Summary of the content on the page No. 1
OWNER’S MANUAL
PREMIER SERIES HIGH PERFORMANCE
ELECTRIC CONVECTION OVEN
MODELS: m 3000
m 3092
WARNING: FOR YOUR SAFETY:
Improper installation, adjustment, alteration, service Do not store or use gasoline or other flam -
or maintenance can cause property damage, injury mable vapors or liquids in the vicinity of this
or death. Read these installation, operation and or any other appliance.
maintenance instructions thoroughly before install-
ing or servicing this equipment.
For
Summary of the content on the page No. 2
TABLE OF CONTENTS INTRODUCTION ................................................................................................................ ii IMPORTANT ............................................................................................................ ii INSTALLATION, OPERATION & SERVICE PERSONNEL ...................................... ii SHIPPING DAMAGE CLAIM PROCEDURE ........................................................... ii GENERAL .......................................
Summary of the content on the page No. 3
INTRODUCTION IMPORTANT: Service of the equipment should be performed by qualified personnel who are knowledgeable with Safe and satisfactory operation of your equipment Market Forge cooking equipment. depends on proper installation. Installation must conform with local codes, or in the absence of local codes, the Natonal Electrical Code, (ANSI NFPA-70 Latest Edition). Canadian Electrical SHIPPING DAMAGE CLAIM Codes (C.S.A. C22.1). PROCEDURE: Electrical wiring from the Electric Meter, main
Summary of the content on the page No. 4
GENERAL IMPORTANT: SINGLE OVEN: To perform maintenance and repairs of the ap- Assemble the leg/stand assembly as follows: pliance, please contact the factory, factory repre- 1. Remove legs from package. sentative, or the nearest local authorized service 2. Secure top frame parts to the legs with bolts company. provided (long angle - front and back. short an- gle - sides). RATING PLATE: The rating plate is located in front of the oven be- 3. Place the oven on top of leg/stand assembly. low the
Summary of the content on the page No. 5
ASSEMBLY STACKING INSTRUCTIONS MODEL 3092 OVENS STEP 1. Attach (4) foot mounting plates and (4) bullet feet onto bottom ove. Set top oven in place on top of bottom oven and slign them in place. STEP 2. Fasten rear mounting plates as shown. STEP 3. Remove the bottom front trim from top oven and the top front trim from the bottom oven. Fasten front mounting plates as shown. STEP 4. Reattach the front trim pieces to ovens. NOTES: 1.
Summary of the content on the page No. 6
IMPORTANT LEVELING: FINAL PREPARATION: o A carpenter’s level should be placed on the oven’s On initial installation, turn the oven to 250 and op- center baking rack and the unit leveled both front- erate for about 1 hour, then reset the thermostat to to-back and side-to-side. If it is not level, cakes, its maximum and operate for another hour. casseroles, and any other liquid or semi-liquid batter will not bake evenly, and the unit will not At the end of this second hour, turn the thermo- fun
Summary of the content on the page No. 7
CLEANING & MAINTENANCE DAILY CLEANING: with a liquid cleaner designed for this material at OVENS: the end of each day. 1. Remove the baking racks. Wash in hot soapy water and replace after the rest of the oven is DO NOT USE steel wool, abrasive cloths, cleaners cleaned. or powders to clean stainless surfaces. If neces- 2. Scrape off any food particles with a nylon sary to scrape stainless steel to remove encrusted griddle scraper. Be very careful about scraping materials, soak in hot water t
