Summary of the content on the page No. 1
model t23084
5" pneumatic angle grinder
instruction manual
Copyright © DECEMBEr, 2010 By grizzly inDustrial, inC.
Warning: no portion of this manual may be reproduced in any shape
or form Without the Written approval of grizzly industrial, inc.
#ts13540 printED in China
Summary of the content on the page No. 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use. This responsibility includes but is not limited to
Summary of the content on the page No. 3
safety for your own safety read instruction manual before operating this equipment t he purpose of safety symbols is to attract your attention to possible hazardous conditions. t his manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. t he progression of symbols is described below. r emember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. in
Summary of the content on the page No. 4
7. avoid entanglements. Do not 16. do not force tool. it will do wear loose clothing, gloves, neck- the job better and safer at the rate ties, rings, bracelets, or other jewel- for which it was designed. ry, which may get caught in moving 17. checK for damaged parts parts, when operating this tool. Wear before using. Check for bind- a protective hair covering to contain ing and alignment of parts, broken long hair. parts, part mounting, loose bolts, 8. use correct air pressure. and any oth
Summary of the content on the page No. 5
INTRODUCTION Specifications Foreword The specifications, details, and Arbor Speed .........Variable 0–11,000 RPM 5 photographs in this manual represent Arbor Size .......................................... ⁄8"-11 the Model T23084 as supplied when the Grinding Wheel Diameter ........................ 5" 7 manual was prepared. However, owing to Grinding Wheel Bore .............................. ⁄8" Grizzly’s policy of continuous improvement, Grinding Wheel Type .............................. 27 1 c
Summary of the content on the page No. 6
operations t o change the grinding wheel: 1. DisConnECt grinDEr FroM air! 2. position the arbor wrench on the arbor flats behind the inner arbor flange (see figure 2). arbor Wrench r ead the manual before operation. become familiar with this tool, its safety instructions, and its operation before beginning any work. serious personal injury may result if safety Flange spanner or operational information is not Wrench understood or followed. figure 2. loosening the outer arbor changing gr
Summary of the content on the page No. 7
eye inJury lung /ear inJury hazard ! hazard ! Wear protective Wear protective equipment when equipment when using this tool. using this tool. accidental start hazard ! using grinder disconnect before service or tool always test the grinder on a scrap piece changes. of material similar to the workpiece to determine the ideal setup. air pressure hazard ! t o use the grinder: never exceed max psi rating for tool. 1. Make sure the workpiece is securely held in a vise or a similar devic
Summary of the content on the page No. 8
parts 44 22 28 1 49 27 25 3 23 2 24 22 26 21 4 6 5 7 33 35 8 36 9 34 20 37 10 11 46 47 12 32 13 30 43 48 14 31 45 16 38 39 40 15 41 29 17 42 19 18 REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PT23084001 MAIN HOUSING 26 PT23084026 ROTOR 2 PS79M PHLP HD SCR M3-.5 X 8 27 PT23084027 ROTOR BLADE 3 PT23084003 AIR OUTLET PLATE 28 PT23084028 ROTOR CYLINDER REAR CAP 4 PS68M PHLP HD SCR M6-1 X 10 29 PT23084029 HOUSING COUPLER 5 PT23084005 HANDLE 30 PT23084030 COUPLER NUT 6 PT23084006 O-RING 12.5MM 31 P
