Apple 073-0808 REV. C user manual

User manual for the device Apple 073-0808 REV. C

Device: Apple 073-0808 REV. C
Size: 0 MB
Date of adding : 2014-03-05 14:20:34
Number of pages: 7
Print the manual


How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Apple 073-0808 REV. C. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Apple 073-0808 REV. C.

For your convenience

If looking through the Apple 073-0808 REV. C user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manualApple 073-0808 REV. C on full screen, use the buttonFullscreen.
  • Downloading to your computer - You can also download the user manual Apple 073-0808 REV. C to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Apple 073-0808 REV. C user manual
« Page 1 of 7 »
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Apple 073-0808 REV. C but the selected pages only. paper.


Below you will find previews of the content of the user manuals presented on the following pages to Apple 073-0808 REV. C. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

 Power Mac G5
Replacement Instructions
Follow the instructions in this sheet carefully. Failure to follow these instructions could
damage your equipment and void its warranty.
Online instructions are available at
Note: These instructions apply to different versions of the Power Mac G5. While some
models may look slightly different from the one shown in the illustrations, the steps for all
models are the same.

Summary of the content on the page No. 2

AGP Cards The AGP video card, installed in slot 1, contains the graphics processor unit (GPU) and provides the computer’s display ports. Slot 1 is designed specifically to accept AGP cards. This 533-megahertz (MHz) slot accommodates 1.5-volt (V) AGP cards. PCI Cards The remaining three expansion slots, labeled 2, 3, and 4, accommodate PCI cards up to 12 inches long. Depending on the Power Mac G5 model, you can install either PCI or PCI-X cards. Note: To determine if your Pow

Summary of the content on the page No. 3

Opening the Computer 1. Shut down the computer. Warning: Always shut down the computer before opening it to avoid damaging its internal components or the components you are installing. Do not open the computer or attempt to install items inside it while it is on. 2. Wait 5 to 10 minutes to allow the computer’s internal components to cool. Warning: After you shut down the system, the internal components can be very hot. You must let the computer cool down before continuing. 3. Un

Summary of the content on the page No. 4

6. Hold the side access panel and lift the latch on the back of the computer. (Figure 3) Warning: The edges of the access panel and the enclosure can be sharp. Be very careful when handling them. 7. Remove the access panel and place it on a flat surface covered by a soft, clean cloth. Figure 3 Power Mac G5 AGP/PCI Card - 4

Summary of the content on the page No. 5

8. Remove the air deflector and place it on a soft, clean cloth. (Figure 4) Figure 4 Important: Always remember to replace the air deflector after you have finished working inside your computer. The Power Mac G5 computer will not function properly if the air deflector is not replaced. Removing the Installed AGP/PCI Card 1. Locate the AGP/PCI card inside the computer. (Figure 5) Figure 5 Power Mac G5 AGP/PCI Card - 5

Summary of the content on the page No. 6

2. Carefully lay the computer on its side so that the open side faces up. 3. Remove the screw that mounts the card to the enclosure. (Figure 6) Warning: When removing or installing a PCI or AGP card, handle it only by the edges. Do not touch its connectors or any of the components on the card. Lift the card straight out from the connector to remove it, and insert it straight into the connector to install it. Do not rock the card from side to side and don’t force the card into the sl

Summary of the content on the page No. 7

2. If you’re installing a 12-inch card, make sure the card engages the appropriate slot in the PCI card guide. 3. Replace the card’s mounting screw. Closing the Computer 1. Replace the air deflector by inserting the three tabs on the bottom edge of the deflector into the three slots in the bottom frame of the enclosure. Then swing the deflector up flush against the top frame. Important: Make sure you re-install the air deflector before replacing the access panel. If the air defle

Alternative user manuals
# User manual Category Download
1 Apple eMac ATI Graphics Computer Hardware 4
2 Apple FireWire Cable Computer Hardware 1
3 Apple 073-0808 REV. C Computer Hardware 1
4 Apple ATA Drive Cable Computer Hardware 1
5 Apple 073-0562 Computer Hardware 1
6 Apple EY5QGRAMKEEPER Computer Hardware 0
7 Apple ATA Controller Board Computer Hardware 0
8 Apple Drive Interconnect Board Computer Hardware 0
9 Apple Optical Drive Bracket Computer Hardware 0
10 Apple Logic Board Computer Hardware 0