Summary of the content on the page No. 1
Philips 180P Electronic User's Manual
file:///D|/Philips LCD/english/180P/Index.htm [1/20/2001 3:19:10 PM]
Summary of the content on the page No. 2
Safety & Troubleshooting Safety and Troubleshooting Information Safety Precautions and Maintenance • Installation Locations • Correct Handling of the LCD Monitor • FAQs • Troubleshooting • Regulatory Information • Other Related Information Safety precautions and maintenance WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards, and/or mechanical hazards. Read and follow these instructions when con
Summary of the content on the page No. 3
Safety & Troubleshooting ❍ Temperature: 5-35°C 41-95°F ❍ Humidity: 20-80% RH ● Do not subject the LCD monitor to severe vibration or high impact conditions. Do not place the LCD monitor inside a car trunk. ● Take care not to mishandle this product by either knocking or dropping during operation or transportation. ● Do not store or use the LCD monitor in locations exposed to high humidity or a dusty environment. Also do not allow water or other liquids to spill on or into the LCD monito
Summary of the content on the page No. 4
Safety & Troubleshooting equipment. RETURN TO TOP OF THE PAGE file:///D|/Philips LCD/english/180P/SAFETY/SAFETY.HTM (3 of 3) [1/20/2001 3:19:21 PM]
Summary of the content on the page No. 5
About This Electronic User's Manual About This Electronic User's Manual About This Guide • Other Documents You May Need • Notational Descriptions About This Guide This electronic user's guide is intended for anyone who uses the Philips LCD Monitor. It describes the LCD monitor's features, setup, operation and other pertinent information. Its contents are identical to the information in our printed version. Sections are as follows: ● Safety and Troubleshooting Information provides tips and solu
Summary of the content on the page No. 6
About This Electronic User's Manual Notes, Cautions, and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold or italic type. These blocks contain notes, cautions, or warnings. They are used as follows: NOTE: This icon indicates important information and tips that help you make better use of your computer system. CAUTION: This icon indicates information that tells you how to avoid either potential damage to hardware or loss of data. WARNING: This icon
Summary of the content on the page No. 7
180P Product Information Product Information Product Features • Technical Specifications • Resolution & Preset Modes • Philips Pixel Defect Policy • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views • Attention Signals Product Features 180P ● 18.1" color LCD monitor with excellent display performance, and same viewing size as a 19" CRT monitor. ● Dual input-accepts both DVI Digital and VGA Analog input. ● Advanced AUTO adjustment automatically optimizes pictu
Summary of the content on the page No. 8
180P Product Information Horizontal Frequency 30KHz-82KHz VIDEO • Video dot rate 135MHz • Input impedance - Video 75 ohm - Sync 2 KOhm • Input signal levels 0.7 Vpp Separate sync • Sync input signal Composite sync Sync on green • Sync polarities Positive and negative Dual input : Both Analog (D-Sub) and DVI-D (Digital) are • Video interface available It can be switching via OSD selection. AUDIO • Input signal levels 0.7Vpp • Headphone out signal level 32 ohm 20 + 20 mW • Input
Summary of the content on the page No. 9
180P Product Information • Response time <=50ms (typ.) * These information are subject to change without notice. RETURN TO TOP OF THE PAGE Resolution & Preset Modes • Maximum 1280x 1024 at 75Hz • Recommended 1280x1024 at 60Hz 32USER DEFINABLE MODES 15 factory preset modes: H. freq (KHz) Resolution V. freq (KHz) 31.5 640*350 70 31.5 720*400 70 31.5 640*480 60 35.0 640*480 67 37.5 640*480 75 35.2 800*600 56 37.9 800*600 60 46.9 800*600 75 49.7 832*624 75 48.4 1024*768 60 60 1024*768 75 69.0 11
Summary of the content on the page No. 10
180P Product Information Automatic Power Saving If you have VESA's DPMS compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. And if an input from a keyboard, mouse or other input device is detected, the monitor will automatically "wake up". The following table shows the power consumption and signaling of this automatic power saving features: Power Management Definition VESA Mode Video H-sync V-sync Power Used LED co
Summary of the content on the page No. 11
180P Product Information RETURN TO TOP OF THE PAGE Signal Pin Assignment 1. The digital DVI-D connector contains 24 signal contacts organized in three rows of eight contacts. Signal pin assignments are listed in the table: Pin Pin Pin Signal Assignment Signal Assignment Signal Assignment No. No. No. 1 T.M.D.S. Data2- 9 T.M.D.S. Data1- 17 T.M.D.S. Data0- 2 T.M.D.S. Data2+ 10 T.M.D.S. Data1+ 18 T.M.D.S. Data0+ T.M.D.S. Data2/4 T.M.D.S. Data1/3 T.M.D.S. Data0/5 3 11 19 Shield Shield Shield 4 T.
