Summary of the content on the page No. 1
BC2310DL
848J9893A1 (708)
G G
B B
OWNER’S MANUAL
BRUSHCUTTERS
BC2310DL
GB-1
Summary of the content on the page No. 2
BC2310DL EXPLANATION OF SYMBOLS AND SAFETY WARNINGS WARNING!!! RISK OF DAMAGING HEARING Wear head, eye and ear protection. MODEL SOUND LEVEL VIBRATION LEVEL EN27917 ISO 22868 : 2005 ISO 22867 : 2004 LwA idling racing LpA measured guaranteed 3 2 2 BC2310DL 22.5 cm 97.3 dB(A) 107.9 dB(A) 110 dB(A) 3.5 m/s 5.3 m/s APPROVAL NUMBER OF CE EXHAUST EMISSION REGULATION DIRECTIVE 97/68/EC AMENDED 2002/88/EC e13*97/68SH2G3*2002/88*0104*04 GB-2
Summary of the content on the page No. 3
BC2310DL G B EC DECLARATION OF COMFORMITY We, ZENOAH CO., LTD. 1-9, Minamidai, Kawagoe, Saitama, Japan declare in sole responsibility that the following products referred to in this declaration conform with DIRECTIVE 89/336/EEC, 98/37/EC, 2000/14/EC, 2002/88/EC, 2002/44/EC EN ISO 11806 : 1997 The products referred to are: DESIGNATION : BRUSHCUTTER MODELS : BC2310DL SERIAL NUMBERS : 51100101 and up The company named above will keep on file the following technic
Summary of the content on the page No. 4
BC2310DL 1. Parts location 5 (1) Primer pump 3 (2) Air cleaner cover 14 2 (3) Choke lever 1 13 (4) Fuel tank 4 (5) Starter knob 11 (6) Line head 12 (7) Gear case 9 (8) Cutting attachment guard (9) Loop handle (10) Shaft tube (11) Suspention point (12) Throttle trigger 10 (13) Stop switch (14) Throttle cable 7 8 6 2. Specification Overall size (L 3 W 3 H) ........................................................... 1765 x 330 x 310 mm Dry weight ....................................................
Summary of the content on the page No. 5
15m (50ft) BC2310DL 3. Warning labels on the machine G B (1) (2) (3) (4) (5) (6) (7) (1) Read owner’s manual before operating this machine. (2) Wear head, eye and ear protection. (3) Wear foot protection. (4) Wear gloves. (5) Beware of thrown objects. (6) Warning / Attention (7) Keep all children, bystanders and helpers 15 meters away from the machine. If warning label peels off or becomes soiled and Never modify your machine. impossible to read, you should contact the We won’t war
Summary of the content on the page No. 6
BC2310DL 5. For safe operation b. At night, at times of heavy fog, or at any other times when 1. Read this manual carefully until your field of vision might be you completely understand and limited and it would be diffi- follow all safety and operating cult to gain a clear view of the instructions. working area. 2. Keep this manual handy so that c. During rain storms, during you may refer to it later when- lightning storms, at times of ever any questions arise. Also strong or gale-force winds,
Summary of the content on the page No. 7
BC2310DL 5. For safe operation and hold it firmly in place so as to ensure that neither the cutting BEFORE STARTING part nor the throttle come into THE ENGINE contact with any obstacle when 1. The area within a perimeter of the engine starts. 15 m of the person using the product should be considered a G WARNING hazardous area into which no one B should enter. If necessary, yellow Never place the throttle into the warning rope, warning signs high-speed position when starting should be placed
Summary of the content on the page No. 8
BC2310DL 5. For safe operation could result in serious burns or elec- HANDLING FUEL trical shock. 1. The engine of the ZENOAH prod- uct is designed to run on a mixed • IF SOMEONE COMES fuel, which contains highly flam- 1. Guard against hazardous situa- mable gasoline. Never store cans tions at all times. Warn adults to of fuel or refill the tank of the unit keep pets and children away from in any place where there is a the area. Be careful if you are ap- boiler, stove, wood fire, electrical p
Summary of the content on the page No. 9
