Summary of the content on the page No. 1
UltraATA 133 PCI
Quick Installation Guide
Introducing the UltraATA 133 PCI
The UltraATA 133 PCI is an ultra high-speed dual channel
Ultra ATA/133 controller board for use in Pentium-class
computer.
Features and Benefits
• Compliant with UltraDMA6 ATA/133 specifications
Compliant with PCI v2.2 Plug-n-Play
Provides two independent Ultra ATA channels
(built-in 256-byte FIFOs per channel)
Full ACPI power management support
Supports Ultra DMA 0-6 and Multi-word DMA 0-2
Breaks the 137GB barr
Summary of the content on the page No. 2
Package Contents • UltraATA 133 PCI adapter Driver diskette 40-pin/80-wire Ultra ATA cable This quick installation guide Layout Pin1 IDE2 Pin1 IDE1 HDD Activity LED Jumper On (do not remove) Figure 1. UltraATA 133 PCI RAID layout Hardware Installation General instructions for installing the card are provided below. Since the design of computer cases and motherboards vary, refer to your computer’s reference manual for further information, if needed. Static Electricity Discharge may perman
Summary of the content on the page No. 3
1. Turn OFF the power to your computer and any other connected peripheral devices. 2. Unplug the power cord from the back of the computer. 3. Remove your computer’s cover. 4. Remove the slot bracket from an available PCI slot. 5. To install the card, carefully align the card's bus connector with the selected PCI slot on the motherboard. Push the board down firmly, but gently, until it is well seated. 6. Replace the slot bracket's holding screw to secure the card. Device Connection The UltraATA 1
Summary of the content on the page No. 4
4. The Ultra ATA ribbon cable has two connectors. If you install only one drive, connect it to the end connector of the cable. On the other hand, if you install two drives, connect the master drive to the end connector of the cable and the slave drive in the middle connector. Figure 2. Connecting the cable 5. Reconnect the system power and other peripherals to your computer. Driver Installation This section provides information on how to install the UltraATA 133 PCI drivers for the following o
Summary of the content on the page No. 5
Windows 98SE For New Windows 98SE Installation 1. Install the board and follow Microsoft procedures to install Windows 98SE accordingly. 2. Once Windows has been installed, right click My Computer and click Properties. Select Device Manager tab. 3. Double click PCI Mass Storage Controller listed under Other Devices. 4. Select Driver tab, then click Update Driver button. 5. Insert the driver diskette and click Next. 6. Select Search for a better driver ... and click Next. 7. Check Floppy disk dr
Summary of the content on the page No. 6
Windows ME For New Windows ME Installation 1. Install the board and follow Microsoft procedures to install Windows ME accordingly. 2. Once Windows has been installed, right click My Computer, then click Properties. Select Device Manager tab. 3. Double click PCI Mass Storage Controller listed under Other Devices. 4. Select Driver tab, then click Update Driver button. 5. Insert the driver diskette, select Automatic search for a better driver (Recommended), then click Next. 6. Click Finish, remove
Summary of the content on the page No. 7
3. Highlight Silicon Image SiI 0680 ATA/133 Controller and click Properties. A message This device is working properly is displayed in the dialog box, the driver has been correctly installed. If any error message is displayed, remove Silicon Image SiI 0680 ATA/133 Controller and restart your system. Windows NT 4.0 For New Windows NT 4.0 Installation 1. Install the board and follow Microsoft procedures to install Windows NT 4.0 accordingly. 2. At the Windows NT Setup screen, press F6 to specify
Summary of the content on the page No. 8
To Verify Windows NT 4.0 Installation 1. Double click My Computer/Control Panel/SCSI Adapters. 2. Highlight Silicon Image SiI 0680 ATA/133 Controller from SCSI Adapters listing and click Properties. A message This device is working properly is displayed in the dialog box, the driver has been correctly installed. Windows 2000 For New Windows 2000 Installation 1. Install the board and follow Microsoft procedures to install Windows 2000 accordingly. 2. Restart your system when prompted during Windo
Summary of the content on the page No. 9
Windows XP/Server 2003 For New Windows XP/Server 2003 Installation 1. Install the board and follow Microsoft procedures to install Windows XP accordingly. 2. Restart your system when prompted during Windows' installation. 3. At the Windows Setup screen, press F6 to install the driver. 4. Insert the driver diskette. Press S then press Enter. 5. Select Silicon Image SiI 0680 ATA/133 Controller and press Enter. 6. Press Enter to continue and follow on-screen instructions to complete Windows XP inst
Summary of the content on the page No. 10
To Verify Windows 2000/XP/2003 Installation 1. Right click My Computer and click Manage. 2. Select Device Manager. 3. Double click SCSI and RAID Controllers, then double click Silicon Image SiI 0680 ATA/133 Controller to display driver properties. 4. A message This device is working properly is displayed in the dialog box, the driver has been correctly installed. Bios Configuration The UltraATA 133 PCI BIOS will appear everytime your system starts up. If the bios doesn't show, please try your c
Summary of the content on the page No. 11
Technical Support and Warranty QUESTIONS? SIIG’s Online Support has answers! Simply visit our website at www.siig.com and click on Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and one of our technical support analysts will promptly respond. A lifetime manufacturer warranty supplied with this product is offered by SIIG, Inc. Please see SIIG website for more
Summary of the content on the page No. 12
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer of I/O connectivity products, including PCI & ISA serial and parallel ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b), Networking, Sound Cards, and other accessories. SIIG is the premier one-stop source of upgrades. SIIG products offer comprehensive user manuals, many user-friendly features, and are backed by an extensive manufacturer warranty. High-quality control standards are evident by t
