Summary of the content on the page No. 1
MULTI-PURPOSE LCD DISPLAY
MU-155C
Summary of the content on the page No. 2
The paper used in this manual is elemental chlorine free. FURUNO Authorized FURUNO Authorized Distributor/Dealer Distributor/Dealer 9-52 Ashihara-cho, 9-52 Ashihara-cho, Nishinomi Nishinomiy ya 662-8580, JAPAN a 662-8580, JAPAN Te Telle ep phone : hone : 0798-65-2111 0798-65-2111 Fa Fax x 0798-65-4200 0798-65-4200 :: FIRST EDITION : FIRST EDITION : JUN. JUN. 2004 2004 Printed in Japan Printed in Japan A All r ll riig ghts reserved. hts reserved. A3 A3 :: OCT. OCT. 24, 2006 24, 2006 Pub. No.
Summary of the content on the page No. 3
SAFETY INSTRUCTIONS Safety Instructions for the Operator Safety Instructions for the Installer WARNING WARNING Do not open the equipment. Do not open the cover unless totally familiar with Only qualified personnel electrical circuits and should work inside service manual. the equipment.
Summary of the content on the page No. 4
TABLE OF CONTENTS FOREWORD ........................................................................................................ iii SYSTEM CONFIGURATION................................................................................ iv EQUIPMENT LISTS .............................................................................................. v 1. MOUNTING ....................................................................................................... 1 1.1 Display Unit......
Summary of the content on the page No. 5
FOREWORD A Word to the Owner of the MU-155C FURUNO Electric Company thanks you for purchasing the MU-155C 15” Multi-Purpose LCD Display. We are confident you will discover why the FURUNO name has become synonymous with quality and reliability. For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for quality and reliability throughout the world. This dedication to excellence is furthered by our extensive global network of agents and dealers. Your equipment is
Summary of the content on the page No. 6
SYSTEM CONFIGURATION RGB Radar, Video Plotter, Navigator, Video Sounder, Scanning Sonar, etc. 12-24 VDC DVI FAR-2107 series etc. VIDEO (NTSC/PAL) CCD camera, Video recorder, etc. Connectable equipment Equipment Resolution Signal FR-1500 MK3 series XGA Analog FCV-1200L/1200LM* VGA Analog, via IF8000 GD/GP-280/380/680 VGA Analog CH-250 VGA Analog, via IF8000 CH-270 VGA Analog, via IF8000 CSH-5L/8L XGA Analog FSV-24/24S/30/30S SXGA Analog FR-21X5 series SXGA Analog FAR-21X7 series
Summary of the content on the page No. 7
EQUIPMENT LISTS Standard supply Name Type Code No. Qty Remarks Display Unit MU-155C − 1 w/hard cover Remote Controller RMC-200 000-012-629 1 Spare Parts* SP19-00201 001-410-490 1 set Installation Materials* CP19-00200 000-012-641 1 set Accessories* 1 set FP19-00801 001-410-510 Option Name Type Code No. Qty Remarks Hanger FP19-00900 001-410-540 1 w/knob, self-tapping screws 1 Cable length: 5 m 000-146-500 3COX-2P-6C Cable Assy 000-146-501 1 Cable length: 10 m DVI-D/D SINGLELI
Summary of the content on the page No. 8
1. MOUNTING Refer to the outline drawing at the end of this manual for mounting dimensions. Note: A grass plate covers the LCD. For this reason, handle the unit carefully. 1.1 Display Unit The display unit may be mounted on a desktop (optional hanger required) or flush mounted in a panel. When selecting a mounting location, keep in mind the following points: • Locate the unit out of direct sunlight. • Select a location where the display can be easily viewed and the controls can
Summary of the content on the page No. 9
Flush mounting See the outline drawing at the end of this manual for mounting dimensions. CAUTION Hold the hard cover and display unit together when lifting the display unit. The display unit may fall out if only the hard cover is held. 1. Remove the hard cover from the unit. 2. Using the paper template supplied in the installation materials, make a cutout in the mounting location. 3. Set the display unit to the cutout, and fasten it with four self-tapping screws (5X40, supplied as a
Summary of the content on the page No. 10
Desktop mounting The display unit can be mounted on a desktop, using the optional hanger, Type: FP19-00900, Code No.: 001-410-540. Contents of hanger mounting kit Name Type Code No. Qty Hanger FP19-00901 001-410-550 1 Knob bolt FP03-09204 008-523-650 2 Self-tapping screw 5x20 000-802-081 4 1. Fasten the hanger to the mounting location with four self-tapping screws (supplied). Note: Do not mount the unit where the exhaust or intake vent may be obstructed. Intake vent Exhaust
Summary of the content on the page No. 11
