Summary of the content on the page No. 1
14/15 GAUGE ANGLE FINISH
NAILER KIT
MODEL G6049
INSTRUCTION MANUAL
COPYRIGHT © MAY, 2002 BY GRIZZLY INDUSTRIAL, INC.
1821 VALENCIA ST., BELLINGHAM, WA 98227
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN TAIWAN
ONLINE MANUAL DISCLAIMER
THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS CUR-
RENTLY BEING SHIPPED. THE MACHINE CONFIGURATION CAN CHANGE AS PRODUCT IMPROVEME
Summary of the content on the page No. 2
SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progres- sion of symbols is described below. Remember that safety messages by them- selves do not eliminate danger and are not a substitute for proper accident pre- vention measures. Indica
Summary of the content on the page No. 3
Safety Instructions For Pneumatic Tools 10. USE PROPER AIR HOSE for the 18. DISCONNECT TOOLS before ser- tool. Make sure your air hose is in vicing and changing accessories. good condition and is long enough to 19. USE THE RECOMMENDED reach your work without stretching. ACCESSORIES. Consult the owner’s manual for recommended 11. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neck- accessories. The use of improper ties, rings, bracelets, or other jewel- accessories may cause risk of ry
Summary of the content on the page No. 4
Basic Nailer Safety In addition to the rules stated in the previ- ous section, and those in the warning boxes throughout this manual, please observe the following safety tips for your new nailer: 1. READ THIS ENTIRE MANUAL BEFORE OPERATING THE NAIL- ER. 2. ALWAYS DISCONNECT AIR FROM THE NAILER whenever servicing or Operating this nailer can propel installing nails. During maintenance, objects into the air, causing immedi- a nailer connected to air may fire acci- ate eye damage. To protect yourse
Summary of the content on the page No. 5
INTRODUCTION Most important, we stand behind our tools. Commentary If you have any service questions or parts We are proud to offer the Grizzly Model requests, please call or write us at the G6049 14/15 Gauge Angle Finish Nailer. location listed below. This model is part of a growing Grizzly family of fine power tools. When used Grizzly Industrial, Inc. according to the guidelines set forth in this 1203 Lycoming Mall Circle manual, you can expect years of trouble- Muncy, PA 17756 free, enjoyable
Summary of the content on the page No. 6
Compressed Air System Safety Yoke Mechanism The Model G6049 is designed to be oper- A safety yoke mechanism (bump fire) on ated at 80-120 psi. Do not exceed the the nose of the nailer acts as a safety maximum operating pressure! device. When the trigger is pressed, the nailer will not fire until the safety yoke Before you use your new nailer, regulate mechanism is depressed. the air pressure on your air compressor to barely over the minimum psi for your nail- Before you use your nailer for the f
Summary of the content on the page No. 7
OPERATION Single/Bump Fire Mode Loading Nailer The Model G6049 is equipped with a sin- To load your nailer: gle/bump fire trigger. 1. Disconnect the air supply from the To select single or bump fire operation: nailer! 2. Load nails at the top of the magazine 1. Disconnect the air supply from the in the T-slot as shown in Figure 1. nailer! 2. Locate the hex nut that secures the safety yoke mechanism to the trigger housing. See Figure 2. 3. To select Single Fire mode, tighten the hex nut complete
Summary of the content on the page No. 8
Besides damaging your workpiece, Operating Nailer deflection can cause injury if your free If you have not read the safety instruc- hand is securing the workpiece in the tions in this manual, do not operate the location that the nail deflects. nailer. 4. Press the trigger. If the nail drove into the wood far enough, continue with Periodically, place one drop of the included your intended operations. If the nail oil into the quick connect fitting where the either went too far or not far enough, n
Summary of the content on the page No. 9
To clear a jammed nail from the discharge Clearing Jammed Nails area with the Model G6049: The most frequent situation with any type of nailer is a nail jam. A jammed nail must 1. Disconnect the nailer from the air be cleared before using the nailer again. supply! 2. Push the finger tab inside the maga- zine pusher, pull the pusher back slightly to clear it from the nail stick and allow it to come all the way for- ward, near the nose. 3. Push down the backstop inside the magazine and slide the n
Summary of the content on the page No. 10
Oiling Nailer Cleaning Nailer The Model G6049 is considered an oil-less Use a good solvent to clean the nose assembly of the nailer. Always be sure that model. This means it features a teflon pis- the nailer is dry before using it again. ton ring that does not require oil to operate. However, periodic applications of oil will Do not allow dust, chips, sand, etc. into the extend the useful life of the piston assem- air connectors or into the body of the nail- bly. er; this may result in leaks an
Summary of the content on the page No. 11
Replacing Pistons/O-Rings If you use your nailer day in and day out, Grizzly offers repair pistons as cheap insurance against wasted down time and lost profits in the event that a piston or pis- ton shaft becomes worn out. To replace a piston: Figure 7. Removing nailer exhaust cap. 8. With a long flathead screwdriver or similarly shaped tool, push the piston shaft back inside the nailer until you can grip the piston head and remove it from the cylinder. (Be careful not to scratch the discharge a
Summary of the content on the page No. 12
G6049 PART BREAKDOWN -11- G6049 14/15 Gauge Angle Finish Nailer Kit 48A 7A 92 2 15A 3 5A 26 7 6 92A 18 25 8 19 9 20 27 72 28 70 71 74 10 21 31 11 36 29 33 32 12 37 30A 38 58 13 20 34 57 59 60 39 56A 69 14 40 22 50 49 5 51 52A 67A 46 23 54 64 35A 41 53 43 24 68A 55 83 69 60 62 42 90 47A 66A 44 92A 93 69 69 1 65 88 63 76A 76A 86 77 76A 16A 45B 29-1
Summary of the content on the page No. 13
REF PART # DESCRIPTION REF PART # DESCRIPTION 01 P6049001 LOCK NUT 42 P6049042 PLUNGER 02 P6049002 EXHAUST COVER 43 P6049043 O-RING 03 P6049003 SPRING PLATE 44 P6049044 PLUNGER CAP 05A P6048005A CAP SCREW SW 45B P6048045B TRIGGER ASSEMBLY 06 P6049006 CAP 46 P6049046 O-RING 07A P6048007A BUTTON HD CAP SCR 47A P6044047A O-RING 08 P6049008 SPACER 48A P6049048A LATCH 09 P6049009 PISTON STOPPER 49 P6048049 BALL PIN 10 P6049010 SPRING 50A P6049050A GUIDE COVER ASM 11 P6049011 O-RING 50 P6049050 NOSE C
Summary of the content on the page No. 14
TROUBLESHOOTING PROBLEM CAUSE ACTION Air leaking at trigger valve 1. O-rings in trigger valve 1. O-rings must be replaced housing are damaged. & operation of safety area. yoke must be checked. Air leaking between hous- 1. Loose screws in housing. 1. Tighten screws. ing and hose. 2. Damaged O-ring. 2. Replace O-ring. 3. Loose air fitting. 3. Tighten air fitting. Air leaking between hous- 1. Damaged seal. 1. Replace damaged seals. ing and cap assembly. 1. Air leaks. 1. Tighten screws and fit- Tool
Summary of the content on the page No. 15
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance. This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are here- by limited to
Summary of the content on the page No. 16
WARRANTY CARD Name__________________________________________________________ Street__________________________________________________________ City____________________State________Zip_________ Phone Number____________E-Mail___________________FAX____________ Model #_______________Serial#________________Order #______________ The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of course, all information is s
Summary of the content on the page No. 17
Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT NAIL
