Bard HAC301-AD040 user manual

User manual for the device Bard HAC301-AD040

Device: Bard HAC301-AD040
Category: Air Conditioner
Manufacturer: Bard
Size: 0.4 MB
Added : 5/22/2014
Number of pages: 25
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Bard HAC301-AD040. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Bard HAC301-AD040.

For your convenience

If looking through the Bard HAC301-AD040 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Bard HAC301-AD040 on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Bard HAC301-AD040 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Bard HAC301-AD040 User manual - Online PDF
Advertisement
« Page 1 of 25 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Bard HAC301-AD040 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Bard HAC301-AD040. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

INSTALLATION INSTRUCTIONS
SPLIT AIR CONDITIONER
OUTDOOR SECTION
Models: HAC181-AD040
HAC241-AD040
HAC301-AD040
HAC361-AD040
HAC421-AD040
HAC481-AD040
HAC481-BD040
HAC601-AD040
HAC601-BD040
FOR USE WITH:
MATCHING INDOOR
BLOWER COIL UNITS
AND MATCHING ADD
ON COIL UNITS ONLY
Manual No.: 2100-346C
Bard Manufacturing Company
Supersedes: 2100-346B
Bryan, Ohio 43506
File: Volume 1, Tab 4
Since 1914 . . . Moving ahead just as planned.
Date: 09-04-02
© Copyright 2002

Summary of the content on the page No. 2

CONTENTS Split Air Conditioner General Information.........1 Wiring Instructions ..............................................9 Split Air Conditioner Model Nomenclature ............... 1 General .................................................................... 9 Control Circuit Wiring ............................................... 9 Application and Location ....................................4 Wall Thermostats ..................................................... 9 General ................

Summary of the content on the page No. 3

SPLIT AIR CONDITIONER MODEL NOMENCLATURE HAC 36 1 – A DXXX Customized Unit Code Electrical Characteristics A – 230/208-60-1 B – 230/208-60-3 Modification Code Capacity – 3 Ton or approx. 36,000 BTU Basic Model Number FIGURE 1 UNIT DIMENSIONAL DRAWING W ALTERNATE ELECTRICAL ENTRANCES ON BACK H HIGH VOLTAGE ENTRANCE LOW VOLTAGE ENTRANCE C REFRIGERANT SHUTOFF VALVES B F D A E MIS-1789 TABLE 1 UNIT DIMENSIONS "W" "D" "H" ModelNo. Width DepthHA eight B C E F HAC181 40

Summary of the content on the page No. 4

TABLE 2 RATED CFM AND AIR FLOW DATA (WET COIL – COOLING) Rated Airflow Condensing Evaporator Motor System Pressure Rated Recommended Unit Coil CFM Speed Orifice Drop H O E.S.P. Air Flow Range 2 Model No. Model No. Tap Required A30AS-A 650 .15 550 - 715 .052 * HAC181-A S24AS-A 650 .24 550 - 715 .052 * BC24B 650 .d 35 Me 550 - 715 .052 * A30AS-A 800 .18 700 - 910 .055 * HAC241A S24AS-A 780 .30 680 - 890 .055 BC24B 750 .h 20 Hig 700 - 910 .055 * A36AS-A 1,000 .20 850 - 1,175 .063 * HAC301-A BC36B 1

Summary of the content on the page No. 5

Manual 2100-346 Page 3 TABLE 3 SPECIFICATIONS MA ODELS HA AC181-HA AC241-HA AC301-HA AC361-HA AC421-HB AC481-HA AC481-HB AC601- HAC601- E1 lectricalRating (60HZ/V/PH) 21 30/208-21 30/208-21 30/208-21 30/208-21 30/208-23 30/208-21 30/208-23 30/208- 230/208- O3 perating Voltage Range 13 97 - 2513 97 - 2513 97 - 2513 97 - 2513 97 - 2513 97 - 2513 87 - 2513 97 - 25 187 - 25 M5 inimum CircuitAmpacity 1519102526271531 2 ¬F4 ield Wire Size 14121210101218 10 ! D0 elayFuse Maximum or CircuitBreake

