Summary of the content on the page No. 1
Installation instructions
™
Spacemaker
for your new
Laundry
WSM2780 Gas
Before you begin – Read these instructions completely and carefully.
IMPORTANT – OBSERVE ALL GOVERNING CODES AND ORDINANCES.
Note to Installer – Be sure to leave these instructions with the Consumer.
Note to Consumer – Keep these instructions with your Owner’s Manual for future reference.
POTENTIAL FIRE AND SHOCK HAZARD
WARNING –
• Use only rigid metal or flexible metal 4″ diameter ductwork inside the dryer cabinet or for ex
Summary of the content on the page No. 2
Installation Instructions ™ ™ UNPACKING SPACEMAKER UNPACKING SPACEMAKER (CONT.) Remove tape and two corner pads from rear NOTE: The tub blocking pad, shipping bolt and plastic 1 bottom corners of appliance. spacer should be retained for use if the appliance is transported at a later date. Using the four shipping corner posts, lay the 2 appliance on its left side so the shipping base does Remove clips holding the following: 8 not rest on the floor. a. inlet hoses Shipping Shipping b. drain hose
Summary of the content on the page No. 3
Installation Instructions ™ MOVING SPACEMAKER TO OPERATING CONNECTING TO PLUMBING FACILITIES LOCATION CAUTION: Be sure water supply lines have been thoroughly flushed to remove particles that might Remove the 2 screws securing the access panel 11 clog the washer filter screens. to the dryer cabinet. Lift the front access panel until the tabs can be disengaged from the dryer Check inlet hoses to insure the rubber washers 13 cabinet and remove the panel. are installed in each end. (If your laundry
Summary of the content on the page No. 4
Installation Instructions CONNECTING TO GAS SUPPLY CHECKING APPLIANCE OPERATION Connect the gas supply to the dryer. If codes Make sure all packing and shipping materials are 14 16 allow, use new flexible metal tubing (design removed, including the washer shipping bolt and certified by the American Gas Association). Be plastic spacer block. sure there are no kinks. For gas connections, you Make sure the drain hose is properly routed—not 17 MUST use pipe joint compound resistant to the coiled or
Summary of the content on the page No. 5
Installation Instructions PLUMBING INFORMATION ELECTRICAL CONNECTION INFORMATION WATER SUPPLY REQUIREMENTS CAUTION: • HOT AND COLD WATER FAUCETS – Must be within 42″ For personal safety: of the appliance water inlet hose connections. The TURN OFF ELECTRICITY AT POWER SOURCE (CIRCUIT faucets must be 3/4″ garden hose-type so inlet BREAKER/FUSE BOX) BEFORE INSTALLING OR hoses can be connected. SERVICING THIS APPLIANCE. • WATER PRESSURE – Must be between 10 and 120 DO NOT USE AN EXTENSION CORD WIT
Summary of the content on the page No. 6
Installation Instructions GAS CONNECTION INFORMATION EXHAUST CAUTION: EXHAUST DUCT LENGTH INFORMATION Do not attempt to alter gas orifice or adjust burner air • The MAXIMUM ALLOWABLE length of the exhaust shutter. Natural gas input may vary in some areas from system depends upon the type of duct, number of 700 to 1200 B.T.U. per cubic foot. If the gas orifice or turns, the type of exhaust hood (wall cap) and all burner air shutter is incorrectly adjusted, serious conditions noted below. The ma
Summary of the content on the page No. 7
Installation Instructions EXHAUST (CONT.) MOBILE HOME INSTALLATION • Installation must conform to Manufactured Home SEALING OF JOINTS Construction and Safety Standard, Title 24 CFR, • All joints should be tight to avoid leaks. Part 32-80. NOTE: The male end of each section of duct must point • The dryer must be exhausted to the outside with away from the dryer. the termination securely fastened to the mobile home structure. • Do not assemble ductwork with fasteners that extend into the duct.
Summary of the content on the page No. 8
Installation Instructions MISCELLANEOUS REQUIREMENTS WARNING – For your safety, the information in this manual must LOCATION be followed to minimize the risk of fire or explosion or to • The appliance must be installed on firm flooring to prevent property damage, personal injury or loss of life. minimize vibration during spin cycles. Concrete flooring • Do not store or use gasoline or other flammable vapors is best; but wood base is sufficient, providing the floor and liquids in the vicinity of
