Summary of the content on the page No. 1
ESM-2850
Intel Pentium® M/Celeron® M ETXexpress Module
User’s Manual
nd
2 Ed – 22 September 2006
Part No. 2047285001R
Summary of the content on the page No. 2
ESM-2850 FCC Statement THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINT
Summary of the content on the page No. 3
User’s Manual Disclaimer Evalue Technology Inc. reserves the right to make changes, without notice, to any product, including circuits and/or software described or contained in this manual in order to improve design and/or performance. Evalue Technology assumes no responsibility or liability for the use of the described product(s), conveys no license or title under any patent, copyright, or masks work rights to these products, and makes no representations or warranties that these produc
Summary of the content on the page No. 4
ESM-2850 Technical Support We want you to get the maximum performance from your products. So if you run into technical difficulties, we are here to help. For the most frequently asked questions, you can easily find answers in your product documentation. These answers are normally a lot more detailed than the ones we can give over the phone. So please consult the user’s manual first. To receive the latest version of the user’s manual; please visit our Web site at: http://www.evalue-te
Summary of the content on the page No. 5
User’s Manual Product Warranty Evalue warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Evalue, or which have been subject to misuse, abuse, accident or improper installation. Evalue assumes no liability under the terms of this warranty as a co
Summary of the content on the page No. 6
ESM-2850 Contents 1. Getting Started............................................................................................................9 1.1 Safety Precautions....................................................................................................9 1.2 Packing List...............................................................................................................9 1.3 Document Amendment History ...............................................................
Summary of the content on the page No. 7
User’s Manual 3.5.11 Save & Exit Setup ...................................................................................................................... 65 3.5.12 Exit Without Save....................................................................................................................... 66 4 Drivers Installation ...................................................................................................67 4.1 Install Chipset Driver (For Intel NQ82915GM) ............
Summary of the content on the page No. 8
ESM-2850 27. Wrong Board In Slot PLEASE RUN EISA CONFIGURATION UTILITY........................................ 81 28. FLOPPY DISK(S) fail (80) → Unable to reset floppy subsystem................................................... 81 29. FLOPPY DISK(S) fail (40) → Floppy Type dismatch..................................................................... 81 30. Hard Disk(s) fail (80) → HDD reset failed.................................................................................... 81 31.
Summary of the content on the page No. 9
User’s Manual 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the CPU card. Modern electronic
Summary of the content on the page No. 10
ESM-2850 1.3 Document Amendment History Revision Date By Comment st 1 Feb. 2006 Vicky Lin Initial Release nd 2 Sep. 2006 Vicky Lin 1) 2.4.2 Signals of CN1A modified 2) 2.4.3 Signals of CN1B modified 10 ESM-2850 User’s Manual
Summary of the content on the page No. 11
User’s Manual 1.4 Manual Objectives This manual describes in detail the Evalue Technology ESM-2850 series Single Board. We have tried to include as much information as possible but we have not duplicated information that is provided in the standard IBM Technical References, unless it proved to be necessary to aid in the understanding of this board. We strongly recommend that you study this manual carefully before attempting to interface with ESM-2850 series or change the standard c
Summary of the content on the page No. 12
ESM-2850 1.5 System Specifications System Supports 90nm Intel® µFC-PGA 478 / µFC-BGA 479 Pentium® M / CPU Celeron® M CPU Note: Available in different CPU speeds by request BIOS Award 512 KB Flash BIOS System Chipset Intel® NQ82915GM GMCH/FW82801FBM ICH6-M One 200-pin DDR2 SODIMM socket supports up to 1 GB DDR2 533 System Memory SDRAM Watchdog Timer Reset: 1 sec.~255 min. and 1 sec. or 1 min./step (from the base board) Four PCI slots (PCI Rev. 2.3 compliant), three PCI Expres
Summary of the content on the page No. 13
User’s Manual 1.6 Architecture Overview 1.6.1 Block Diagram The following block diagram shows the architecture and main components of ESM-2850 series. The following sections provide detail information about the functions provided onboard. ESM-2850 User’s Manual 13
Summary of the content on the page No. 14
ESM-2850 1.6.2 Intel NQ82915GM and FW82801FMB ICH6-M The Mobile Intel® 915GM Express Chipset for Embedded Computing, consisting of the Intel® 915GM Graphic Memory Controller Hub (GMCH) and Intel® I/O Controller Hub 6-M (ICH6-M), is an optimized integrated graphics solution with a 400 MHz and 533 MHz front-side bus. The integrated 32-bit 3D graphics engine, based on Intel® Graphics Media Accelerator 900 (Intel® GMA 900) architecture, operates at core speeds of up to 320 MHz. It features
Summary of the content on the page No. 15
User’s Manual The GMCH contains one 16-lane (x16) PCI Express port intended for an external PCI Express Based graphics card. The PCI Express port is fully compliant to the PCI Express Base Specification revision 1.0a. The x16 port operates at a data rate of 2.5 GB/s while employing 8b/10b encoding. This allows a maximum theoretical bandwidth of 40 GB/s each direction. Intel 915GM/ PM may also be configured as PCI Express x1 port. The GMCH is capable of driving a CRT, LCD panel, Analog TV
Summary of the content on the page No. 16
ESM-2850 1.6.3 Ethernet 1.6.3.1 Marvell 88EE8053 Gigabit Ethernet Controller The single-chip PCI Express based 88E8053 device is ideally suited for LAN on motherboard (LOM) and Network Interface Card (NIC) applications. The 88E8053 device is compliant with the PCI Express 1.0a specification. Offered in a 9 x 9 mm, 64-pin QFN package, the 88E8053 reduces board space required for Gigabit LOM implementation significantly. • PCI Express Features: PCI Express base specification 1.0a compl
Summary of the content on the page No. 17
User’s Manual 2. Hardware Configuration ESM-2850 User’s Manual 17
Summary of the content on the page No. 18
ESM-2850 2.1 Product Overview 18 ESM-2850 User’s Manual
Summary of the content on the page No. 19
User’s Manual 2.2 Installation Procedure This chapter explains you the instructions of how to setup your system. 1. Turn off the power supply. 2. Insert the DIMM module (be careful with the orientation). 3. Insert all external cables for hard disk, floppy, keyboard, mouse, USB etc. except for flat panel. A CRT monitor must be connected in order to change CMOS settings to support flat panel. 4. Connect power supply to the board via the ATXPWR. 5. Turn on the power. 6. Enter the BIOS s
Summary of the content on the page No. 20
ESM-2850 2.2.1.2 Removing CPU • Unlock the Pentium M processor. • Carefully lift up the existing CPU to remove it from the socket. • Follow the steps of installing a CPU to change to another one. 2.2.2 Main Memory ESM-2850 series provide two 200-pin SODIMM sockets to support DDR2 533 SDRAM. The total maximum memory size is 1 GB. DIMM1 Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to bo