Summary of the content on the page No. 6

APPLICATION and LOCATION LOCATION GENERAL The condensing unit is designed to be located outside with These instructions explain the recommended method to free and unobstructed condenser air inlet and discharge. It install the air cooled remote type condensing unit, the must also permit access for service and installation. interconnecting refrigerant tubing and the electrical wiring Condenser air enters the coil from the rear of the unit as connections to the unit. shown in Figure 2 with electri

Summary of the content on the page No. 7

NOTE: Do not braze line to units! If orifice needs to be FIGURE 3 changed, change out orifice first. INSTALLING REFRIGERANT TUBING If the orifice does not have to be changed, skip the instructions outlined further in Step 3 and proceed to Step 8. 3. Disassemble Flow Control Assembly by turning body hex. 4. If existing orifice has not dropped out of the body when disassembled, remove by using a pin or paper clip. Discard this original orifice. 5. Insert proper sized orifice fully into the flow

Summary of the content on the page No. 8

FIELD FABRICATED TUBING CONNECTIONS: A copper-silver alloy with a high silver content should QUICK CONNECT INDOOR UNIT and SWEAT be used when iron or steel material is involved in the OUTDOOR UNIT USING CTO KIT joint. These alloys require the use of silver solder flux. Alloys containing phosphorus should not be used with Use only refrigeration grade (dehydrated and sealed) copper iron or steel. Phosphorus reacts with the iron forming tubing. Care must be taken to insure that the tubing is kep

Summary of the content on the page No. 9

2. The tubing ends should be cut square. Make sure it is 8. Recover charge from the indoor unit. round and free of burrs at the connecting ends. Clean A. Connect the suction line only to the indoor unit as the tubing to prevent contaminants from entering the outlined in Steps 15, 16, and 17. system. B. Recover indoor unit and suction line unit charge NOTE: Do not make any tubing connection at indoor unit through service port located on outdoor unit base at this time. Make all brazing of joint

Summary of the content on the page No. 10

16. Lubricate male half diaphragm and synthetic rubber TABLE 5 seal with refrigerant oil. Thread coupling halves COUPLINGS together by hand to insure proper mating of threads. Be Cs oupling Size Feet Pound sure to hold the coupling firmly to prevent movement of the coupling and tubing. Failure to do so could tear out -2 6 10 - 1 the diaphragm causing a blockage of the system. Use -5 10 35 - 4 proper size wrenches (on coupling body hex and on union nut) and tighten until coupling bodies ”bott

Summary of the content on the page No. 11

WIRING INSTRUCTIONS Example: 1. Control circuit transformer rated at 40 VA GENERAL 2. Maximum total distance of control circuit All wiring must be installed in accordance with the National wiring 85 feet. Electrical Code and local codes. In Canada, all wiring must From Table 6, minimum of 18 gauge wire should be used in be installed in accordance with the Canadian Electrical the control circuit wiring. Code and in accordance with the regulations of the authorities having jurisdiction. Power su

Summary of the content on the page No. 12

Manual 2100-346 Page 10

Summary of the content on the page No. 13

Manual 2100-346 Page 11

Summary of the content on the page No. 14

OPTIONAL CONTROLS INSTALLATION INSTRUCTIONS — CMA-6 FIGURE 5 Disconnect all power to unit. Remove control panel inner and outer cover. COMPONENT MOUNTING LOCATION 1. Mount terminal block in position shown in Figure 5. CMA-5 & CMA-13A LOW AMBIENT FAN CYCLING CMA-5 COMPRESSOR 2. Disconnect black high voltage outdoor motor lead from CONTROL TERMINAL BLOCK TIME DELAY RELAY compressor contactor and reconnect to terminal block. 3. Route low ambient control wires up through the bushing in the bottom

Summary of the content on the page No. 15

7.Remove service port caps on both the suction and INSTALLATION INSTRUCTIONS – CMA-10A discharge lines. Install the high pressure switch on the Disconnect all power to unit. Remove control panel cover. discharge line to the flare tee adapter that is brazed to the controls. Install the low pressure switch on the 1. Screw compressor control module and terminal block suction line. Check for pressure at the flare tee dill into control panel as shown in Figure 5. valves after installation to insu

