Summary of the content on the page No. 1
Summary of the content on the page No. 2
TABLE OF CONTENTS FOR YOUR SAFETY --------------------------------------------------1 SAFETY PRECAUTIONS -------------------------------------- 2 SPECIAL NOTES ON LCD MONITORS ------------------- 3 BEFORE YOU OPERATE THE MONITOR --------------------- 3 FEATURES -------------------------------------------------------- 3 PACKING LIST --------------------------------------------------- 3 INSTALLATION INSTRUCTIONS ---------------------------4 CONTROLS AND CONNECTORS -------------------------- 5 ADJU
Summary of the content on the page No. 3
Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
Summary of the content on the page No. 4
ELECTRONIC INDUSTRIES ALLIANCE AT WWW.EIAE.ORG. 3
Summary of the content on the page No. 5
PRECAUTIONS Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit inst
Summary of the content on the page No. 6
SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. NOTES Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. You may find slightly uneven brightness on the screen depending on the desktop pattern you use. The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or less su
Summary of the content on the page No. 7
INSTALLATION INSTRUCTIONS SWIVEL BASE Install Remove Figure 1 Installing and Removing the Swivel Base POWER CORD Power Source: 1. Make sure that the power cord is the correct type required in your area. 2. This LCD monitor has an External universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required.) 3. Connect the AC-power cord into your LCD monitor’s External Adapter input socket, and then plug
Summary of the content on the page No. 8
CONTROLS AND CONNECTORS Connecting Cables Turn off your computer before performing the procedure below. 1. Connect the power adapter dc cable to the DC-In port on the back of the monitor. 2. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer’s D-Sub port. 3. Plug the power cable of your monitor into a nearby outlet. Plug the other end of the power cord into the power adapter. 4. (Optional – Requires a video card with DVI port) - C
Summary of the content on the page No. 9
ADJUSTING THE VIEWING ANGLE For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. Hold the stand so you do not topple the monitor when you change the monitor’s angle. You are able to adjust the monitor’s angle from -5 to 20 . Figure 3 NOTES Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. Careful attention is required not to catch your fingers or han
Summary of the content on the page No. 10
OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. The power cord should be connected. Connect the video cable from the monitor to the video card. Press the power button to turn on the monitor position. The power indicator will light up. Figure 4
Summary of the content on the page No. 11
FRONT PANEL CONTROL Power Button: Press this button to switch ON/OFF of monitor’s power. MENU / ENTER : Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit OSD menu when in Brightness/ Contrast Adjust OSD status. Luminance : Adjust contrast and brightness or function adjust. *Only adjustable at “STD” mode (see Brightness Preset below) Brightness Preset: Switch between “STD”, “OFFICE” & “VIVID”. Auto Adjust button / Exit: 1. When OSD men
Summary of the content on the page No. 12
HOW TO ADJUST A SETTING 1. Press the MENU-button to activate the OSD window. 2. Press or to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it. If the function selected has a sub-menu, press or again to navigate through the sub-menu functions. Once the desired function is highlighted, press MENU-button to activate it. 3. Press or to change the settings of the selected function. 4. To exit and save, select the exit function. If
Summary of the content on the page No. 13
ADJUSTING THE PICTURE The descriptions for function control LEDS Main Main Sub Sub Menu Menu Menu Menu Description Item Item Icon Icon Contrast Contrast from Digital-register. Luminance Brightness Backlight Adjustment Adjust Picture Phase to reduce Focus Horizontal-Line noise Image Setup Adjust picture Clock to reduce Clock Vertical-Line noise. Adjust the horizontal position of the H. Position picture. Image Position Adjust the verticalposition of the V. Position picture. Recall Warm C
Summary of the content on the page No. 14
Main Sub Main Sub Menu Menu Menu Description Menu Item Item Icon Icon Adjust the horizontal position of H. Position the OSD. OSD Setup Adjust the verticalposition of the V. Position OSD. OSD Adjust the OSD timeout. Timeout Language Language N/A Select the language you like. Show the resolution, H/V Information Information N/A frequency and input port of current input timing. Clear each old status of Auto- Yes N/A configuration . Reset Do not execute reset, return to No N/A main menu. Exi
Summary of the content on the page No. 15
PLUG AND PLAY Plug & Play DDC 2B Feature This monitor is equipped with VESA DDC 2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC 2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC 2B channel. THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS
Summary of the content on the page No. 16
TECHNICAL SUPPORT (FAQ) Problem & Question Possible Solution Power LED is not on *Check if the Power Switch is in the ON position *Power Cord should be connected No Plug & Play *Check if the PC system is Plug & Play compatible *Check if the Video Card is Plug & Play compatible *Check if the D-15 plug pin of Video Cable is bent Picture is fuzzy *Adjust the Contrast and Brightness Controls. Picture bounces or a wave *Move electrical devices that may cause pattern is present in the picture
Summary of the content on the page No. 17
ERROR MESSAGE & POSSIBLE SOLUTION CABLE NOT CONNECTED : 1. Check that the signal-cable is properly connected , If the connector is loose, tighten the connector’s screws. 2. Check the signal-cable’s connection pins for damage. INPUT NOT SUPPORT : Your computer has been set to unsuitable display mode ,set the computer to display mode given in the following table.(see page 17) 16
Summary of the content on the page No. 18
APPENDIX SPECIFICATIONS Driving system TFT Color LCD LCD Panel Size 48cm(19") Pixel pitch 0.285mm( H ) × 0.285mm( V ) Video R,G,B Analog Interface Digital Interface Input Separate Sync. H/V TTL H-Frequency 30kHz –83kHz V-Frequency 55-75Hz Display Colors 16.2M Colors Dot Clock 135MHz Max. Resolution 1440 × 900 @60Hz TM Plug & Play VESA DDC 2B ® EPA ENERGY STAR ON Mode ≤36W OFF Mode ≤1W Input Connector 15-pin D-Sub DVI 24pin Input Video Signal Analog:0.7Vp-p(standard), 75 OHM, Positive Digital
Summary of the content on the page No. 19
Switch Auto Adjust Key Brightness Preset Luminance Power Button MENU External Controls: Functions Contrast Brightness Focus Clock H. Position V. Position (Warm)Color (Cool)Color sRGB RGB Color temperature Input select OSD Setup Language Information Reset Exit Power Consumption ( Maximum ) 36 Watts Regulatory Compliance cULus, FCC, CE, TUV/S 18
Summary of the content on the page No. 20
Preset Display Modes HORIZONTAL VERTICAL STANDARD RESOLUTION FREQUENCY FREQUENCY Dos-mode 720 × 400 31.47kHz 70.0Hz 640 × 480 31.47kHz 60.0Hz VGA 640 × 480 37.50kHz 75.0Hz 800 × 600 37.879kHz 60.0Hz SVGA 800 × 600 46.875kHz 75.0Hz 1024 × 768 48.363kHz 60.0Hz XGA 1024 × 768 56.476kHz 70.0Hz 1024 × 768 60.021kHz 75.0Hz 1280 × 1024 64.000kHz 60.0Hz SXGA 1280 × 1024 80.000kHz 75.0Hz WXGA+ 1440 × 900 55.935kHz 59.8Hz 19
