Summary of the content on the page No. 1
MultiSync FP1375X
User’s Manual
Summary of the content on the page No. 2
Declaration Declaration of the Manufacturer We hereby certify that the colour monitor MultiSync FP1375X (NSZ3101STTUW) is in compliance with Council Directive 73/23/EEC: - EN 60950 Council Directive 89/336/EEC: - EN 55022 - EN 61000-3-2 - EN 61000-3-3 - EN 55024 and marked with NEC-Mitsubishi Electric Visual Systems Corporation 4-13-23, Shibaura, Minato-Ku Tokyo 108-0023, JAPAN English-1 English
Summary of the content on the page No. 3
Safety Instruction WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK • DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE COVER (OR BACK). NO USER SE
Summary of the content on the page No. 4
Canadian Department of Communications Compliance Statement DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CSA C22.2 #950. FCC Information 1. Use the attached specified cables with the MultiSync FP1375X colour monitor so as not to interfere with radio and television reception. (1) Please use the supplied power cable or equivalent to e
Summary of the content on the page No. 5
Contents Your new MultiSync FP1375X monitor box* should contain the following: • MultiSync FP1375X Monitor with tilt/swivel base • Power cord for E.U. • Power cord for U.K. • Video Signal Cable (VGA to DVI-A) • Video Signal Cable (DVI-D to DVI-D) • User’s Manual • USB cable • CD-ROM: Includes complete User’s Manual in PDF format and Windows related files (INF file and colour profile). To see the complete User’s Manual, Acrobat Reader 4.0 must be installed at your PC. User’s Manual Video Signal C
Summary of the content on the page No. 6
Quick Start To attach the MultiSync FP1375X monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. If necessary, install the display card into your system. For more information, refer to the display card manual. 3. For the PC Analog output: Connect the VGA to DVI-A signal cable to the connector of the display card in your system (Figure A.1). Tighten all screws. For the PC with DVI digital output: Connect the DVI-D to DVI-D signal cable to the connector of
Summary of the content on the page No. 7
® 4. The Windows 95/98/2000/Me INF file for your MultiSync monitor can be found on the CD-ROM, delivered with the monitor. 5. Connect one end of the power cord to the MultiSync FP1375X monitor and the other end to the power outlet (Figure C.1). 6. Turn on the monitor (Figure D.1). 7. Turn on the Computer. NOTE: If you have any problems, please refer to the Troubleshooting section of this User’s Manual. DVI-A Detachable Signal Cable (VGA to DVI-A) Mac Adapter VGA Computer (not included) Figure B.
Summary of the content on the page No. 8
Controls OSM (On-Screen Manager) control buttons on the front of the monitor function as follows: Sub-Menu Main Menu EXIT Exits to the OSM main menu. Exits the OSM menu. CONTROL / Moves the highlighted Moves the highlighted area area up/down to select up/down to select one of the one of the controls. controls. CONTROL -/+ Moves highlighted area Moves the bar in the - or + left/right to select one of direction to decrease or the controls. increase the adjustment. PROCEED Only executes control o
Summary of the content on the page No. 9
Degauss: Eliminates the build-up of stray magnetic fields which alter the correct scan of the electron beams and affect the purity of the screen colours, focus, and convergence. When activated, your screen image will jump and waver a bit as the screen is demagnetised. Caution: Please allow a minimum of 20 minutes to elapse between uses of the Degauss function. Size and Position Controls Auto Adjust: Automatically adjust the horizontal and vertical size and position settings for applicable timing
Summary of the content on the page No. 10
Sides Left/Right (pincushion balance): Decreases or increases the curvature of the sides either to the left or right. Sides Tilt (parallelogram): Decreases or increases the tilt of the sides either to the left or right. Sides Align (trapezoidal): Decreases or increases the bottom of the screen to be the same as the top. Rotate (raster rotation): Rotates the entire display clockwise or counterclockwise. Tools 1 Moiré Canceler: Moiré is a wavy pattern which can sometimes appear on the screen. The
Summary of the content on the page No. 11
GlobalSync Control: Eliminates picture impurities that may result from the earth’s magnetic field. While in the sub-menus (GLOBALSYNC, TOP LEFT, TOP RIGHT, BOTTOM LEFT or BOTTOM RIGHT), use the –/+ control buttons to fine tune the GlobalSync corrections. Note: NEC recommends that you perform GlobalSync correction while running a typical application such as a spreadsheet or text document. Auto Save: The monitor automatically saves the last settings of the user controls. Factory Preset: Selecting
