Summary of the content on the page No. 1
HP 24wd LED Backlit Monitor
User Guide
Summary of the content on the page No. 2
© 2012 Hewlett-Packard Development Company, L.P. Microsoft, Windows, and Windows Vista are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omiss
Summary of the content on the page No. 3
Chapter I. Introduction 1.1 Features Multilingual OSD adjustment Compatible with IBM VGA, extended VGA, VESA VGA, SVGA, XGA, and SXGA modes Wide range of applicable voltages (AC 100-240V 50/60Hz ) enables direct use without any setting. Plug-and-play VESA DDC1/ 2B Standard. Compatible with Windows 9x / 2000 / XP / 7 / Vista operation systems 1.2 Check list Please make sure the following items are included with your LCD monitor; The monitor (and the pedestal) Lower stand
Summary of the content on the page No. 4
Chapter II. Installation 2.1 Install the pedestal Please follow the steps illustrated below to install the pedestal. 3
Summary of the content on the page No. 5
2.2 Connect your monitor to your computer 1. Power off and unplug your computer. 2. Connect the 15-Pin ends of the signal cable to the VGA port of your monitor and the VGA OUT jack on the back of your computer. Secure the screws on both ends of the signal cable. 3. Connect the round end of power adapter to the monitor, then connect one end of the power cords to the power adapter and the other end to the nearest electrical outlet. 4. Power on your computer and monitor. If your monitor
Summary of the content on the page No. 6
2.3 Disconnect the pedestal for shipping Press the clip button on the pedestal and remove the pedestal from the stand. 5
Summary of the content on the page No. 7
Chapter III. Monitor overview Overview of front panel controls 6
Summary of the content on the page No. 8
Chapter IV. Operational Instruction 4.1 Power ON/OFF Switch Press this button to power on/off your monitor. Note: The ON/OFF switch does not disconnect your monitor from the main voltage. To completely disconnect the main voltage, please remove the power plug from the socket. 4.2 Power indicator The power LED is blue when the monitor operates normally. If the monitor runs in power-saving mode, this indicator changes to amber. When the monitor is turned off, this indicator is unlit.
Summary of the content on the page No. 9
4.4 OSD operational instructions Main menu Icon Submenu option Note option To adjust the brightness level of the Brightness screen. The factory default range is 90. To adjust the contrast level of the Contrast screen.The factory default range is 80. Selects the screen color.The Color factory is 6500K or Custom color,depending on the mode. Changes color to slightly reddish Warm- 5000K white. Standard- 6500K Uses standard colors (default). Change color to sl
Summary of the content on the page No. 10
characters (only applicable to VGA input) To adjust the horizontal position of Horizontal position an image (only applicable to VGA input). To adjust the vertical position of an Vertical position image (only applicable to VGA input). Selects the method on how displayed information on the monitor will be formatted.Select Fill to Screen – image fills the entire screen and may look distorted or Custom Scaling elongated because of non-proportional scaling of height an
Summary of the content on the page No. 11
“30 seconds”. To select the function of power Management management for your monitor. To enable the energy-saving function, Select Power Saver On off The factory default setting is On. Restores power to the monitor following an unexpected removal of power. Select: Power-On Recall On Off The factory default is On. The resolution, refresh rate and frequency information will be displayed when the OSD main Mode Display menu is accessed. Please select “On”
Summary of the content on the page No. 12
Set current time – to set the current time in hours and minutes. Set sleep time – to set the desired time when your monitor works under the sleeping mode. Set On time – to set the desired time when your monitor is awakened from the sleeping mode. Timer - Set “On’ or “Off” status for the Sleep Timer. The default setting is “Off”. Sleep Now – to activate the sleep mode for your monitor Selects the language in which the Language OSD menu is displayed.The factory def