Summary of the content on the page No. 12
180P Product Information Identical output - connected 4 12 Serial data line (SDA) to pin 10 5 Self test 13 H. Sync / H+V 6 Red video ground 14 V. Sync (VCLK for DDC) 7 Green video ground 15 Data clock line (SCL) 8 Blue video ground RETURN TO TOP OF THE PAGE Views Follow the links to see various views of the monitor and its components. Front View Product Description Attention Signals Attention signal display information and alerts about the status of the monitor. 1. CANNOT DISPLAY THIS VID
Summary of the content on the page No. 13
180P Product Information -- This warning appears when the input signal from your computer is not in a standard video mode or is out of the monitor's scanning range. Solution: For best display performance, reset the display mode of your computer to 1024x768@60Hz for 14" or 15" models and 1280x1024 @60Hz for 17" or 18" models. 2. NO VIDEO INPUT -- This message appears when there is no signal input. Solution: Make sure interface and power cables are properly connected. 3. CHECK CABLE CONNECTI
Summary of the content on the page No. 14
180P Product Information 4. ENTERING SLEEP MODE -- This message appears when monitor is about to enter power saving. To wake up monitor, press any key or click on mouse. 5. WAITING FOR AUTOMATIC ADJUSTMENT -- This message is displayed when the auto adjustment button is pressed. It disappears when automatic adjustments are completed. 6. USE 1024X768 FOR BEST RESULT or USE 1280X1024 FOR BEST RESULT file:///D|/Philips LCD/english/180P/PRODUCT/PRODUCT.HTM (8 of 10) [1/20/2001 3:19:28 PM]
Summary of the content on the page No. 15
180P Product Information -- One of these messages will show up at the top of the OSD main menu when the video signal input mode is not the recommended one. solution: For best performance, reset display. 7. MUTE ON or MUTE OFF These signals appear to indicate audio status after the mute button has been pressed. 8. SECOND VIDEO IS NOT AVAILABLE file:///D|/Philips LCD/english/180P/PRODUCT/PRODUCT.HTM (9 of 10) [1/20/2001 3:19:28 PM]
Summary of the content on the page No. 16
180P Product Information -- This message appears when a user selects a second unavailable video source from the OSD from the INPUT SIGNAL SELECTION menu. -- On systems with both analog and digital output, this screen may appear when a signal other than the default signal type is received. Solution: Use hard keys to switch signal input defautls. 9. THIS IS THE BEST PICTURE SHAPE --This message is displayed when a picture's size is manually extended to the largest screen display size with same
Summary of the content on the page No. 17
Installing your LCD Monitor Installing your LCD Monitor Your LCD Monitor : Front View Product Description • Connecting to Your PC • Getting Started • Optimizing Performance Accessories (optional) : Installing the USB Hub • Installing the Protective Cover • Installing the Wall Mount Kit Front View UP and DOWN buttons are used when adjusting the OSD of your monitor LEFT and RIGHT buttons, like the UP and DOWN buttons, are also used in adjusting the OSD of your monitor. BRIGHTNESS hotkey. When the
Summary of the content on the page No. 18
Installing your LCD Monitor POWER button switches your monitor on MUTE hotkey. When the LEFT and RIGHT arrow buttons are pressed, the sound mute ON or OFF setting will show up. (Option only available for Audio version) Automatically adjust the horizontal position, vertical position, phase and clock setting. RETURN TO TOP OF THE PAGE Optimizing Performance ● For best performance, ensure that your display settings are set at 1024x768@60Hz (for 14"/15") or 1280x1024, 60Hz (for 17"/18"). Note: Y
Summary of the content on the page No. 19
On-Screen Display On-Screen Display Description of the On-Screen Display • The OSD Tree • The OSD Controls Description of the On Screen Display What is the On-Screen Display? This is a feature in all Philips LCD monitors which allows an end-user to adjust screen performance of monitors directly though an on-screen instruction window. The user interface provides user-friendliness and ease-of-use when operating the monitor. Basic and simple instruction on the control keys. On the front controls
Summary of the content on the page No. 20
On-Screen Display RETURN TO TOP OF THE PAGE The OSD Tree Below is an overall view of the structure of the On-Screen Display. You can use this as reference when you want to later on work your way around the different adjustments. file:///D|/Philips LCD/english/180P/OSD/OSDDESC.HTM (2 of 5) [1/20/2001 3:19:33 PM]
