Summary of the content on the page No. 1
CS II Manual LAYOUT#2304 3/25/99 11:16 AM Page 50
™
Planar Clean Screen II PC
User’s Manual
Model Number C3215
Summary of the content on the page No. 2
CS II Manual LAYOUT#2304 3/25/99 11:15 AM Page T1 ™ PLANAR CLEAN SCREEN II PC Integrated Computer with LCD Color Display USER’S MANUAL Model Number C3215 and Options Document Part Number C3DOC-2 Copyright 1999 © Planar Display Solutions. All rights reserved.
Summary of the content on the page No. 3
CS II Manual LAYOUT#2304 3/25/99 11:15 AM Page ii The information in this document is subject to change without notice. This publication may not be reproduced, stored in a retrieval system, or transmitted by any means without prior written permission of Planar Display Solutions. Clean Screen is a trademark and Planar and The Definition of Quality are registered trademarks of Planar Display Solutions. IBM is a registered trademark of International Business Machines Corporation. MS-DOS is a r
Summary of the content on the page No. 4
CS II Manual LAYOUT#2304 3/25/99 11:16 AM Page iii REGULATORY INFORMATION U.S. Federal Communications Commission (FCC) Requirements The Planar Clean Screen II PC has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide rea- sonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
Summary of the content on the page No. 5
CS II Manual LAYOUT#2304 3/25/99 11:16 AM Page iv Duration of Warranty The goods sold hereunder are warranted for a period of two years from date of shipment unless otherwise agreed to by Buyer and Planar. No extension of the warranty will be given during the time the goods are in Planar’s possession. Place of Repair or Replacement In order to obtain service under this warranty, Buyer must notify Planar of the defect before expiration of the warranty period and request a “Return Material Aut
Summary of the content on the page No. 6
CS II Manual LAYOUT#2304 3/25/99 11:16 AM Page v Table of Contents Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii U.S. FCC Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii Canadian Emissions Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii Warranty Information . . . . . . . . . . . . . . .
Summary of the content on the page No. 7
CS II Manual LAYOUT#2304 3/25/99 11:16 AM Page vi Table of Contents Chapter Four: System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Connecting the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Connecting Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 PC Card Port . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 8
CS II Manual LAYOUT#2304 3/25/99 11:16 AM Page vii Table of Contents REFERENCE GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Appendix A: Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 LCD Support . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 9
CS II Manual LAYOUT#2304 3/25/99 11:16 AM Page viii INSTALLATION GUIDE Before You Begin Installing and setting up your Clean Screen II PC is very straightforward. But before you get started, there are some things you should know. What’s in the box? Each box will contain a Planar Clean Screen II head (that is, the integrated computer and LCD display), three Torx drivers (sizes: T15, T20, T25), the external power supply, and the power cord. Remove the equipment carefully and inspect for damage
Summary of the content on the page No. 10
CS II Manual LAYOUT#2304 3/25/99 11:16 AM Page ix Clean Screen II Mounts and Accessories P/N 12" wall mounted swing arm M3S12 Flush wall mount system (for head and keyboard cabinet) M3WC0 Flush wall mount system (head only) M3FHM Roll stand only M3POLE Roll stand with UPS M3POLE-PS2 IS Manager’s Kit C3DOC-2 IS Manager’s Kit, TOUCH C3DOC-TS Keyboard cabinet with keyboard and mouse M3W00 External floppy drive C3FLOP Safety Instructions Your Planar Clean Screen II PC has been designed, assemble
Summary of the content on the page No. 11
CS II Manual LAYOUT#2304 3/25/99 11:16 AM Page x Front Panel Power-on Light Hard Disk Figure 1 Connections (Bottom) USB 1 COM A Power Switch USB 2 LAN COM B Power AT Floppy PC Card Connector Keyboard Connector Slot Figure 2 x Planar Clean Screen II PC User’s Manual
Summary of the content on the page No. 12