Summary of the content on the page No. 12
NOTE: For standard systems and graphics boards, keep the factory setting at ENABLE. EdgeLock Control: Operating your monitor at a non-standard timing may cause images to appear darker than normal or have colour distortion. Use of the EdgeLock control will adjust images to their normal state. Video Detect: Selects the method of video detection when more than one computer is connected. NONE: The monitor will not search the other video input port unless the monitor is turned on. FIRST DETECT: The v
Summary of the content on the page No. 13
Recommended use Safety Precautions and Maintenance: FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTISYNC FP1375X COLOUR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water. • Do not insert objects of any kind into the c
Summary of the content on the page No. 14
• Allow adequate ventilation around the monitor so that heat can properly dissipate. Do not block ventilated openings or place the monitor near a radiator or other heat sources. Do not put anything on top of monitor. • The power cable connector is the primary means of detaching the CAUTION system from the power supply. The monitor should be installed close to a power outlet which is easily accessible. • Handle with care when transporting. Save packaging for transporting. CORRECT PLACEMENT AND AD
Summary of the content on the page No. 15
Specifications Monitor Specifications MultiSync FP1375X Notes Picture Tube Diagonal: 55 cm/22 inch 90° deflection, 0.24 mm grill Viewable Image Size: 508 mm/20 inch pitch, medium short persistence phosphor, aperture grille CRT, multi-layered, anti-static screen coating, semi-dark-tint screen and OptiClear screen surface. Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync. TTL Level Horizontal sync. Positive/Negative Vertical sync. Positive/Negative Composite sync. (Positive/Negati
Summary of the content on the page No. 16
Monitor Specifications MultiSync FP1375X Notes Environmental Considerations +10 °C to +35 °C Operating Temperature: 30% to 80% Humidity: 0 to 3,000 m Altitude: Storage Temperature: -20 °C to +60 °C 10% to 90% Humidity: 0 to 13,700 m Altitude: NOTE: Technical specifications are subject to change without notice. English-15 English
Summary of the content on the page No. 17
Features Flat Aperture Grille CRT: Delivers an unparalleled viewing experience with a virtually flat image, eliminating distortion and reducing glare so that what you see on-screen is what you get on your printed output. The striped phosphor alignment of the CRT delivers superior vertical definition with improved bright-ness for more uniform image contrast. OptiClear Screen Surface: Reduces reflection and glare and increases contrast without sacrificing focus level, clarity or brightness. Along
Summary of the content on the page No. 18
Reduced Magnetic Field Technology: Reduces magnetic and alternating electric field emissions and static electricity, addressing ergonomic concerns regarding potential risks from extended computer monitor use. Multiple Frequency Technology: Automatically adjusts monitor to the display card’s scanning frequency, thus displaying the resolution required. FullScan Capability: Allows you to use the entire screen area in most resolutions, significantly expanding image size. GlobalSync /Corner Purity Co
Summary of the content on the page No. 19
Monitor Troubleshooting No picture • Display card should be completely seated in its slot. • Power Button and computer power switch should be in the ON position. • Signal cable should be completely connected to display card/ computer. • Check connector for bent or pushed-in pins. Image is scrolling or unstable • Signal cable should be completely attached to the computer. • Check pin assignments and signal timings of the monitor and your display card with respect to recommended timings and pin as
Summary of the content on the page No. 20
Display image is not centered, too small, or too large • Use the OSM Size and Position Controls to adjust the image. Thin horizontal lines appear on your screen • Thin horizontal lines are normal for an aperture grille CRT and are not a malfunction. These are shadows from the damper wires used to stabilize the aperture grille and are most noticeable when the screen’s background is light (usually white). Black vertical lines are visible on the screen • Thin vertical black lines on one or both sid