Summary of the content on the page No. 13
Chapter V. Technical Information 5.1 Factory preset display mode Criteria Resolution Horizontal frequency Vertical frequency 1 640X480 @60 Hz 31.469 59.94 2 720X400 @70 Hz 31.469 70.087 3 800X600 @60 Hz 37.879 60.317 4 1024X768 @60 Hz 48.363 60.004 5 1280X720 @60 Hz 45.00 60.00 6 1280X1024 @ 60 Hz 63.981 60.02 7 1440X900 @60 Hz 55.935 59.887 8 1600X900 @60 Hz 60.00 60.00 9 1680X1050@60 Hz 65.29 60.00 10 1920X1080@ 60Hz 67.50 60.00 Note: The factory preset
Summary of the content on the page No. 14
5.2 Product specifications Size 23.6" wide screen Max. resolution 1920 x 1080 @ 60 Hz Recommended resolution 1920 x 1080 @ 60 Hz Horizontal frequency 24-94 kHz Vertical frequency 50-76 Hz Viewable size 521.28x 293.22 mm Viewable angle 170 (H) 160 (V) Pitching angle -5º to 15º Pixel frequency 170 MHz OSD functions Brightness, Contrast, Image Control, Languages, Color, Management, Information, Factory Reset, Input Control, Exit, Size (Packing) 630 (L) x 119(W) x 479 (H) mm
Summary of the content on the page No. 15
5.3 Signal cable connector PIN Signal 1 Red Signal 2 Green Signal 3 Blue Signal 4 Ground 5 Cable testing 6 Red Signal Ground 7 Green Signal Ground 8 Blue Signal Ground 9 5 VDC 10 Null 11 Ground 12 SDA (for DDC) 13 Horizontal synchronization 14 Vertical synchronization 15 SCL (for DDC) VGA Interface 14
Summary of the content on the page No. 16
PIN SIGNAL 1 TMDS Data 2 - 2 TMDS Data 2 + 3 TMDS Data 2 / 4 Shield 4 TMDS Data 4 - 5 TMDS Data 4 + 6 DDC Clock 7 DDC Data 8 No Connect 9 TMDS Data 1 - 10 TMDS Data 1 + 11 TMDS Data 1 / 3 Shield 12 TMDS Data 3 - 13 TMDS Data 3 + 14 +3.3/+5V Power (from PC) 15 Ground (Return for +5V) 16 Hot Plug Detect 17 TMDS Data 0 - 18 TMDS Data 0 + 19 TMDS Data 0 / 5 Shield 20 TMDS Data 5 - 21 TMDS Data 5 + 22 TMDS Clock Shield 23 TMDS Clock + 24 TMDS Clock - DVI Interface 5.4 P
Summary of the content on the page No. 17
A Safety and Maintenance Guidelines Important Safety Information A power cord is included with the monitor. If another cord is used, use only a power source and connection appropriate for this monitor. For information on the correct power cord set to use with the monitor, refer to the “Power Cord Set Requirements” section in Agency Regulatory Notices. Warning! To reduce the risk of electric shock or damage to the equipment: • Do not disable the power cord grounding feature. T
Summary of the content on the page No. 18
Safety Precautions Use only a power source and connection compatible with this monitor, as indicated on the label/ back plate of the monitor. Be sure the total ampere rating of the products connected to the outlet does not exceed the current rating of the electrical outlet, and the total ampere rating of the products connected to the power cord does not exceed the rating of the power cord. Look on the power label to determine the ampere rating (Amps or A) for each device. Ins
Summary of the content on the page No. 19
Maintenance Guidelines To enhance the performance and extend the life of your monitor: ● Do not open your monitor cabinet or attempt to service this product yourself. Adjust only those controls that are covered in the operating instructions. If your monitor is not operating properly or has been dropped or damaged, contact your HP authorized dealer, reseller, or service provider. ● Use only a power source and connection appropriate for this monitor, as indicated on the label/ back pla
Summary of the content on the page No. 20
B Agency Regulatory Notices Federal Communications Commission Notice European Union Regulatory Notice Korean Notice Japanese Notice Power Cord Set Requirements The monitor power supply is provided with Automatic Line Switching (ALS). This feature allows the monitor to operate on input voltages between 100–120V or 200–240V. The power cord set (flexible cord or wall plug) received with the monitor meets the requirements for use in the country where you purchased the equip
