Summary of the content on the page No. 1
Xtreme/104-Express
User Manual
Connect Tech Inc
42 Arrow Road
Guelph, Ontario
N1K 1S6
Tel: 519-836-1291
Toll: 800-426-8979 (North America only)
Fax: 519-836-4878
Email: sales@connecttech.com
support@connecttech.com
Web: www.connecttech.com
CTIM-00045 Revision 0.00 July 30, 2008
Summary of the content on the page No. 2
Connect Tech Xtreme/104-Express User Manual Limited Lifetime Warranty Connect Tech Inc. provides a Lifetime Warranty for all Connect Tech Inc. products. Should this product, in Connect Tech Inc.'s opinion, fail to be in good working order during the warranty period, Connect Tech Inc. will, at its option, repair or replace this product at no charge, provided that the product has not been subjected to abuse, misuse, accident, disaster or non-Connect Tech Inc. authorized modification or re
Summary of the content on the page No. 3
Connect Tech Xtreme/104-Express User Manual Table of Contents Limited Lifetime Warranty............................................................................................................................. 2 Copyright Notice ............................................................................................................................................ 2 Trademark Acknowledgment ..............................................................................................
Summary of the content on the page No. 4
Connect Tech Xtreme/104-Express User Manual List of Figures Figure 1: Xtreme/104-Express Hardware Components.................................................................................. 7 Figure 2: Jumper Block Diagrams.................................................................................................................. 9 Figure 3: Example port configuration jumper block settings ....................................................................... 10 Figure 4: RS-422/485
Summary of the content on the page No. 5
Connect Tech Xtreme/104-Express User Manual Customer Support Overview If you experience difficulties after reading the manual and/or using the product, contact the Connect Tech reseller from which you purchased the product. In most cases the reseller can help you with product installation and difficulties. In the event that the reseller is unable to resolve your problem, our highly qualified support staff can assist you. Our support section is available 24 hours a day, 7 days a week
Summary of the content on the page No. 6
Connect Tech Xtreme/104-Express User Manual Introduction Connect Tech's Xtreme/104-Express multi-port serial boards provide a fully compliant PCI/104- Express communications solution for industrial and embedded needs. Xtreme/104-Express features a built-in baud rate prescaler to allow almost any non-standard baud rate to be matched with a high level of accuracy. The onboard fail-safe 1/8th load transceivers allow up to 256 devices on a multi-drop RS-485 bus. Filtering on all ports h
Summary of the content on the page No. 7
Connect Tech Xtreme/104-Express User Manual Xtreme/104-Express Board Diagram Figure 1: Xtreme/104-Express Hardware Components Revision 0.00 7
Summary of the content on the page No. 8
Connect Tech Xtreme/104-Express User Manual Xtreme/104-Express Installation Overview Before you begin, take a moment to ensure your package includes the components that ship with your product. These components should include: One Xtreme/104-Express adapter One CD containing software and documentation DB-9 male fan-out cables (optional) If any of these components are missing, contact Connect Tech or your reseller. There are three stages to installing your Xtreme/104-Express: 1.
Summary of the content on the page No. 9
Connect Tech Xtreme/104-Express User Manual Half Duplex Mode In this mode the TxD+/- line driver is enabled only when data is transmitted and RxD+/- is disabled when data is being transmitted. This mode is typically used in either point-to-point 2- wire connections OR in multi-drop 2-wire bus connections. This mode requires software setup in Control Panel – System – Hardware – Device Manager – Ports – CTI Xtreme/104 PCI Express UART Serial Port. Multi-drop Mode In this mode the TxD+/
Summary of the content on the page No. 10
Connect Tech Xtreme/104-Express User Manual Figure 3: Example port configuration jumper block settings NOTE: The example above illustrates the following: Ports 1, 2, 3 and 4 are configured for RS-485 Half-Duplex Ports 5 and 6 are configured for RS-485 Multi-Drop Slave Ports 7 and 8 are configured for RS-232 RS-485 Selection: Install this jumper to configure a port for RS-422/485 mode. If the jumper is not installed, the port will function in RS-232 mode. All jumpers should be remove