BC2310DL 6. Set up INSTALLING HANDLE • Mount the handle to the shaft tube and clamp it at a location that is comfortable to you. G B (1) (1) About 28cm (11 inches) INSTALLING CUTTING ATTACHMENT GUARD • Attach the cutting attachiment guard with the bolts provided while inserting the spacer between the guard and the pipe. • Attach the guard skirt on the guard. INSTALLING CUTTING HEAD 1. Remove the plastic tube that is attached to the gear shaft. 2. Firmly screw the line head assembly onto the gear
Summary of the content on the page No. 10
BC2310DL 7. Fuel ■ FUEL 3. Pour in all of the oil and agitate well. 4. Pour in the rest of gasoline and agitate again for at least one minute. As some oils may be difficult to agi- WARNING tate depending on oil ingredients, sufficient agitation is necessary for the engine to last long. Be careful • Gasoline is very flammable. Avoid smoking or that, if the agitation is insufficient, there is an increased bringing any flame or sparks near fuel. Make sure danger of early piston seizing due to abn
Summary of the content on the page No. 11
BC2310DL 8. Operation STARTING ENGINE WARNING WARNING The product is equipped with a centrifugal clutch mechanism, so the cutting attachment begins to ro- The cutting head will start rotating upon the engine tate as soon as the engine is started by putting the G starts. throttle into the start position. When starting the en- B gine, place the product onto the ground in a flat clear 1. Feed fuel into the fuel tank and tighten the cap se- area and hold it firmly in place so as to ensure that c
Summary of the content on the page No. 12
BC2310DL 8. Operation ADJUSTING THROTTLE CABLE TRIMMING GRASS AND WEEDS • The normal play is 1 or 2 mm when measured at the • Always remember that the TIP of the line does cut- carburetor side end. Readjust with the cable adjuster ting. You will achieve better results by not crowding as required. the line into the cutting area. Allow the unit to trim at its own pace. 1. Hold the unit so the head is off the ground and is tilted about 20 degrees toward the sweep direction. .04 in (1) (1 ~ 2 mm) (1
Summary of the content on the page No. 13
BC2310DL 9. Maintenance Every Every Every 25 50 100 Before System/components Procedure Note hours hours hours use after after after fuel leaks, fuel spillage wipe out ✔ G fuel tank, air filter, fuel filter inspect/clean ✔✔ replace, if necessary B see adjusting replace carburetor idle adjusting screw ✔ idling speed if necessary clean and readjust GAP: .025 in (0.6 ~ 0.7 mm) spark plug ✔ plug gap replace, if necessary cylinder fins, intake air cooling vent clean ✔ m
Summary of the content on the page No. 14
BC2310DL 9. Maintenance SPARK PLUG GEAR CASE • Starting failure and misfiring are often caused by a fouled spark plug. Clean the spark plug and check • The reduction gears are lubricated by multipurpose, that the plug gap is in the correct range. For a re- lithium-based grease in the gear case. Supply new placement plug, use the correct type specified by grease every 25 hours of use or more often depend- ZENOAH. ing on the job condition. • Remove the bolt opposit to the grease nipple before
Summary of the content on the page No. 15
BC2310DL 9. Maintenance PROCEDURES TO BE PERFORMED AFTER 4. Wind up the line in the correct direction as indicated EVERY 100 HOURS OF USE on the spool. G B 1. Remove the muffler, insert a screwdriver into the vent, and wipe away any carbon buildup. Wipe away any 5. Hook each end of the line in the slot on the edge of carbon buildup on the muffler exhaust vent and cylin- the spool, and then put the ends through the eyelets der exhaust port at the same time. on the housing. Make sure that the spri
Summary of the content on the page No. 16
BC2310DL 12. Troubleshooting guide Case 1. Starting failure CHECK PROBABLE CAUSES ACTION fuel tank → incorrect fuel → drain it and use correct fuel fuel filter → fuel filter is clogged → clean carburetor adjustment screw → out of normal range → adjust to normal range sparking (no spark) → spark plug is fouled/wet → clean/dry → plug gap is incorrect → correct (GAP: 0.6 ~ 0.7 mm) spark plug → disconnected → retighten Case 2. Engine starts but does not keep running/hard re-starting CHECK PROBABLE C
