Summary of the content on the page No. 1
User’s Guide
W2600H
W2600HP
Make sure to read the Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for future reference.
See the label attached on the product and give the information to your
dealer when you ask for service.
Summary of the content on the page No. 2
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national stan
Summary of the content on the page No. 3
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures wh
Summary of the content on the page No. 4
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand base or Removing the stand base 1. Place the monitor with its front facing downward on a cushion or soft cloth. 2. Align the hooks on the Stand Body with the matching slots in the Stand Base. 3. Insert the hooks into slots. Hook Stand Body Stand Base Slot Warning The tape and locking pin may only be removed from those mon
Summary of the content on the page No. 5
Connecting the Display 4. Attach the monitor to the Stand Base by turning the screw to the right. Screw : Turn the screw by using the screw handle. 5. Lift and turn the monitor to face towards the front after the connection is made to the female part of the cable you're attaching. 6. Take the screw out by turning to the left to separate the monitor and Stand Base. Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture
Summary of the content on the page No. 6
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5˚~20˚ Swivel Range : 350˚ Height Range : maximum 3.94 inch (100.0mm) 100.0mm * Please be sure to remove the Locking pin to adjust the height. Ergonomic You do not need to
Summary of the content on the page No. 7
Connecting the Display Using the Computer 1. Make sure to turn off the computer and product. 1 Connect signal cable and power cord in order, then tighten the screw of 2 the signal cable. A Connect D-sub Cable (PC) B Connect D-sub Cable (Mac) C Connect DVI-D Cable NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. Signal Cable Power Cord 1 2 Varies according to model. Mac adapter For
Summary of the content on the page No. 8
Connecting the Display Connecting the USB(Universal Serial Bus) Cable "USB (Universal Serial Bus)" is an innovation in connecting your different desktop peripherals conveniently to your computer. By using the USB, you will be able to connect your mouse, keyboard, and other peripherals to your display instead of having to connect them to your computer. This will give you greater flexibility in setting up your system. USB allows you to connect a chain of up to 120 devices on a single USB port; an
Summary of the content on the page No. 9
Connecting the Display To arrange the cables Connect the power cord and the signal cable as shown in the figure and then fix them to the cable holders 1 and 2. 1. Please insert the cable holder1 2. Please put the power cord and into the hole. the signal cable in the cable holder 1. Cable holder 1 3. Please put the power cord and the signal cable in the cable holder 2. While pressing the bottom of cable holder 2 with one hand, pull the top of it with the other hand as shown in the picture.
Summary of the content on the page No. 10
Control Panel Functions Front Panel Controls At the current display, Use 'EZ Zooming' Key, then the display ZOOMING resolution is transferred to the one step low resolution. Use 'EZ Zooming' Key one more, the display is back to the original display. Those with poor eyesight such as the elderly, those who have difficulty using computers and children can enlarge text or pictures by adjusting resolution with a single touch. To use this feature, please install forteManager program in the enclosed C
Summary of the content on the page No. 11
Control Panel Functions Use these buttons to select or adjust functions in the On Buttons Screen Display. For more information, refer to page A17. Use this button to make D-Sub or DVI connector active. This feature is used when two computers are connected (SOURCE Hot key) to the display. The default setting is D-Sub. Use this button to enter a selection in the On Screen AUTO/SET Display. Button AUTO IMAGE ADJUSTMENT When adjusting your display settings, always touch the AUTO/SET button before e
Summary of the content on the page No. 12
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments. To make a
Summary of the content on the page No. 13
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu Sub-menu A D Reference BRIGHTNESS PICTURE To adjust the brightness, contrast and gamma of the CONTRAST screen GAMMA sRGB COLOR To customize the color of PRESET 6500K the screen 9300K RED GREEN BLUE To adjust the position of the HORIZONTAL screen POSITION VERTICAL CLOCK To improve the clarity and PHASE TRACKING stabilit
Summary of the content on the page No. 14
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Touch the MENU Button, then the main menu of the OSD appears. Menu Name PICTURE Sub-menus Icons Button Tip MENU : Exit : Adjust (Decrease/Increase) D D E E SET : Enter : Select another sub-menu NOTE OSD (On Screen Display) menu languages on t
Summary of the content on the page No. 15
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PICTURE PICTURE BRIGHTNESS To adjust the brightness of the screen. To adjust the contrast of the screen. CONTRAST GAMMA Set your own gamma value. : -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display high contrast images. MENU : Exit : Decrease : Increase SET : Select another sub-menu COLOR Select the screen color. PRESET • sRGB: Set the screen color to fit the COLOR S
Summary of the content on the page No. 16
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description POSITION POSITION HORIZONTAL To move image left and right. VERTICAL To move image up and down. MENU : Exit : Decrease : Increase SET : Select another sub-menu TRACKING TRACKING CLOCK To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. PHASE To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpe
Summary of the content on the page No. 17
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description LANGUAGE To choose the language in which the control names are displayed. SETUP OSD To adjust position of the OSD window POSITION on the screen. WHITE If the output of the video card is different BALANCE the required specifications, the color level may deteriorate due to video signal distortion. Using this function, the signal level is adjusted to fit into the standard output level of the video card in order to provi
Summary of the content on the page No. 18
On Screen Display(OSD) Selection and Adjustment The OSD screen will appear when you touch the button on the front of the monitor. Menu Name Icons Sub-menu Name FLATRON F-ENGINE Screen when applied Screen when not applied When you execute F-ENGINE, two tones will appear on the screen as shown. The applied screen will appear on the left side, whereas the non-applied screen will appear on the right side. Touch the SET button to use the adjusted screen. Main menu
Summary of the content on the page No. 19
Troubleshooting Check the following before calling for service. No image appears No image appears Is the power cord of the • Check and see if the power cord is connected display connected? properly to the power outlet. Is the power indicator • Touch the Power button. light on? • Adjust the brightness and the contrast. Is the power on and the power indicator blue or green? Is the power indicator • If the display is in power saving mode, try moving the mouse or pressing any key on the keyb
Summary of the content on the page No. 20
Troubleshooting Display image is incorrect Display Position is • Touch the AUTO/SET button to automatically incorrect. adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. • Touch the AUTO/SET button to automatically On the screen adjust your display image to the ideal setting. background, vertical If the results are unsatisfactory, decrease the bars or stripes are vert
