MTD E2B5 & E295 user manual

User manual for the device MTD E2B5 & E295

Device: MTD E2B5 & E295
Category: Snow Blower
Manufacturer: MTD
Size: 3.99 MB
Added : 9/21/2014
Number of pages: 32
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for MTD E2B5 & E295. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with MTD E2B5 & E295.

For your convenience

If looking through the MTD E2B5 & E295 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual MTD E2B5 & E295 on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual MTD E2B5 & E295 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
MTD E2B5 & E295 User manual - Online PDF
Advertisement
« Page 1 of 32 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual MTD E2B5 & E295 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to MTD E2B5 & E295. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

Safety • Setp Up • Operation • Adjustments • Maintenance • Troubleshooting • Parts Lists • Warranty
OPERATOR’S MANUAL
Models 2B5 & 295
Models E2B5 &E295
Single-Stage Snow Thrower
IMPORTANT
READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-
covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting appl

Summary of the content on the page No. 2

This Operator’s Manual is an important part of your new snow thrower. It will help you assemble, prepare and maintain the unit for best performance. Please read and understand what it says. Table of Contents Safety Labels ...................................................... 3 Adjustments & Maintenance ........................... 10 Safe Operation Practices ................................... 4 Off-Season Storage .......................................... 12 Setting Up Your Snow Thrower ....

Summary of the content on the page No. 3

1 Safety � � � � � � � � � �� � � � � � � � � ��� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � Labels � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � ����������������������� � ����� � ������ � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � ������������������������������

Summary of the content on the page No. 4

WARNING: Engine Exhaust, some of its constituents, and certain vehicle compo- nents contain or emit chemicals known to State of California to cause cancer and birth defects or other reproductive harm. 2 DANGER: This machine was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating hands and feet and throwing objects

Summary of the content on the page No. 5

Operation Maintenance & Storage 1. Do not put hands or feet near rotating parts, in the 1. Never tamper with safety devices. Check their proper auger/impeller housing or chute assembly. Contact with the operation regularly. Refer to the maintenance and rotating parts can amputate hands and feet. adjustment sections of this manual. 2 2. The auger/impeller control lever is a safety device. Never 2. Before cleaning, repairing, or inspecting machine bypass its operation. Doing so makes the machin

Summary of the content on the page No. 6

WARNING: Disconnect the spark plug wire and ground it against the engine to prevent unintended starting. � 3 Positioning the Upper Handle 1. Remove packing material, if present. Snow 2. Raise the upper handle in the direction shown in � Thrower Figure 1 until it clicks into the operating position. Make sure not to pinch or crimp the cable. Setup � 3. Tighten the knobs. Figure 1 Assembling the Discharge Chute NOTE: This Operator’s For shipping reasons, the snow thrower has been Manual c

Summary of the content on the page No. 7

�������������������� �������������� 4 ��� Know ������ ���������������� Your Snow �������������������� ������������ Thrower �������������� ����������� WARNING Be familiar with all the controls on ����������������� ����������� the snow thrower �������� and their proper ����� operation. Know how to stop the machine Figure 4 and disengage them Choke Lever Auger quickly. Activating choke control closes the choke plate on When engaged, the augers rotation draws snow into the carburetor an

Summary of the content on the page No. 8

Before Starting ������������������� � 1. The spark plug wire was disconnected for safety. Attach spark plug wire to spark plug before starting. �������������� IMPORTANT: For complete and detailed engine 5 starting, stopping and storing instructions, it is recommended that you read the engine manual also ������ Operation included with this unit. �� � �������� Gas and Oil Fill-Up ��� 1. Check oil and gasoline level and add if necessary. Follow related instructions in the separate engine ��

Summary of the content on the page No. 9

To Stop Engine Operating Tips 1. To stop engine, turn ignition key counter-clockwise. 1. Discharge snow downwind whenever possible. Disconnect the spark plug wire from the spark plug Slightly overlap each previously cleared path. to prevent accidental starting while equipment is 2. Lifting up on the handle will allow the rubber on the 5 unattended. augers to propel the snow thrower forward. Pushing To help prevent possible freeze-up of starter, downward on the handle will raise the augers of

Summary of the content on the page No. 10

WARNING: NEVER attempt to make Shave Plate any adjustments while the engine is 1. To check the adjustment of the shave plate, place the running, except where specified in the unit on a level surface. The wheels, shave plate and operator’s manual. augers should all contact level surface. Note that if the 6 shave plate is adjusted too high, snow may blow under the housing. If the shave plate wears out excessively, or the unit does not self-propel, the shave plate may Adjustments be too l

Summary of the content on the page No. 11

Replacing Belt WARNING: Before servicing, repairing, or inspecting, disengage the control bail and stop engine. Wait until all 6 moving parts have come to a complete stop. Disconnect spark plug wire and � � � � �� � � � � � � ground it against the engine to prevent Adjustments unintended starting. & Remove the belt cover by removing five hex screws. See Figure 9. Then simply pull the belt off by grasping it from Maintenance the bottom of the auger pulley and pulling off. Once you remov

Summary of the content on the page No. 12

Observe the following, when preparing your snow thrower for off-season storage: • Drain fuel into an approved container outdoors, away from any open flame. Allow engine to cool. Extin- 7 guish cigarettes, cigars, pipes and other sources of ignition prior to draining fuel. Fuel left in engine during warm weather deteriorates and will cause Off-Season serious starting problems. • If unit is to be stored over 30 days, prepare for Storage storage as instructed in the separate engine manual pa

Summary of the content on the page No. 13

Problem Cause Remedy 1. Choke not in ON position. 1. Move choke to ON position. Engine fails to start 2. Spark plug wire disconnected. 2. Connect wire to spark plug. 8 3. Fuel tank empty or stale fuel. 3. Fill tank with clean, fresh gasoline. 4. Engine not primed. 4. Prime engine as instructed in “Operating Your Snow Thrower”. Trouble- 5. Clean, adjust gap, or replace. 5. Faulty spark plug. 6. Clean fuel line. Shooting 6. Blocked fuel line. 7. Insert key fully into the switch. 7. Safety key no

Summary of the content on the page No. 14

Model/Modèle 2B5-295 �� �� �� � �� � �� �� � �� � �� � �� �� �� �� �� �� �� � �� �� �� � �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� � �� �� �� � �� �� �� �� NOTE: Snow thrower features/components vary by model. NOT all parts listed above and pictured on the previous page are standard equipment. REMARQUE: Les caractéristiques/composants des souffleuses varient d’un modèle à un autre. Les pièces énumérées ci-dessus et illustrées sur la page précédente ne sont pas TOUTES fournies

Summary of the content on the page No. 15

Model/Modèle 2B5-295 REF PART NO. NO. 9 N° DE N° DE RÉF PIÈCE DE SCRIP TION DE SCRIP TION 1 629-0071 Extension Cord 10 Ft. Corde à ralonge de 10 pi de lg. Illustrated 2 710-0409 Hex Bolt 5/16-24 x 1.75 Boulon hex. 5/16-24 x 1,75 3 710-0627 Hex L-Bolt 5/16-24 x .75 Gr. 5 Boulon hex 5/16-24 x 0,75 Qual. 5 Parts/ 4 710-0654A Hex Wash HD Tap Scr 3/8-16 x .88 Vis autotaraudee 3/8-16 x 0,88 5 710-0751 Hex Bolt 1/4-20 x .62 Gr. 5 Boulon hexagonale 1/4-20 x 0,62 Qual. 5 o 6 710-1003 Hex Wash B-Tapp Sc