Summary of the content on the page No. 8
SPECIFICATIONS (SINGLE OVEN) MODEL: 3000 CLEARANCE REQUIRED: CLEARANCE REQUIRED: When installing ovens against combustable surfaces 6” (152mm) clearance is required. When installing ovens against combustable surfaces 6” 152mm clearance is required. When installing ovens against non-combustable surfaces (rear or side walls) 0” clearance is required. When installing ovens against non-combustable surfaces (rear or side walls) 0” clearance is required. SERVICE CONNECTIONS Electrically Operated EC E
Summary of the content on the page No. 9
SPECIFICATIONS (STACKED OVEN) MODEL: 3092 CLEARANCE REQUIRED: When installing ovens against combustable surfaces 6” (152mm) clearance is required. When installing ovens against non-combustable surfaces (rear or side walls) 0” clearance is required. SERVICE CONNECTIONS Electrically Operated EC Electrical Connection - Connection for incoming power supply wire on terminal block. EP Power supply - 1 3/8 (44mm) access holes for power supply wires. Use wire suitable for at least 90°C. Nominal a
Summary of the content on the page No. 10
WIRING DIAGRAM 7
Summary of the content on the page No. 11
PARTS LIST 8
Summary of the content on the page No. 12
PARTS LIST ITEM # PART # DESCRIPTOPM QTY. 1 93-0025 MOTOR 1 2 93-0026 MOTOR BRACKET 1 3 93-0021 LIGHT BOX 1 4 93-0022 LIGHT SOCKET 1 5 93-0020 LIGHT BULB 1 6 93-0064 LIGHT COVER 1 8 93-0067 RIGHT SIDE PANEL - REAR 1 9 93-0055 RIGHT SIDE PANEL - FRONT 1 10 93-0017 TERMINAL BLOCK (8-WAY) 1 21 93-0300 MARKET FORGE PREMIER LEXAN DECAL (CONTROL PANEL) 1 22 93-0011 INDICATOR LIGHT 1 23 REF. 93-0023 KNOB - THERMOSTAT 1 24 93-0013 SWITCH, FAN - 2-SPEED 1 93-0014 SWITCH, LIGHT - MOMENTARY OVEN LIGHT SWIT
Summary of the content on the page No. 13
PARTS LIST 44 93-0076 DIVERTER - BOTTOM 1 45 93-0077 DIVERTER - SIDES 1 46 93-0078 DIVERTER - TOP 1 47 93-0074 LEG 6” S/S - WITH ADJUSTABLE FOOT (TSCV-2) 1 48 93-0075 LEG PLATE ASSY. (TSCV-2) 1 52 93-0048 RACK GUIDE - R/H 1 93-0050 RACK GUIDE - L/H 1 53 93-0049 RACK 1 54 93-0069 TOP PANEL 1 56 93-0047 LEG ASSY. (SINGLE UNIT) 1 57 93-0003 FOOT 1 58 93-0072 BOTTOM LEG FRAME - SIDES 1 59 93-0073 BOTTOM LEG FRAME - FRONT & REAR 1 60 93-0007 CASTER W/BRAKES (FRONT) 2 61 93-0006 CASTER W/O BREAKES (RE
Summary of the content on the page No. 14
PARTS LIST Fig. 5 Heating Elements ITEM # PART # DESCRIPTION QTY. 1 98-4066 208 Volt Heating Elements (Nest of Three) 1 Set 2 98-4067 240 Volt Heating Elements (Nest of Three) 1 Set 3 98-4065 480 Volt Heating Elements (Nest of Three) 1 Set ITEM # PART # DESCRIPTION QTY. 1 97-4616 Terminal Block Assy. 1 2 10-5944 Contactor 40 Amp. 50/60 1 Hz (120 Volt) 3 98-4096 Fuse 1 4 98-3685 Wire Harness 1 5 08-6469 Fuse Holder 1 Fig. 6 Terminal Block Contactor & Wire Assembly 11
Summary of the content on the page No. 15
PARTS LIST Fig. 7 Electrical ITEM # PART # DESCRIPTION QTY. 1 98-4098 Electrical Box 6” x 6” x 4” 1 2 98-4092 Transformer, 1KVA 1 12
Summary of the content on the page No. 16
PARTS LIST PREMIER SERIES 1 9 HEAT ON THERMOSTAT 2 0 60 5 55 10 50 3 ITEM # PART # DESCRIPTION QTY. 15 45 20 1 93-0300 Market Forge Premier Lexan Decal 1 40 25 35 30 2 93-0023 Thermostat 60” Capline 1 3 REF.93-0023 Thermostat Knob 1 MODE 4 93-0013 Switch, Fan Hi-Lo 1 5 93-0014 Switch, Light Momentary Oven Light 1 6 93-0012 Switch Power, 3 Positions On/Off 1 5 4 Cooldown HI ON 7 93-0028 Timer Knob 1 8 93-0029 Timer 1 9 93-0011 Indicator Light, 120 Volt 1 LO LIGHT FAN POWER ON OFF COOL DOWN TIMER