CS II Manual LAYOUT#2304 3/25/99 11:16 AM Page 1 Chapter One: The Installation Express If you are an experienced technician who has installed Clean Screen II PCs, then check out Chapter One: The Installation Express. It covers the major steps. If you are the least bit unsure of any step, please resume reading the rest of the manual. 1. Review the Before You Begin section of the manual — especially its Safety Instructions. 2. Unpack the Clean Screen II PC and save the packing. 3. If you need
Summary of the content on the page No. 13
CS II Manual LAYOUT#2304 3/25/99 11:16 AM Page 2 Chapter Two: The Clean Screen II PC Welcome ® Thank you for purchasing Planar’s Clean Screen II color LCD personal computer, an IBM com- patible PC integrated with a full color LCD VGA display. The Clean Screen II PC combines ® ® Intel Pentium performance with state-of-the-art display technology to offer the most advanced, rugged, and lightweight PC system commercially available. Figure 3 — Planar Clean Screen II with keyboard cabinet. Clean S
Summary of the content on the page No. 14
CS II Manual LAYOUT#2304 3/25/99 11:16 AM Page 3 The Clean Screen II PC does not include an integrated floppy disk. There is provision for externally accessing a floppy disk drive through a custom connector. This is for diagnostic and service use only. Front Panel Power-on Light Hard Disk Figure 4 Connections (Bottom) USB 1 COM A Power Switch USB 2 LAN COM B Power AT Floppy PC Card Connector Keyboard Connector Slot Figure 5 Chapter Two: The Clean Screen II PC 3
Summary of the content on the page No. 15
CS II Manual LAYOUT#2304 3/25/99 11:16 AM Page 4 Back Housing Twelve T25 Torx screws Four holes for standard 10 Planar mounting options ( ⁄32) Three T20 Torx screws Figure 6 — Remove the back housing to gain access to the unit. Inside HDD Touch Controller Board (Optional) Memory Battery PC Card CPU Slot Fuse Figure 7 4 Planar Clean Screen II PC User’s Manual
Summary of the content on the page No. 16
CS II Manual LAYOUT#2304 3/25/99 11:16 AM Page 5 Do not remove the T-Bar or the standoffs. Their removal is not necessary to install or replace the battery, hard disk, memory, or fuse. The display unit contained beneath the motherboard uses high voltages. The display unit is not field serviceable and its connections are easily damaged. Static sensitive equipment. Use proper grounding procedures while working inside the Clean Screen II. Chapter Two: The Clean Screen II PC 5
Summary of the content on the page No. 17
CS II Manual LAYOUT#2304 3/25/99 11:16 AM Page 6 Chapter Three: Hardware Installation and Replacement This chapter refers to installing or replacing options within the Clean Screen II itself. Instructions on installing the Clean Screen II onto a standard Planar mounting option will come with the mounting equipment itself. Removing the Back Housing Twelve T25 Torx screws Four holes for standard 10 Planar mounting options ( ⁄32) Three T20 Torx screws Figure 8 Power down unit first and discon
Summary of the content on the page No. 18
CS II Manual LAYOUT#2304 3/25/99 11:16 AM Page 7 Installing Memory Memory Slot with Memory Installed Figure 9 Do not remove the T-Bar or standoffs. To remove a memory module 1. Remove back housing as above. 2. Placing your hands on both sides of the T-Bar, gently open both side catches simultaneously (apply pressure to the plastic part of the catch, not the metal spring). 3. The module will pop up. 4. Remove the memory module. To install a memory module 1. Remove back panel as above. 2. Plac
Summary of the content on the page No. 19
CS II Manual LAYOUT#2304 3/25/99 11:16 AM Page 8 Memory Map Range CPU address Region Cached 0 to 640K 00000000-0009FFFF DRAM yes 640K to 768K 000A0000-000BFFFF VGA memory no 768K to 816K 000C0000-000CBFFF Shadowed VGA BIOS yes 816K to 896K 000CC000-000DFFFF ISA bus or UBE yes 896K to 1M 000E0000-000FFFFF Shadowed System ROM BIOS yes 1M to 16M 00100000-00FFFFFF DRAM yes If no DRAM, ISA or PCI memory no 16M to 64M 01000000-0FFFFFFF DRAM yes If no DRAM, PCI no 64M to (4.0G–512K) 10000000-FFF7FF
Summary of the content on the page No. 20
CS II Manual LAYOUT#2304 3/25/99 11:16 AM Page 9 Replacing the Hard Disk Drive HDD mounting location HDD Power HDD Interface Cable Figure 10 Removing the existing hard disk 1. Remove the back housing as above. 2. Locate the hard disk. 3. Remove the four screws that secure the hard disk to the hard disk cage. 4. Gently detach the hard disk power and I/O cable from the hard disk. 5. Slide the hard disk out of the cage. Installing the new hard disk 1. Slide the hard disk into the cage so its fo