Summary of the content on the page No. 16

Model/Modèle 2B5-295 �� �� �� �� �� �� �� �� � � 10 � � �� �� �� �� � �� �� � �� � �� �� �� �� �� � �� �� 10 �� � �� �� �� �� �� �� �� �� �� �� �� 16

Summary of the content on the page No. 17

Model/Modèle 2B5-295 9 REF PART NO. NO. N° DE N° DE Illustrated RÉF PIÈCE DES CRIPT ION DES CRIPT ION 1 684-04127 Lower Chute Ass’y (Incl. #37-40) Ensemble de la goulotte inf. comp. les nos. 37 ou 40) Parts/ 2 710-04071 Carriage Screw 5/16-18 x 1.0 Boulon ordinaire 5/16-18 x 1,0 3 710-0451 Carriage Bolt 5/16-18 x .75 Boulon ordinaire 5/16-18 x 0,75 Pièces 4 712-04063 Flange Locknut 5/16-18 Gr. F, Ny lon Contre-écrou à embase 5/16-18 Qual. F, ny lon 6 731-04388A Chute Han dle Poignée - goulot

Summary of the content on the page No. 18

MANUFACTURER’S LIMITED WARRANTY The limited warranty set forth below is given by MTD LLC with respect d. Service completed by someone other than an authorized service to new merchandise purchased and used in the United States and/or its dealer. territories and possessions, and by MTD Products Limited with respect to e. MTD does not extend any warranty for products sold or exported new merchandise purchased and used in Canada and/or its territories and outside of the United States and/or

Summary of the content on the page No. 19

GARANTIE DU FABRICANT POUR: d. L’entretien ou les réparations effectués par quiconque autre qu’une La garantie limitée qui est énoncée ci-dessous est offerte par MTD LLC station technique agréée. pour toutes les marchandises neuves achetées et utilisées aux États- Unis, dans ses possessions et territoires, et par MTD Products Limited, e. MTD ne garantit pas les produits vendus ou exportés hors des États- pour toutes les marchandises achetées et utilisées au Canada et/ou ses Unis et/ou du Can

Summary of the content on the page No. 20

Problème Cause(s) Solution Le moteur ne démarre pas 1. Volet de départ fermé. 1. Ouvrez le volet de départ. 2. Fil de la bougie débranché. 2. Branchez le fil de la bougie. 8 3. Réservoir vide ou essence éventée. 3. Faite le plein avec une essence propre et fraîche. 4. Bouton de l’amorceur n’étant pas employé 4. Consultez le chapitre “Utilisation de la Dépannage correctement. Souffleuse”. 5. Bougie défectueuse. 5. Nettoyez, réglez l’écartement ou remplacez la bougie. 6. Canalisation de ca


Alternative user manuals
# User manual Category Download
1 MTD 150 User manual Snow Blower 94
2 MTD 190-469A User manual Snow Blower 6
3 MTD 190-032-101 User manual Snow Blower 23
4 MTD 179cc User manual Snow Blower 21
5 MTD 200 User manual Snow Blower 12
6 MTD 199-658 User manual Snow Blower 1
7 MTD 191-768 User manual Snow Blower 1
8 MTD 235 User manual Snow Blower 2
9 MTD 190-768 User manual Snow Blower 0
10 MTD 208cc User manual Snow Blower 57
11 MTD 230, S230, 240, S240, 250, S250, 260, S260, 261, S261 User manual Snow Blower 5
12 MTD 230 User manual Snow Blower 0
13 MTD 240 User manual Snow Blower 16
14 MTD 250 User manual Snow Blower 8
15 MTD 285 User manual Snow Blower 0
16 Agri-Fab 45-0402 User manual Snow Blower 2
17 Agri-Fab 45-0418 ATV User manual Snow Blower 1
18 Agri-Fab 45-0418 User manual Snow Blower 1
19 Alliance Laundry Systems DRYING TUMBLERS 70269501R3 User manual Snow Blower 2
20 Ariens 924 SNO-THRO 924109 User manual Snow Blower 60