Summary of the content on the page No. 11
Connect Tech Xtreme/104-Express User Manual Half Duplex and Multi-drop modes require you to select the appropriate mode via software, appropriate wiring and the proper jumper block settings. Please refer to the wiring recommendations (Figure 4) and the readme.txt files found in the appropriate directories on the CD. Tri-state Operation Xtreme/104-Express models offer a power-on tri-state option to ensure glitch-free network operation while the system is powering up. If enabled, the X
Summary of the content on the page No. 12
Connect Tech Xtreme/104-Express User Manual Connectors/Pinouts Table 1: I/O Signal Assignments for Xtreme/104-Express P3 contains the signals for ports 1-4, and P5 contains the signals for ports 5-8. Header Pin No. RS-232 Direction RS- Direction Port No. 422/485 1 or 5 1 DCD Input RxD+ Input 2 DSR Input CTS- Input 3 RxD Input RxD- Input 4 RTS Output RTS+ Output 5 TxD Output TxD+ Output 6 CTS Input CTS+ Input 7 DTR Output TxD- Output 8 RI Input RTS- Output 9 SG Signal Ground SR S
Summary of the content on the page No. 13
Connect Tech Xtreme/104-Express User Manual Table 2: DB-9 Male Pinouts Pin # RS-232 RS-422/485 DB-9 Signal Direction Signal Direction Xtreme/104-Express 1 DCD Input RxD+ Input Adapter 2 RxD Input RxD- Input 3 TxD Output TxD+ Output 4 DTR Output TxD- Output 5 SG Signal Ground SR Signal Reference 6 DSR Input CTS- Input 7 RTS Output RTS+ Output 8 CTS Input CTS+ Input 9 RI Input RTS- Output D DB-9 Male 1 5 6 9 Figure 4: RS-422/485 Wiring Diagram RS-422/48
Summary of the content on the page No. 14
Connect Tech Xtreme/104-Express User Manual Hardware Installation Installing the Xtreme/104-Express into your system 1. Turn off the power to your PCI/104-Express system and open any relevant enclosure to gain access to the stack (consult your system’s documentation for more information on this procedure). 2. Mount the Xtreme/104-Express into an available PCI Express slot. NOTE: Ensure that all PCI/104-Express cards are within 6 cards from the CPU and are stacked closest to the CP
Summary of the content on the page No. 15
Connect Tech Xtreme/104-Express User Manual Software/Driver Installation Windows Installation The following instructions outline how to install the Xtreme/104-Express to a computer running Windows XP. For other operating system installations, consult the readme.txt and Installation Guides available on the CD shipped with your board(s). 1. After inserting the Xtreme/104-Express into your system’s PCI Express slot, turn on your system. A Found New Hardware Wizard will appear. Insert
Summary of the content on the page No. 16
Connect Tech Xtreme/104-Express User Manual 3. Once you have clicked Next , the Found New Hardware Wizard will begin to install the software. 4. Next a window will appear indicating that the software for Xtreme/104-Express has not passed Windows logo testing. Select Continue Anyway. GPIO Adapter 16 Revi
Summary of the content on the page No. 17
Connect Tech Xtreme/104-Express User Manual 5. CTI Xtreme/104 PCI Express GPIO Adapter installation is complete. Select Finish. 6. Once the software for the CTI Xtreme/104 PCI Express GPIO Adapter has been installed, a window will appear to begin the installation for the PCI Serial Port. Select Install from a list or specific location (Advanced). Select Next. Revision 0.00 17
Summary of the content on the page No. 18
Connect Tech Xtreme/104-Express User Manual 7. Choose Select removable media (floppy, CD-ROM) and Include this location in the search and type D:\ Drivers\Win2K-XP, where D is the drive letter of your CD ROM. Now select Next. 8. Once you have clicked Next , the Found New Hardware Wizard will begin to install the software. 18 Revision 0.00
Summary of the content on the page No. 19
Connect Tech Xtreme/104-Express User Manual 9. Next a window will appear indicating that the software for Xtreme/104-Express has not passed Windows logo testing. Select Continue Anyway. 10. CTI Xtreme/104 PCI Express Multiport Serial Adapter installation is complete. Select Finish. Revision 0.00 19
Summary of the content on the page No. 20
Connect Tech Xtreme/104-Express User Manual 11. Once the software for the CTI Xtreme/104 PCI Express Multiport Serial Adapter has been installed, a window will appear to begin the installation for the Xtreme/104 PCI Express UART Serial Port. Select Install from a list or specific location (Advanced). Select Next. 12. Choose Select removable media (floppy, CD-ROM) and Include this location in the search and type D:\ Drivers\Win2K-XP, where D is the drive letter of your CD ROM. Now s
