Furuno 2837S user manual

User manual for the device Furuno 2837S

Device: Furuno 2837S
Category: Marine RADAR
Manufacturer: Furuno
Size: 5.12 MB
Added : 6/19/2013
Number of pages: 123
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Furuno 2837S. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Furuno 2837S.

For your convenience

If looking through the Furuno 2837S user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Furuno 2837S on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Furuno 2837S to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Furuno 2837S User manual - Online PDF
Advertisement
« Page 1 of 123 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Furuno 2837S but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Furuno 2837S. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1


MARINE RADAR/ARPA
FAR-2137S/2837S/2137S-BB
Installation Manual Comply with MSC.192(79)
TABLE OF CONTENTS
3.4 Adjustment Sweep Timing.................... 3-6
SAFETY INSTRUCTIONS....................... i
3.5 Suppressing Main Bang ....................... 3-7
EQUIPMENT LISTS .............................. iii
3.6 Other Settings ...................................... 3-8
SYSTEM CONFIGURATION.................. v
3.7 Dual Radar Display
(non IMO-type only) .......................... 3-16

Summary of the content on the page No. 2

The paper used in this manual is elemental chlorine free. ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN Telephone : +81-(0)798-65-2111 Fax : +81-(0)798-65-4200 A : APR. 2004 All rights reserved. Printed in Japan L : APR. 12, 2011 Pub. No. IME-35210-L (HIMA ) FAR-2137S/BB/2837S *00014868819* *00014868819* **00014868819 00014868819** * 0 0 0 1 4 8 6 8 8 1 9 *

Summary of the content on the page No. 3

SAFETY INSTRUCTIONS The operator and installer must read the applicable safety instructions before attempting to install or operate the equipment. Indicates a potentially hazardous situation which, if not avoided, will result in death or serious injury. DANGER Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. WARNING Indicates a potentially hazardous situation which, if not avoided, CAUTION can result in minor or moderate injury.

Summary of the content on the page No. 4

CAUTION WARNING Do not open the equipment Observe the following compass safe unless totally familiar with distances to prevent deviation of a electrical circuits and magnetic compass: service manual. Standard Steering compass compass Only qualified personnel ELECTRICAL should work inside the Antenna Unit SHOCK 3.95 m 2.55 m (30 kw) equipment. HAZARD Monitor Unit 1.55 m 1.00 m (MU-201CR) Construct a suitable service platform Monitor Unit 1.85 m 1.20 m (MU-231CR) from w

Summary of the content on the page No. 5

EQUIPMENT LISTS Standard Supply Name Type Code No. Qty Remarks SN30AF - 1 Radiator 200 VAC 3 φ 50 Hz, RSB-098 - 220 VAC 3 φ 60 Hz Antenna Chassis 380 VAC 3 φ 50 Hz, Antenna Unit RSB-099 - 1 440 VAC 3 φ 60 Hz RSB-100 - 220 VAC, 3 φ, 50 Hz Antenna Chassis RSB-101 - 220 VAC, 3 φ, 60 Hz for HSC RSB-102 - 440 VAC, 3 φ, 60 Hz Power Supply Unit PSU-007 - 1 MU-201CR For FAR-2137S MU-231CR For FAR-2837S Monitor Unit - 1 MU-190 For FAR-2137S MU-231 For FAR-2837S Processor Unit

Summary of the content on the page No. 6

Name Type Code No. Remarks For processor unit, RU-1803 - 440 VAC → 100 VAC For de-icer , 110/115/220/230 VAC RU-3305 - → 100 VAC For RSB-098/099, Transformer Unit RU-5693 - 110 V →220 VAC Not For RSB-098/099, RU-6522 - available 220 V →200 VAC for HSC For RSB-098/099, RU-5466-1 - 440 V →220 VAC Memory Card Interface Unit CU-200-FAR 000-081-568 W/CP03-27430, See chapter 4. External Buzzer OP03-21 000-030-097 Control Unit RCU-016 000-080-299 Remote type, W/FP03-09860 RA

