Summary of the content on the page No. 1
PT1510MX
Touchscreen LCD Monitors
USER’S GUIDE
www.planar.com
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Important Recycle Instruction: LCD Lamp(s) inside this product contain mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp specific disposal information check WWW.LAMPRECYCLE.ORG. .
Summary of the content on the page No. 4
Summary of the content on the page No. 5
1 Table of Contents Usage Notice Precautions .........................................................................................2 Introduction About Planar’s PT1510MX..................................................................3 Touch Screen for PT1510MX……………………………………………..4 Package Overview ..............................................................................5 Installation Product Overview.................................................................
Summary of the content on the page No. 6
2 Usage Notice Warning- To prevent the risk of fire or shock hazards, do not expose this product to rain or moisture. Warning- Please do not open or disassemble the product as this may cause electric shock. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit. Do: Turn off the product before cleaning. Touch screen surface may be cleaned using a soft clean cloth moistened with mild window glass c
Summary of the content on the page No. 7
3 Introduction About Planar’s PT1510MX The PT1510MX is a 15” flat panel screen with an active matrix, thin-film transistor (TFT) liquid crystal display (LCD). Features include: Direct Analog signal input Active matrix TFT LCD technology 1024x768 XGA resolution 15” diagonal screen size 31.5 ~ 60 kHz horizontal scan 56 ~ 75 Hz high refresh rate Auto adjustment function Multilingual OSD user controls VESA DPMS power saving Kensington security slot Built-in speakers
Summary of the content on the page No. 8
4 Touch Screen for PT1510MX Gunze analog 5-wire resistive touch screen for finger and stylus input Surface: Anti-glare treatment Interface: Dual RS-232 Serial/USB controller Durability: 35 million touches at a single point Hardness of surface: 2H MIN (As provided in JIS K 5400) Operating force: 0.10~1.96N(10g~200g when using a silicon tipped pen with a 3 mm radius and a hardness of 60 degree.) Transmissivity: 78% (Typ.) Driver: Gunze® Touch Panel Device Driver: TBDD. Supports
Summary of the content on the page No. 9
5 Package Overview LCD Display Power Adapter Power Cord VGA Signal Cable Audio-in Cable USB Cable RS-232 Cable Landing Strip Touchscreen Driver Installation CD-ROM User’s Guide
Summary of the content on the page No. 10
6 Installation Product Overview Front View Back View
Summary of the content on the page No. 11
7 Connector Ports “A” Connector Ports “B” RS-232 USB
Summary of the content on the page No. 12
8 Kensington Security Slot The monitor can be secured to your desk or any other fixed object with Kensington lock security products. The Kensington lock is not included.
Summary of the content on the page No. 13
9 VESA Mount your monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface Standard which defines a physical mounting interface for flat panel monitors, and corresponding standards for flat panel monitor mounting devices, such as wall and table arms. The VESA mounting interface is located on the back of your monitor. To mount the monitor on a swing arm or other mounting fixture, follow the instructions included with the mounting fixture to be used.
Summary of the content on the page No. 14
10 Start Your Installation Remove the Back Cover Please follow these instructions to remove the cover on the back panel of the LCD so that you can connect the cables in “Connector Ports B.” 1. To remove the back cover, follow the arrows in Figure A and press with both your thumbs. The cover should be removed by pressing firmly along the edges while pulling on the cover. 2. Follow the instructions on P. 11 ( Figure 11.1 ) to connect the cables in “Connector Ports B.” 3. Fix the
Summary of the content on the page No. 15
11 Connecting the Display (Figure 11.1, 11.2) To setup this display, please refer to the following figure and procedures. 1. Be sure all equipment is turned off. 2. Connect the DC power cord to the power connector on the monitor; plug one end of the AC power cord into the power adapter, and the other end into an electrical outlet (11.1 ). 3. Connect the VGA signal cable from the display’s VGA input connector to the 15-pin connector of your host computer and tighten the screws (11.1
Summary of the content on the page No. 16
12
Summary of the content on the page No. 17
13
Summary of the content on the page No. 18
14 User Controls Front Panel Controls Control Function No / Icon Menu button Display the OSD menus MENU Select – To select the adjustment items from OSD menus. SELECT/AUTO Select/Auto Auto – To activate the “Auto Adjustment” function to obtain an optimum image. 1. Decreases the brightness of the display Brightness image. Minus/Minus 2. Decreases value of the adjustment items. 1. Increases the brightness of the display Brightness image. Plus/Plus 2
Summary of the content on the page No. 19
15 How to Use the OSD Menus 1. Press the "MENU" button to pop up the “on-screen menu” and to select among the four Main Menus. 2. Choose the adjustment items by pressing the “Select/Auto” button. 3. Adjust the value of the adjustment items by pressing the “ ”or “ “ button. 4. The OSD menu will automatically close, if you have left it idle for a pre-set time.
Summary of the content on the page No. 20
16 On-Screen Display Menus for the PT1510MX Product Main Menu Menu Level 2 Function Description Remark Choose this function to adjust the brightness of the Default 30 Brightness image. Choose this function to adjust the contrast of the Default 40 Contrast image. Minimizes any vertical bars or stripes visible on the LCD Adjustment Clock screen. Minimizes any horizontal distortion and clears or Phase sharpens the displayed characters. H. Position Changes the horizontal posi
