Summary of the content on the page No. 1
90550129 PC1800D 4/1/09 2:37 PM Page 1
18v 1/2 inch (13mm)
Cordless Drill/Driver
Perceuse-visseuse sans fil de
18v et 13 mm (1/2 po)
Taladro/destornillador
inalámbricos de 13 mm
(1/2 pulgadas) y 18v
Instruction manual
Manuel d'instructions
Manual de'instrucciones
www.portercable.com
INSTRUCTIVO DE OPERACIÓN,
CENTROS DE SERVICIO Y PÓLIZA DE
GARANTÍA.
ADVERTENCIA: LÉASE ESTE
INSTRUCTIVO ANTES DE USAR EL
PRODUCTO.
CATALOG NUMBER
PC1800D
8 10 12 14
Summary of the content on the page No. 2
90550129 PC1800D 4/1/09 2:38 PM Page 2 General Power Tool Safety Warnings : Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. 1) Work area safety a) Keep work area clean and well lit. Cluttered or dark areas i
Summary of the content on the page No. 3
90550129 PC1800D 4/1/09 2:38 PM Page 3 The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures r
Summary of the content on the page No. 4
90550129 PC1800D 4/1/09 2:38 PM Page 4 : ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use face or dust mask if drilling operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT: • ANSI Z87.1 eye protection (CAN/CPA Z94.3), • ANSI S12.6 (S3.19) hearing protection, • NOSH/OSHA respiratory protection. : Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the state of California to cause can
Summary of the content on the page No. 5
90550129 PC1800D 4/1/09 2:38 PM Page 5 • When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord. Recommended Minimum Wire Size for Extension Cords Total L
Summary of the content on the page No. 6
90550129 PC1800D 4/1/09 2:38 PM Page 6 • DO NOT attempt to charge the battery pack with any chargers other than the ones in this manual. The charger and battery pack are specifically designed to work together. • These chargers are not intended for any uses other than charging designated PORTER-CABLE rechargeable batteries. Any other uses may result in risk of fire, electric shock or electrocution. • Do not expose charger to rain or snow. • Pull by plug rather than cord when disconnecting char
Summary of the content on the page No. 7
90550129 PC1800D 4/1/09 2:38 PM Page 7 : Burn hazard. Battery liquid may be flammable if exposed to spark or flame. • Charge the battery packs only in PORTER-CABLE chargers. • DO NOT splash or immerse in water or other liquids. This may cause premature cell failure. • Do not store or use the tool and battery pack in locations where the temperature may reach or exceed 105°F (40˚C) (such as outside sheds or metal buildings in summer). : Never attempt to open the battery pack for any reason. If
Summary of the content on the page No. 8
90550129 PC1800D 4/1/09 2:38 PM Page 8 3. The LED will flash indicating that the battery is being charged. 4. The completion of charge is indicated by the LED remaining on continuously. The pack is fully charged and may be used at this time or left on the charger. CHARGER DIAGNOSTICS This charger is designed to detect certain problems that can arise with the battery packs or the power source. Problems are indicated by one LED flashing in different patterns. BAD BATTERY The charger can detect
Summary of the content on the page No. 9
90550129 PC1800D 4/1/09 2:38 PM Page 9 : Safety Warnings and Instructions: Drills 1. Hold drill firmly with one hand on the grip and the other hand on the bottom of the battery pack. 2. When attaching accessories in the drill chuck, hand tighten the keyless chuck firmly. : Drill may stall (if overloaded or improperly used) causing a twist. Always expect the stall. Grip the drill firmly to control the twisting action and prevent loss of control which could cause personal injury. If a stall do
Summary of the content on the page No. 10
90550129 PC1800D 4/1/09 2:38 PM Page 10 LED WORK LIGHT When drill is activated by pulling the trigger switch (1), the integrated LED work light (9) will automatically illuminate the work area. ADJUSTING TORQUE CONTROL - FIGURE F This tool is fitted with a torque adjustment F collar (3) to select the operating mode and to set the torque for tightening screws. Large screws and hard workpiece materials require a higher torque setting than small screws and soft workpiece materials. 3 • For drilli
Summary of the content on the page No. 11
90550129 PC1800D 4/1/09 2:38 PM Page 11 SCREW DRIVING For driving fasteners, the reversing button should be pushed to the left. Use reverse (button pushed to the right) for removing fasteners. When moving from forward to reverse, or vice versa, always release the trigger switch first. ON BOARD BIT STORAGE A bit storage slot is built-in to the area just above the battery. DRILLING • Use sharp drill bits only. • Support and secure work properly, as instructed in the Safety Instructions. • Use