Summary of the content on the page No. 7

SYSTEM CONFIGURATION Radiator SN30AF/ ANTENNA UNIT SN36AF Performance Monitor Chassis RSB-098/099 RSB-100/101/102 (for HSC) POWER SUPPLY UNIT PSU-007 RJB-001 ** * MONITOR UNIT MU-201CR or MU-190 (FAR-2137S) MU-231CR or MU-231 (FAR-2837S) CONTROL UNIT *** RCU-014 RU-5693 (Standard) *** or RU-6522 RCU-015 100-230 VAC RJB-001 ** (Trackball) *** RU-5466-1 Control Unit 1) EPFS RCU-016 IEC-61162 Serial Data PROCESSOR UNIT (Navigator) (Remote) (Input/Output) RPU-013 2) SDME IEC-61162 Serial Dat

Summary of the content on the page No. 8

About the category sticker This radar meets the requirements in IEC62388 (Marine navigation and radio communication equipment and systems-Shipborne radar-Performance requirements, method of testing and required test results). Check the appropriate box on the sticker which is pre-attached on the processor unit, according to your radar’s specification. Refer to the table shown below to confirm your category. Category Radar Type Antenna rotation speed FAR-2817, FAR-2827, FAR-2837S, FAR-

Summary of the content on the page No. 9

1. MOUNTING NOTICE Do not apply paint, anti-corrosive sealant or contact spray to coating or plastic parts of the equipment. Those items contain organic solvents that can damage coating and plastic parts, especially plastic connectors. 1.1 Antenna Unit Mounting considerations • The antenna unit is generally installed either on top of the wheelhouse, on the radar mast, or on a suitable platform. Locate the antenna unit in an elevated position to permit maximum target visibility. • A

Summary of the content on the page No. 10

1. MOUNTING • Install the antenna unit safely away from interfering high-power energy sources and other transmitting radio antenna. • Keep the lower edge of the antenna unit above the safety rail by 500 mm or more. • Two antenna units should be mounted as below: more than 20 more than 1 m • No funnel, mast or derrick should be within the vertical beamwidth of the antenna unit in the bow direction, especially zero degrees ±5°, to prevent blind sectors and false echoes on the radar pic

Summary of the content on the page No. 11

1. MOUNTING Installation precaution for S-band antenna unit If an S-band antenna unit is mounted near the end of a platform to provide sufficient rotation clearance for the radiator, the antenna unit, because of its weight, swings up and down by ship’s vibration and rolling. This exerts excessive levels of stress at the base of the radiator, which can damage the radiator. To prevent this, relocate the antenna unit, or if relocation is not possible, reinforce the platform. Mast for DF

Summary of the content on the page No. 12

1. MOUNTING Antenna unit assembling The antenna radiator and the antenna housing are shipped in separate packages. Assemble them as below. The antenna unit may be assembled before hosting it to the mounting platform. However, do not lift the antenna unit by the radiator. Antenna unit assembling procedure 1. Screw the guide pins (2 pcs.) in the radiator. 2. Remove the protective cap from the choke guide and radiator. 3. Grease O-ring and set it to the groove of the choke guide. 4. Pl

Summary of the content on the page No. 13

1. MOUNTING How to lift the antenna unit 1. Fix the antenna radiator to the antenna unit chassis as shown on page 1-4. 2. Attach the lifting fixtures and collars as shown below. 3. Position the radiator as shown below and arrange the ropes A and B. Lifting fixture Supplied as accessories. Remove after installation. Collar for fixing Spring washer Plat washer (M12) x20) Hex bolt (M12 (Torque 63.5Nm) Remove lifting fixture, coat threads of hex bolts with silicone grease, and then insert b

Summary of the content on the page No. 14

1. MOUNTING Fastening the antenna unit to the mounting platform See the figure on the next page for antenna unit mounting. 1. Referring to the antenna outline drawing, drill eight fixing holes of 15 mm in diameter in the radar mast platform or the deck. • The diameter of the mast for fixing the antenna unit platform must be over 250 mm. • The thickness of the antenna unit platform must be over 15 mm. • The reinforcement rib must be installed diagonally as shown below. Over 15mm Use t

Summary of the content on the page No. 15

1. MOUNTING Seal washer Corrosion proof rubber mat Use two nuts. (Torque 63.5Nm) Ground terminal G1_1/4-A Set corrosion-proof rubber mat, bolt antenna unit to mounting location, and coat exposed hardware with silicone sealant. Hex bolt Flat washer Flat washer Ground wire Spring washer Coat with silicone sealant after Hex nut fastening ground wire. Coat with silicone OR sealant. Ground wire Hex nut Spring washer Flat washer Hex bolt Ground wire Welding Antenna chassis Arrange ground terminal