1.2 Remote Controller Write the device name (ex. “FCV-1200L”) for each “signal” key on the sticker supplied with the remote controller. Attach the sticker to the remote controller, at the location shown below. RGB1 RGB2 DVI VIDEO2 VIDEO3 VIDEO1 PIP1 PIP2 PIP3 + BRILL MENU RGB 1 : RGB2 : DVI : VIDEO1 : VIDEO2 : VIDEO3 : Sticker Remote controller RMC-200 WARNING Ensure battery polarity is correct. Wrong polarity may cause the batteries to explode. 4
Summary of the content on the page No. 12
2. WIRING Connect external equipment to the MU-155C by referring to the drawings below, the table on the next page and the interconnection diagram at the back of this manual. 12-24VDC 12-24 VDC MJ-A3SPF0017-050Z (Supplied) VIDEO3 Ground terminal VIDEO2 DVI-D VIDEO1 FAR-21X7 series CCD camera, FEA-2107 Video recorder, etc. DVI-D/D SINGLELINK5M 2.5C2V or 3C2V (Option) (Local supply) FCV-1200L/1200LM CH-250 RGB2 CH-270 CSH-5L/8L RGB1 FSV-24/24S/30/30S 3COX-2P-6C (Option) GD/GP-280/380/680 FR
Summary of the content on the page No. 13
Port, cable and connectable equipment Used cable Port Connectable Equipment Standard/ Name Name Type Code No. Option 12-24 Power MJ-A3SPF0017- 000-138-928Standard Power source VDC cable 050Z DVI DVI-D/D PC, FAR-21X7 series, DVI-D 000-149-054 Option Cable SINGLELINK5M FEA-2107 FCV-1200L/1200LM, CH-250, CH-270, 3COX-2P-6C RGB1 000-146-500 Option CSH-5L/8L, 5M Analog FSV-24/24S/30/30S, RGB GD/GP-280/380/680, Cable FR-1500 MK3 series, 3COX-2P-6C FR-21X5 series, RGB2 000-146-
Summary of the content on the page No. 14
3. ADJUSTMENTS Adjust the MU-155C according to the equipment connected. Note that you can adjust the display currently selected, at the DISP selection window. (See section 4.3.) Note: The example screens shown in this manual may not match the screens you see on your display. The screen you see depends on your system configuration and equipment settings. 3.1 RGB/DVI Setting RGB1 and RGB2 screens can be adjusted independently. Also, DVI screen can be adjusted similarly. 1. Press
Summary of the content on the page No. 15
Menu item Function Setting range H_SIZE*** Adjusts the image size horizontally. Variable depending on signal type V_SIZE*** Adjusts the image size vertically. PHASE Adjusts the characters and graphic lines. 1-32 CONTRAST Increases or decrease contrast level. 1-64 H_POSITION Moves the image position horizontally. 1-50 (DVI), 1-99 (RGB1, 2) V_POSITION Moves the image position vertically. 1-40 R_LEVEL Adjusts red color level. 1-64 G_LEVEL Adjusts green color level. 1-64 B_LEVEL Adjusts
Summary of the content on the page No. 16
3.2 VIDEO Setting VIDEO1, VIDEO2 and VIDEO3 screens; that is, the picture-in-picture windows can be adjusted as below. Picture-in-picture window Picture-in-picture window 1. Press the [MENU] key to show the main menu. 2. Press [◄] or [►] to select VIDEO1, VIDEO2 or VIDEO3 as appropriate. RGB1 RGB2 DVI VIDEO1 VIDEO2 VIDEO3 OSD SYSTEM PIP_SIZE 5 (1 – 10) CONTRAST 44 (1 – 64) R_LEVEL 31 (1 – 64) G_LEVEL 31 (1 – 64) B_LEVEL 31 (1 – 64) TEMPERATURE 70
Summary of the content on the page No. 17
3.3 Menu Window Setting 3.3.1 Adjusting the menu window The menu window can be moved and translucentized on the OSD (On Screen Display) menu. 1. Press the [MENU] key to show the main menu. 2. Press the [◄] or [►] key to select OSD. RGB1 RGB2 DVI VIDEO1 VIDEO2 VIDEO3 OSD SYSTEM H_POSITION 15 (1 – 29) V_POSITION 37 (1 – 37) TRANSLUCENT OFF (OFF/ON) CUSTOM NAME RGB1 = RGB1______ RGB2 = RGB2______ DVI = DVI_______ VIDEO1 = VIDEO1____ VIDEO2 = VIDEO2__
Summary of the content on the page No. 18
3.3.2 Changing the signal name You can change the signal name which is shown on the DISP or PIP window, described in the next chapter. It is useful to use the name of the device connected (ex. FCV-1200L). For detailed information about these windows, see Chapter 4. 1. Press the [MENU] key to show the main menu. 2. Press the [◄] or [►] key to select OSD. CUSTOM RGB1 RGB2 DVI VIDEO1 VIDEO2 VIDEO3 OSD SYSTEM NAME area H_POSITION 15 (1 – 29) V_POSITION 37 (1 – 3
Summary of the content on the page No. 19
3.4 Remote Controller Setting A remote controller can be set to be operative with a specific display unit, in the case of multiple MU-155C display units. Set the remote controller mode desired on the SYSTEM menu as follows; 1. Press the [MENU] key to show the main menu. 2. Press the [►] key to select SYSTEM. Remote controller ID square Display unit ID RGB1 RGB2 DVI VIDEO1 VIDEO2 VIDEO3 OSD SYSTEM INFRARED REMOTE A DEFAULT RESET NO INFORMATI
Summary of the content on the page No. 20
4. OPERATION 4.1 Controls Display unit DISP key Shows the DISPLAY selection window. MENU key Shows the main menu. Power key LED Optical sensor PIP key Arrow keys Shows the PIP selection window. Selects menu item. BRILL key Shows the BRILL adjustment window. Display unit Power key: Press the power key ( ) to turn the power on or off. LED: The LED changes color according to signal status as below. Green: The selected signal to be displayed is input correctly from the external device.