Summary of the content on the page No. 12
90550129 PC1800D 4/1/09 2:38 PM Page 12 TROUBLESHOOTING Problem Possible Cause Possible Solution • Unit will not start. • Battery pack not installed properly. • Check battery pack installation. • Battery pack not charged. • Check battery pack charging requirements. • Battery pack will not charge. • Battery pack not inserted into charger. • Insert battery pack into charger until LED appears. • Charger not plugged in. • Plug charger into a working outlet. Refer to “Important Chargin
Summary of the content on the page No. 13
90550129 PC1800D 4/1/09 2:38 PM Page 13 1 YEAR FREE SERVICE: PORTER-CABLE will maintain the tool and replace worn parts caused by normal use, for free, any time during the first year after purchase. 90 DAY MONEY BACK GUARANTEE: If you are not completely satisfied with the performance of your PORTER-CABLE Power Tool for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund – no questions asked. LATIN AMERICA: This warranty does not apply to pro
Summary of the content on the page No. 14
90550129 PC1800D 4/1/09 2:38 PM Page 14 Perceuse-visseuse sans fil de 18v et 13 mm (1/2 po) Manuel d'instructions www.portercable.com N° DE CATALOGUE PC1800D 14 8 10 12 14
Summary of the content on the page No. 15
90550129 PC1800D 4/1/09 2:38 PM Page 15 Avertissements de sécurité généraux pour les outils électriques Lire tous les avertissements de sécurité et toutes les directives. Le non-respect des avertissements et des directives pourrait se solder par un choc électrique, un incendie et/ou une blessure grave. Conserver tous les avertissements et toutes les directives pour un usage ultérieur. Le terme «outil électrique» cité dans les avertissements se rapporte à votre outil électrique à alimentatio
Summary of the content on the page No. 16
90550129 PC1800D 4/1/09 2:38 PM Page 16 d) Retirer toute clé de réglage ou clé standard avant de démarrer l’outil. Une clé standard ou une clé de réglage attachée à une partie pivotante peut causer des blessures. e) Ne pas trop tendre les bras. Conserver son équilibre en tout temps. Cela permet de mieux maîtriser l’outil électrique dans les situations imprévues. f) S’habiller de manière appropriée. Ne pas porter de vêtements amples ni de bijoux. Garder les cheveux, les vêtements et les gant
Summary of the content on the page No. 17
90550129 PC1800D 4/1/09 2:38 PM Page 17 6) Réparation a) Faire réparer l’outil électrique par un réparateur professionnel en n’utilisant que des pièces de rechange identiques. Cela permettra de maintenir une utilisation sécuritaire de l’outil électrique. CONSIGNES DE SÉCURITÉ PARTICULIÈRES • Porter des protecteurs auditifs si une perceuse à percussion est utilisée. Une exposition au bruit peut entraîner une perte auditive. • Utiliser les poignées auxiliaires fournies avec l’outil. Une perte
Summary of the content on the page No. 18
90550129 PC1800D 4/1/09 2:38 PM Page 18 LIGNES DIRECTRICES EN MATIÈRE DE SÉCURITÉ - DÉFINITIONS Il est important que vous lisiez et compreniez ce mode d’emploi. Les informations qu’il contient concernent VOTRE SÉCURITÉ et visent à ÉVITER TOUT PROBLÈME. Les symboles ci-dessous servent à vous aider à reconnaître cette information. Indique une situation dangereuse imminente qui, si elle n’est pas évitée, causera la mort ou des graves blessures. Indique une situation potentiellement dangereuse qu
Summary of the content on the page No. 19
90550129 PC1800D 4/1/09 2:38 PM Page 19 DESCRIPTION FONCTIONNELLE - FIGURE A 4 A 1. Détente 5 3 2. Bouton de marche avant/marche arrière 3. Bague de réglage de couple 2 4. Engrenage à deux vitesses 9 5. Mandrin auto-serrant 6. Porte-embout 1 7. Pile 8. Bouton de dégagement du bloc- piles 9. Lampe de travail à DEL 6 8 7 DIRECTIVES DE SÉCURITÉ IMPORTANTES POUR LES CHARGEURS DE PILES CONSERVER CES DIRECTIVES : ce mode d’emploi comprend d’importantes directives de sécurité pour les chargeurs
Summary of the content on the page No. 20
90550129 PC1800D 4/1/09 2:38 PM Page 20 provoquer une chaleur interne excessive. Éloigner le chargeur de toute source de chaleur. La ventilation du chargeur se fait par les fentes pratiquées dans les parties supérieures et inférieures du boîtier. • Ne pas installer le chargeur sur un mur ni le fixer de manière permanente sur toute surface. Le chargeur est destiné à une utilisation sur une surface plane et stable (c.-à-d. un dessus de table ou d’établi). • Ne pas faire fonctionner le chargeu
