Fisher-Price M7332 user manual

Summary of the content on the page No. 1

M7332
www.fi sher-price.com

Summary of the content on the page No. 2

Consumer Information • Please keep this instruction sheet for future reference, as it WARNING contains important information. • Adult assembly is required. To avoid serious injury: • Tools needed for assembly: Hammer, Phillips Screwdriver • Adult supervision is required. and Scrap Block of Wood (not included). • Never use near cars and other motor • Age: 2 - 6 years; Weight Limit: 60 lbs (27 kg). vehicles, near streets, steps, sloped drive- • Please save all packaging material until assembly i

Summary of the content on the page No. 3

Parts Note: Some parts shown are assembled to both sides of the trike. Handlebar Seat Cap Seat Retainer Fork Straight Axle Rear Wheel 2 Hubcaps 2 Covers 2 Fork Covers Frame Cap Nut 2 Pedals Pedal Axle Cap Nut Assembly Tool Front Wheel 4 Pedal Hubs Part Not Shown: Label Sheet 3

Summary of the content on the page No. 4

Assembly Rear Wheel Indented Side Up Cap Nut Hubcap Straight Axle Frame Cover Hubcap Rear Wheel Indented Side Down Hubcap Assembled Straight Axle Rear Wheel 1 Cap Nut 3 Assembly Tool • Slide a hubcap (peg side up) onto the straight axle. • Slide a rear wheel (indented side down) onto the • Place a scrap block of wood on a flat surface. straight axle. • Turn the frame on its side with the exposed end of the straight axle up. • Place the cap nut assembly tool under the assembled rear wheel and

Summary of the content on the page No. 5

Assembly Pedal Hub Tab Pedal Hub Pedal Axle Pedal Axle Tab Slot Pedal Hub 4 Pedal Hub • Fit two pedal hubs onto the pedal axle tabs. Make sure the tabs fit into the slot in each pedal hub. Pedal Hubs 6 Pedal Axle • Turn the front wheel assembly over. Front Wheel • Insert a pedal hub onto the top of the pedal axle and into the hole in the center of the front wheel. • Insert the remaining pedal hub below the pedal axle and Hole into the hole in the center of the front wheel. • Push the pedal h

Summary of the content on the page No. 6

Assembly Fork Arms Fork Cover Cap Groove 8 Pedal Axle 10 • Place the front wheel assembly between the fork arms. Make sure the pedal axle fits into the groove at the bottom • Insert and “snap” the cap into the hole in the frame. of each fork arm. • Place a fork cover over the pedal axle on one fork arm. 3 • Insert two #8 x / " screws through the fork cover and into 4 the fork arm. Tighten the screws with a Phillips screwdriver. Seat Retainer Do not over-tighten. • Repeat this procedure to a

Summary of the content on the page No. 7

Label Decoration Attaching the Seat Helpful Hint: The seat can be attached to the frame in any of three positions, depending on the size of your child. Check 1 your child’s fit on the trike by observing the seat to pedal distance, as it is being ridden. If the pedals seem too far away or too close for your child, move the seat up or down. 2 3 6 Seat Tabs Seat Retainer 4 5 (Label on other side) 7 7 • Make sure the areas where the labels will be applied are Slots clean and dry. Wipe your vehi

Summary of the content on the page No. 8

Removing the Seat Care • Periodically, check the plastic parts and if broken or cracked, dispose of them properly. Seat • Check all fasteners regularly to be sure they are tight. If the fasteners are not tight, tighten them as necessary. • To clean, use a mild soap and water solution and a clean cloth. Rinse clean with water to remove soap residue. Seat Retainer Tab Frame Seat Retainer Tab • Turn the frame on it’s side. • Squeeze the seat retainer tabs toward one another and lift the seat f