Summary of the content on the page No. 1
ViewScapeToolset
User Guide
R5976476/03
01/07/2004
Summary of the content on the page No. 2
Product revision Software version: 1.1 Barc o n v E vents No o rd l aa n 5 , B -8 52 0 K uu rn e Phone: + 32 56 .36.89.70 Fax: +32 56.36.88.24 E-mail: events@ ba rc o. com Visit us at th e w eb: www.barco.com Printed in B elgium
Summary of the content on the page No. 3
Copyright © All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of Barco. Trademarks Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders. All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for th
Summary of the content on the page No. 4
Summary of the content on the page No. 5
Table o f c ontents TABLE OF CONTENTS 1. Introduction..........................................................................................5 1.1 General introduction............................................................................................ 5 2. Installation............................................................................................7 2.1 General Requirements ......................................................................................... 7 2.2 Softwa
Summary of the content on the page No. 6
Table of con tents 7.5 Making group changes to a window .........................................................................50 7.6 Z-Order .........................................................................................................50 7.7 Aspect Ratio....................................................................................................52 7.8 Changing a window name ....................................................................................52 7.9 Changing th
Summary of the content on the page No. 7
Table o f c ontents 11.2.2 Image Processing........................................................................................99 11.3 Input D320 YUV/RG(s)B ......................................................................................99 11.3.1 Settings start up..........................................................................................99 11.3.2 Image Processing...................................................................................... 100 11.3.3 Input Gain E
Summary of the content on the page No. 8
Table of con tents 4 R5976476 VIEW SCAPE TOOLSET 01/07/2004
Summary of the content on the page No. 9
1. Introduction 1. INTRODUCTION 1.1 General introduction Overview ViewScape Toolset software has a guided set up menu with clear wiring diagrams for a hardware setup. The total screen area is represented as a single canvas onto which the input sources can be arranged by a drag and drop operation. Several layouts can be stored as presets and recalled at any point during the show. Advanced effects control is built in. E.g. : •Viewport • Zoom within a View port. • Alpha blending, transforming selec
Summary of the content on the page No. 10
1. Introdu ction 6 R5976476 VIEW SCAPE TOOLSET 01/07/2004
Summary of the content on the page No. 11
2 . Installation 2. INSTALLATION Overview • General Requirements • Software installation •Startingup •Closing 2.1 General Requirements Before you begin It assumes you are familiar with the Windows operating system at your site. The CD-ROM in your package contains a Windows-based installation program. You can install the soft- ware from the CD-ROM. System requirements A minimum configuration of a Pentium II processor, 160 MHz and 128 MB of RAM. At least 50 MB of disk space. A CD-ROM drive. The op
Summary of the content on the page No. 12
2. Installation 8. For a new installation select ’Typical’. With ’Typical’, everything necessary to run the program will be installed (Tomcat webserver, Java envi- ronment variables and plug ins for the applets). With ’Custom’ you have the choice to install only the ViewScape part or only the Java part. With ’Compact’ you can install the components you want. Only recommended for advanced users. (image 2-1) 9. Press Next to execute the installation program. 10.Install java component if necessary.
Summary of the content on the page No. 13
2 . Installation Image 2-2 Internet options Settings 2.3 Starting up Start up To start up the ViewScape Toolset software, the following steps are involved: 1. Go to the Start menu, select Programs. 2. Drag your mouse to the right and select ’ViewScape Toolset’. 3. Drag to the right and launch first ’Service Launcher’. (image 2-3) The service launcher starts up the following processes: - Tomcat Webserver -Driver - Admin engine - sysid An icon will be added to the task bar. 4. Go again to Start →
Summary of the content on the page No. 14
2. Installation Image 2-5 Start up of the wizard Image 2-6 Start up when configuration known 10 R5976476 VIEW SCAPE TOOLSET 01/07/2004
Summary of the content on the page No. 15
2 . Installation 2.4 Closing How to close 1. Close the browser always as first by clicking on the browser close button (cross in the right upper corner) 2. Right click on the launcher icon and select Exit. R5976476 V IE WSCAPE TOOLSET 01 /07/2004 11
Summary of the content on the page No. 16
2. Installation 12 R5976476 VIEW SCAPE TOOLSET 01/07/2004
Summary of the content on the page No. 17
3. Configu ratio n W izard 3. CONFIGURATION WIZARD Overview • The wizard window • Set up paths • Creating a new configuration • Loading a saved configuration 3.1 The wizard window Purpose The wizard will guide you trough the configuration process of your hardware (ViewScape and projectors). The window buttons The following buttons are available in the wizard: : the wizard goes to the next window. : the wizard returns to the previous window. : the wizard gives more info about the items on the act
Summary of the content on the page No. 18
3. Configuration W iza rd 3.3 Creating a new configuration Overview • Based on ViewScape devices • Based on the output requirements (resolution) • Creating a configuration starting from last saved file • Current Configuration • Digitizer output selection • Defining the working windows • Removing windows out of the list • Configuration preview • Autodetection of connected devices • Compare Autodetected configuration – Created configuration • Updating the configuration • Output check • Mechanical
Summary of the content on the page No. 19
3. Configu ratio n W izard Image 3-1 Create new configuration Image 3-2 New configuration based on ViewScape devices 3.3.1.2 Set up What will be done During the set up, the screen configuration and resolution should be entered. At the same time a preview with the real width and height will be displayed. Device set up 1. Click on the drop down box next to Device setup.(image3-3) 2. Select the corresponding configuration. E.g. 4x1, means 4 screens next to each other making up one display. Possible
Summary of the content on the page No. 20
3. Configuration W iza rd Image 3-3 Device setup Resolution per screen The same resolution for each screen can be set up: 1. Click on the drop down box next to Resolution per screen.(image3-4) 2. Select the resolution, corresponding with the resolution of your display device. Possible resolutions : - SVGA -XGA - SXGA - SXGA+ -UXGA When changing the resolution, the real dimensions in the lower pane preview of the window will change accordingly. Image 3-4 Resolution per screen What is overlap area
