Chevrolet 6405/4410TK user manual

User manual for the device Chevrolet 6405/4410TK

Device: Chevrolet 6405/4410TK
Category: Window
Manufacturer: Chevrolet
Size: 0.33 MB
Added : 9/2/2013
Number of pages: 5
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Chevrolet 6405/4410TK. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Chevrolet 6405/4410TK.

For your convenience

If looking through the Chevrolet 6405/4410TK user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Chevrolet 6405/4410TK on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Chevrolet 6405/4410TK to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Chevrolet 6405/4410TK User manual - Online PDF
Advertisement
« Page 1 of 5 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Chevrolet 6405/4410TK but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Chevrolet 6405/4410TK. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

POWER VISION
INSTALLATION INSTRUCTIONS


Models: 6405/4410 & 6405/4410TK GM/Chevrolet 2007 – current (new body style) full size trucks and
SUVs with manual power mirrors.

THIS SET IS DESIGNED FOR TRUCK WITH STOCK MANUAL MIRRORS. IF YOU
CURRENTLY HAVE POWER MIRRORS, THE WRONG SET HAS BEEN ORDERED.

Caution! - Do not attempt to manually extend or retract the mirrors. They should be moved under their own
motor power only.

Tools required for the installation are: 7mm and 1

Summary of the content on the page No. 2

6405/4410 Install PAGE 2 5. The door trim panels have a series of snaps around the outer edges. Unsnap the door trim panel. 6. Remove the door trim panel: Release the door handle cable by compressing the cable lock with needle nose pliers (as shown), rotate until ball lines up with the slot, then lift upward. Remove the trim panel. 7. Support the stock mirror while removing the 3 mirror mount lug nuts using a 10mm socket. Save the stock nuts for later in

Summary of the content on the page No. 3

6405/4410 Install PAGE 3 4. Insert the studs provided (3 for each side) with the tapered end out (see diagram E). They should screw into the mount up to the stop line – approx. 1cm or 3/8 of an inch. Next, line up the mount with the stock gasket and apply the mount to the door. While supporting the mirror add the stock nuts. Tighten the stock nuts to 70 inch pounds. This gasket is necessary for sealing against moisture and wind noise and to keep from metal to metal contact. (Hint,

Summary of the content on the page No. 4

6405/4410 Install PAGE 4 4. Repeat steps 1 through 3 for the passenger side identifying the right side active turn signal wire (recommend trying dark blue w/white tracer wire) and tapping the passenger mirror into it using a scotchlok. 5. Take the black wire from inside the driver side two-strand harness that you have run into the cab and the black wire from the passenger side and crimp them together in the ring terminal provided. The turn signal system can then be grounded under

Summary of the content on the page No. 5

6405/4410 Install Page 5 2. The next step is to run the main harness. Pop off both ends of the boot located between the door and cab. The main wiring harness has black and red wires attached. Remove the rubber band to uncoil the harness. One end of the main harness has a 12 pin and a 6 pin connector – this end stays inside the driver’s door. To run the main harness, start by fishing the passenger's side end of the harness (the one with just a 6 pin connector) through the driver's door


Alternative user manuals
# User manual Category Download
1 Chevrolet 6405/4410 User manual Window 0
2 Chevrolet Power Vision User manual Window 0
3 Adobe 8 User manual Window 1
4 Chevrolet 6405/4410 User manual Window 0
5 Chevrolet Power Vision User manual Window 0
6 Crane Merchandising Systems 480 User manual Window 1
7 Dell NT User manual Window 0
8 Dell 2000 User manual Window 1
9 Dell PowerEdge Cluster SL300 User manual Window 1
10 Dell PowerEdge Cluster SE300 User manual Window 0
11 Directed Electronics PN 904100 User manual Window 0
12 Friedrich SC User manual Window 0
13 Grizzly 1553 User manual Window 0
14 Grizzly 1551 User manual Window 1
15 Grizzly 1554 User manual Window 2