOUSING: Cast Iron ASTM A-48, Class 20 Min. Elastomer - Buna-N PUMP BODY: Hardware - 300 Series Stainless BP27, A, D & HT Cast Iron ASTM A-48, Class 20 Min. SPEED: 1550 RPM STRAINER:Standard: Polypropylen
Summary of the content on the page No. 5
SECTION B: GENERAL INFORMATION SECTION C: INSTALLATION B-1) To the Purchaser: C-1) Location: Congratulations! You are the owner of one of the finest These pumping units are self-contained and are ® pumps on the market today. Barnes Pumps are products recommended for use in a sump or basin. This pump is engineered and manufactured of high quality components. designed to pump rain water or light effluent, nonexplosive Over one hundred years of pump building experience and noncorrosive liquids and
Summary of the content on the page No. 6
TYPICAL INSTALLATION WITH WIDE ANGLE C-4) Electrical Connections: C-4.1) Power Cable: LEVEL CONTROL The cord assembly mounted to the pump must not be WALL SOCKET modified in any way. This pump comes complete with a 3 GFI wire cord and 3 prong grounded plug that must be connected into a 3 wire grounded Ground Fault receptacle. DO NOT remove ground pin from electrical plug. It is NOT recommended to use an extension cord with these pumps. Do not use the power cable to lift pump. DISCHARGE ⇒ C-4.2)
Summary of the content on the page No. 7
MODEL HP VOLT PH RPM NEMA FULL LOCKED CORD CORD CORD WINDING NO. (Nom) START LOAD ROTOR SIZE TYPE OD RESISTANCE CODE AMPS AMPS OHMS BP27 1/3 115 1 1550 E 9.9 15.5 16/3 SJTW-A 0.360 2.00/2.35 BP27A 1/3 115 1 1550 E 9.9 15.5 16/3 SJTW-A 0.360 2.00/2.35 BP27D 1/3 115 1 1550 E 9.9 15.5 16/3 SJTW-A 0.360 2.00/2.35 BP27HT 1/3 115 1 1550 E 9.9 15.5 16/3 SJTW-A 0.360 2.00/2.35 Winding Resistance ± 5% Pump rated for operation at ± 10% voltage at motor. Mercury Switch on BP27A, Cable 16/2, SJOW-A, 0.320 O
Summary of the content on the page No. 8
TABLE 1 - COOLING OIL - Dielectric SUPPLIER GRADE BP Enerpar Conoco Pale Paraffin 22 Mobile D.T.E. Oil Light G & G Circulating 22 Imperial Oil Voltesso-35 Shell Canada Transformer-10 Texaco Diala-Oil-AX Woco Premium 100 ECTION: E REPLACEMENT PARTS E-1 ORDERING REPLACEMENT PARTS: When ordering replacement parts, ALWAYS furnish the following information: 1. Pump MFG and Part numbers 2. Pump model number. 3. Part description. 4. Item part number. 5. Quantity required. 6. Shipping instructions. 7.
Summary of the content on the page No. 9
TROUBLESHOOTING CAUTION ! Always disconnect the pump from the electrical power source before handling. If the system fails to operate properly, carefully read instructions and perform maintenance recommendations. If operating problems persist, the following chart may be of assistance in identifying and correcting them: MATCH "CAUSE" NUMBER WITH CORRELATING "CORRECTION" NUMBER. NOTE: Not all problems and correction will apply to each pump model. PROBLEM CAUSE CORRECTION Pump will not run. 1. Poor
Summary of the content on the page No. 10
NOTES: 10
Summary of the content on the page No. 11
Fig. 4 11
Summary of the content on the page No. 12
PARTS LIST ITEM QTY. PART NO. DESCRIPTION 1 1 094449 Cord Set 1 34364H Cord Set BP27HT 2 1 30786 Handle 3 1 03200 Pipe Plug 1 14999 Pipe Plug BP27HT 4 1 29036 Upper Motor Housing 5 4 23469 Cap Screw 6 1 38156 Ground Screw 7 1 31241 Insulation Shield 8 1 29722 Motor 1 29722H Motor BP27HT 9 1 34157 Washer 10 1 29723 Bushing 11 1 32002 Washer 12 2 29926 Snap Ring 13 1 30198 Square Ring 14 1 29038 Lower Motor Housing 15 1 29726A Seal 1 29726H Seal BP27HT 16 1 31504 Strainer 17 1 59734H Body 18 4 213
Summary of the content on the page No. 13
IMPORTANT ! WARRANTY REGISTRATION Your product is covered by the enclosed Warranty. Complete the Warranty Registration Form and returned to Crane Pumps & Systems, Inc. Warranty Service Group IMPORTANT! If you have a claim under the provision of the warranty, contact your local Crane Pumps & Systems, Inc. Distributor. RETURNED GOODS RETURN OF MERCHANDISE REQUIRES A "RETURNED GOODS AUTHORIZATION". CONTACT YOUR LOCAL CRANE PUMPS & SYSTEMS, INC. DISTRIBUTOR. Products Returned Must Be Cleaned, Sa
Summary of the content on the page No. 14
® BARNES Limited Warranty We warrant to our immediate customer and to the ultimate consumer that products of our manufacture will be free of defects in material and workmanship under normal use and service for the following time periods, when installed and maintained in accordance with our instructions. Pump Products: One (1) year from date of installation or (24) twenty-four months from date of shipment, whichever occurs first. Cleaning Products: Twelve (12) months from date of installation or
Summary of the content on the page No. 15
IMPORTANT ! WARRANTY REGISTRATION Your product is covered by the enclosed Warranty. Complete the Warranty Registration Form and returned to Crane Pumps & Systems, Inc. Warranty Service Group IMPORTANT! If you have a claim under the provision of the warranty, contact your local Crane Pumps & Systems, Inc. Distributor. FOLD HERE ** IMPORTANT ! ** WARRANTY REGISTRATION CUSTOMER’S NAME DATE INSTALLED ADDRESS CITY STATE ZIP PHONE # FAX # DEALER’S NAME CITY STATE ZIP MODEL NO. SERIAL NO. PART NO. BRA
Summary of the content on the page No. 16
FOLD HERE AND TAPE, DO NOT STAPLE PLACE STAMP HERE CRANE PUMPS & SYSTEMS, INC. WARRANTY SERVICE GROUP 420 THIRD STREET P.O. BOX 603 PIQUA, OHIO 45356-0603 - U.S.A.
