Summary of the content on the page No. 1
3/4 HP DIRTY WATER SUBMERSIBLE
PUMP WITH FLOAT
94649
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, the product shown above may differ slightly from the actual product.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
®
Copyright © 2006 by Harbor Freight Tools . All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harb
Summary of the content on the page No. 2
Specifications Motor Min. Water Level 120 V, 60 Hz, 7 Amp 4” Pump Cord 18 Ft. - 3 Prong Plug Operating Temp. 95° F Discharge Size 1-1/2” Min. Switch Level 3” Discharge Fittings 1-1/2”, 1-1/4” and 1” Dimensions 6” Dia. x 13-1/2” H Delivery Height 26.6 Ft. Housing Material PP Plastic Flow Rate 3300 GPH Pump Weight 10.4 lb. Horsepower 3/4 HP Motor Drive Magnetic Drive Max. Particle Size 1” Warning: The pump should not be submerged in water deeper than the length of the power cord, which is 18 f
Summary of the content on the page No. 3
8. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically nonconductive clothes and nonskid footwear are recommended when working. Wear restrictive hair covering to contain long hair. 9. Use eye and ear protection. Always wear ANSI approved impact safety goggles. 10. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across electrical cables or frames. 11. Stay alert. Watch what you are doi
Summary of the content on the page No. 4
Unpacking When unpacking, check to make sure all parts are included. Refer to the parts list and as- sembly diagram on page 7 and 8. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual. Operation 1. Connect drain hose to the Universal Adapter (47) discharge fitting. This hose should be long enough to drain away from the reservoir being pumped. See installation examples on the next page. 2. If the pump needs to be lowered into a pool
Summary of the content on the page No. 5
Ground Fault Circuit Interrupter DANGER Electrical Connection ON H O 2 H O H O 2 2 H O 2 DANGER Never Touch Float (1) 1/8” HOLE or Water During Pump Operation Recommended Check Valve Removing Underground Water Accumulated From Rain Gutter ON H O H O 2 2 OFF ON - OFF Switch House Sump Operation SKU 94649 Page 5
Summary of the content on the page No. 6
Troubleshooting SYMPTOM CAUSE SOLUTION No power Check power source; Reset GFCI Impeller blocked Free impeller (see Maint.) The pump will not start Thermal protection shutdown Allow pump to cool down; auto restart Entangled Float Switch Check Float Switch Pump submerged too deep Reduce submersion depth Discharge pipe bent Free bends from pipe The pump operates but Suction grid clogged Clean suction grid pumps little or no water Air locked in suction base Turn off pump for 10 seconds Optional chec
Summary of the content on the page No. 7
Parts List Part Description Q’ty Part Description Q’ty 1 Float Switch 1 25 Screw 6 2 Power cable & plug 1 26 Press ring 1 3 Nut 2 27 O-ring 1 4 Plastic handle 1 28 Skeleton seal 3 6 Washer 3 29 Front cover 1 7 Screw 3 30 Front bushing 1 8 Outer pump housing 1 31 Bearing 1 9 Screw 1 32 Rotor 1 10 O-ring 2 33 Under washer 2 11 Rear housing motor 2 34 Stator 1 12 Cord Jacket 1 35 Spring washer 1 13 Cord clip 1 36 Screw 1 14 Cord clip 1 37 Earthing wire 1 15 Screw 1 38 Rear cover 1 16 Condenser 2 39
Summary of the content on the page No. 8
Assembly Drawing 47 20 18 17 19 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND
Summary of the content on the page No. 9
WARRANTY LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of ninety days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, or to lack of maintenance. We