Summary of the content on the page No. 16

1. MOUNTING 1.2 Monitor Unit The monitor unit can be flush mounted in a console panel, or mounted on a desktop using the optional accessories. For MU-190/231, see the applicable Operator’s Manual(s). Note: FAR-2137S-BB has no monitor unit. Prepare a suitable one locally. Recommended monitor: SXGA (1280x1024), aspect ratio 5:4 Mounting considerations When selecting a mounting location, keep in mind the following points: • Select a location where the display unit can be viewed conven

Summary of the content on the page No. 17

1. MOUNTING ± 506 1 4-FIXING HOLES ± 1 506 4-φ8 490 FIXING HOLES 534 30 80 Monitor unit MU-201CR (For FAR-2137S) 4-φ8 FIXING HOLES 570 ± 1 4-FIXING HOLES 554 570 ± 1 598 80 30 Monitor unit MU-231CR (For FAR-2837S) Flush mounting of monitor unit Panel hook Panel cover Fixing screw Attaching panel hook and panel cover Note: If you need to remove the monitor unit from the mounting panel, remove the four panel covers with your fingernail and use two panel hooks supplied as accessor

Summary of the content on the page No. 18

1. MOUNTING Contents of FP03-09820/09830 Name Type Code No. Qty Remarks Hanger L 03-163-1111 100-305-141 1 Hanger R 03-163-1112 100-305-181 1 03-163-1113 100-305-191 For FAR-2137S Hanger stay 1 03-163-2071 100-305-371 For FAR-2837S Hole plug CP-30-HP-13 000-160-074-10 2 Plastic rivet KB-13 Rivet Black 000-570-276-10 4 Hex. bolt M6x25 000-162-949-10 4 Hex. bolt M10x30 000-162-884-10 2 Spring washer M10 000-864-261 2 Flat washer M10 000-864-131 2 1. Assemble two hangers

Summary of the content on the page No. 19

1. MOUNTING The hand grip is optionally available for the desktop mounting monitor unit. Wave washer Rosette washer Screw M6x20 (Torque 7.6Nm) Handle Hood (option) When it is too bright in the daytime, use the optional hood to shade the screen. • For FAR-2137S: FP03-11500 (Code No.: 001-020-090) • For FAR-2837S: FP03-11000 (Code No.: 008-571-680) Contents of hood Name Type Code No. Qty. Remarks Hood (21) FP03-11501 001-020-120 1 For FAR-2137S Hood (23) FP03-11001 008-571-700

Summary of the content on the page No. 20

1. MOUNTING 1.3 Power Supply Unit The Power Supply Unit PSU-007 does not contain usual operating controls. Therefore, it can be installed in any recessed place either in vertical or horizontal position. (For the console mount display unit, the PSU-007 can be installed inside the console.) However, select a dry and well-ventilated location and observe the compass safe distance to prevent deviation of a magnetic compass. See page ii. 1. Open the cover of the power supply unit. 2. Fas


Alternative user manuals
# User manual Category Download
1 Furuno 1623 User manual Marine RADAR 496
2 Furuno 1712 User manual Marine RADAR 91
3 Furuno 1720 User manual Marine RADAR 299
4 Furuno 1730 User manual Marine RADAR 47
5 Furuno 1731 User manual Marine RADAR 76
6 Furuno 1750 User manual Marine RADAR 24
7 Furuno 1715 User manual Marine RADAR 168
8 Furuno 1622 User manual Marine RADAR 200
9 Furuno 1751 User manual Marine RADAR 51
10 Furuno 1824C-BB User manual Marine RADAR 29
11 Furuno 1830 User manual Marine RADAR 125
12 Furuno 1831 User manual Marine RADAR 99
13 Furuno 1832 User manual Marine RADAR 128
14 Furuno 1834C-BB User manual Marine RADAR 25
15 Furuno 1930 User manual Marine RADAR 34
16 ACR Electronics Nauticast 2607 User manual Marine RADAR 2
17 ACR Electronics Nauticast Y1-03-0203 User manual Marine RADAR 1
18 ACR Electronics PATHFINDER 2714 User manual Marine RADAR 5
19 ACR Electronics NAUTICAST Y1-03-0212-1 User manual Marine RADAR 7
20 ACR Electronics Nauticast 2662 User manual Marine RADAR 8