Summary of the content on the page No. 16

the high voltage outdoor motor lead was removed in INSTALLATION INSTRUCTIONS – CMA-13A Step 7. Disconnect all power to unit. Remove control panel cover. 9. Remove service port caps on both the suction and 1. Screw compressor control module and terminal block discharge lines. Install the high pressure switch and into control panel as shown in Figure 5. the low ambient control on the discharge line with the flare tee adapter that is brazed to the controls. Install 2. Disconnect yellow low volta

Summary of the content on the page No. 17

CHARGING INSTRUCTIONS TABLE 9 PRESSURE SERVICE PORTS SYSTEM SUPERHEAT High and low pressure service ports are installed on all units Return Air Temperature Outdoor Ambient so that the system operating pressures can be observed. F Wet Bulb Temperature ( F Pressure tables can be found later in the manual covering all Dry Bulb) models. It is imperative to match the correct pressure table 53 9 6761 7 to the unit by model number. 105 1 1 5 95 1 3 (8) 20 SYSTEM START-UP (INDOOR UNITS 90 1 7 14 26 WIT

Summary of the content on the page No. 18

TABLE 11 SCHEDULE FOR TABLE 11 TOTAL SYSTEM OPERATING CHARGE L. iquid Line Diameter Oz. R-22 Per Ft (Includes charge for the basic outdoor unit, indoor coil and 25’ of interconnecting tubing.) 1/4" 0.25 3/8" 0.60 1/2" 1.20 Total R-22 Installer Note: Stamp or mark the final system charge On utdoor Section Indoor Sectio Charge (Oz.) determined above on the outdoor unit serial plate. A30AS-A 73 oz. HAC181-A S24AS-A 73 oz.  BC24B 78 oz. A30AS-A 80 oz. HAC241-A S24AS-A 80 oz.  BC24B 79 oz. A36AS-

Summary of the content on the page No. 19

SERVICE FIGURE 10 SERVICE HINTS FAN BLADE 1. Caution homeowner to maintain clean air filters at all times. Also, not to needlessly close off supply and return air registers. This reduces air flow through the system, which shortens equipment service life, as well C as, increasing operating costs. 2. Check all power fuses or circuit breakers to be sure that they are the correct rating. 3. Periodic cleaning of the outdoor coil to permit full and unrestricted air flow circulation is essential. F

Summary of the content on the page No. 20

Manual 2100-346 Page 18


Alternative user manuals
# User manual Category Download
1 Bard Mfg. Co.P1136A1 User manual Air Conditioner 24
2 Bard Mfg. Co.W17A User manual Air Conditioner 5
3 Bard Mfg. Co.HA4S3KA User manual Air Conditioner 3
4 Bard Mfg. Co.HL5S2KA User manual Air Conditioner 4
5 Bard 357-93-E User manual Air Conditioner 4
6 Bard Mfg. Co.W12A1 User manual Air Conditioner 2
7 Bard Mfg. Co.w17a2 User manual Air Conditioner 14
8 Bard Mfg. Co.P1130A1 User manual Air Conditioner 0
9 Bard Mfg. Co.HL4S2KA User manual Air Conditioner 1
10 Bard Mfg. Co.W18L1 User manual Air Conditioner 0
11 Bard Mfg. Co.W30L1 User manual Air Conditioner 1
12 Bard Mfg. Co.W42A1 User manual Air Conditioner 4
13 Bard Mfg. Co.W24L1 User manual Air Conditioner 1
14 Bard Mfg. Co.W24A1 User manual Air Conditioner 3
15 Bard Mfg. Co.W42L2 User manual Air Conditioner 0
16 Sony SU-PW2 User manual Air Conditioner 12
17 Sony CV-P12PX User manual Air Conditioner 3
18 Sony MULTI CHANNEL AV RECEIVER STR-DG710 User manual Air Conditioner 31
19 Sony VGN-BX500 User manual Air Conditioner 1
20 Philips 190S5 User manual Air Conditioner 21