Summary of the content on the page No. 1
35772G
Gas hob
GB
Operating Instructions
Summary of the content on the page No. 2
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 350350 Installation This hob must be installed by qualified personnel, according to the manufacturer’s instructions and to the relevant British Standards. Any gas installation must be carried out by a registered CORGI installer. Remove all packaging before using the hob. Ensure that the gas and electrical supply complie
Summary of the content on the page No. 3
Ensure the control knobs are in the ‘OFF’ position when not in use. When using other electrical appliances, ensure the cable does not come into contact with the hot surfaces of the cooking appliance. Unstable or misshapen pans should not be used on the hob as unstable pans can cause an accident by tipping or spillage. Never leave the hob unattended when cooking with oil and fats. Never use plastic or aluminium foil dishes on the hob. Perishable food, plastic items and areosols may be affec
Summary of the content on the page No. 4
Contents Instructions for the User Important Safety Information 2 Description of the Hob 5 Operation 6 Maintenance and Cleaning 7 Something Not Working? 8 Service and Spare Parts 9 Customer Care 9 Guarantee Conditions 10 Instructions for the Installer Engineers technical data 11 Important safety requirements 12 Installation 13 Electrical connections 17 Wiring diagram 18 Fault Finding 19 Commissioning 22 Conversion from Natural Gas to LPG 23 Guide to Use the instructions The following symbols wi
Summary of the content on the page No. 5
Description of the Hob 4 3 1 5 2 2 Fig. 1 6 1. Hob Top 2. Semi-rapid burner 3. Auxiliary burner 4. Rapid burner 5. Ultra-rapid burner (triple crown) 6. Control knobs Installation Any gas installation must be carried out by a registered CORGI installer, and in accordance with existing rules and regulations. The relevant instructions are to be found in the second section of this manual. Please, ensure that, once the hob is installed, it is easily accessible for the engineer in the event of a break
Summary of the content on the page No. 6
Fig. 2 Operation Hob burners control knobs The symbols on the knobs mean that : there is no gas supply there is maximum gas supply there is minimum gas supply Lighting the burners For easier lighting, proceed before putting a pan on the pan support. To light a burner, turn the relevant knob anticlockwise to FO 0204 maximum position ( ), then push it down to ignite the A - Burner cap burner. Upon ignition, adjust the flame as required. B - Burner crown If the burner does not ignite, turn t
Summary of the content on the page No. 7
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing up liquid has been added. Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for n
Summary of the content on the page No. 8
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. SYMPTOM SOLUTION There is no spark when lighting the gas Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the mains fuse has not blown Check the burner cap and crown have been replaced correctly, e.g. after cleaning. Check the main jet is not blocked and the
Summary of the content on the page No. 9
Service and Spare Parts If you require spare parts or an engineer contact your local Service Force Centre by telephoning: 0870 5 929 929 Your call will be routed to your local Service Force Centre. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.uk When you contact the Service Centre, they will need the following information: 1. Your name, address and post code. 2. Your telephone number 3. Clear and c
Summary of the content on the page No. 10
Guarantee Conditions Standard guarantee conditions We, AEG-Electrolux, undertake that if within 12 months of the date of the purchase this AEG-Electrolux appli- ance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our discretion repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: · The appliance has been correctly installed and used only on the electricity or gas supply stated on the rating pl
Summary of the content on the page No. 11
Instruction for the Installer Engineers technical data Burner Dia. Tap By-pass Overall dimensions 1/100 mm Width: 680 mm Auxiliary 28 Depth: 510 mm Semi-rapid 32 Rapid 40 Cut out dimensions Ultra-rapid 56 Width: 560 mm Depth: 480 mm Aeration adjustment none Supply Connections Semi-rapid Burner 2.0 kW (6824 BTU/HR) Gas:R 1/2 inch (1/2 inch male) Rear right hand Auxiliary Burner 1.0 kW (3413 BTU/HR) corner Appliance class 3 Electric: 230 V 50 Hz supply, 3 core flexible cable with non rewireable
Summary of the content on the page No. 12
100 mm 100 mm 50 mm 50 mm 50 mm 50 mm 600 mm 600 mm Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Part 2 and B.S. 6891 Current Editions. 3 The hob should not be installed in a bed sitting room with a volume of less than 20 m . If it is 3
Summary of the content on the page No. 13
Installation Important This hob must be installed by qualified personnel to the relevant British Standards. Any gas installation must be carried out by a CORGI registered installer. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. On the end of the shaft, which includes the G 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Sc
Summary of the content on the page No. 14
680 Cut Out Size The dimensions of the cut-out are given in the diagram. FO 2038 Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2 (see next page). 14 510
Summary of the content on the page No. 15
2 1
FO 2564 FO 2563 Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture unit, in order to avoid 3 any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in diagram 3. The panel fitted under the hob ("a") should be easily removable to allow easy access if technical assistance is needed. The space behind the kitchen unit ("b") can be used f
Summary of the content on the page No. 16
Fitting the Hob into the worktop Carry out the building in of the hob as follows: • put the seals supplied with the hob, on the edges of the cut out: place them exactly on the front and rear edge and at 50 mm. from the side edges, as shown in the diagram, takingcare that the seals meet without overlapping; • place the hob in the cut out, taking care that it is centred; FO 2753 • fix the hob with the relevant fixing clamps and screws, as shown in the diagram. When the screws have been tightened,
Summary of the content on the page No. 17
Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230-240V 50Hz AC electrical supply. Before switching on, make sure the electricity supply voltage is the same as that indicated on the hob rating plate. The rat
Summary of the content on the page No. 18
Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations. The switch must not break the yellow and green earth cable at any point. Ensure that the hob supply cord does not come into contact with surfaces with temperatures higher than 50 d
Summary of the content on the page No. 19
Blue Brown Green Fault Finding Yellow Preliminary Electrical Systems Check START Blue Isolate appliance Green and carry out: Brown Yellow A: Earth Continuity check. Carry out: NO YES Carry out: D: Resistance to C: Polarity check. Earth check. Has inlet fuse blown? Electricity supply should now be satisfactory. NO YES PLUG (with cover removed) SOCKET (face view) Inlet wiring Earth Wire faulty. Green/Yellow ( ) Rectify any ( ) E fault. Neutral Wire Blue N L Isolate appliance and carry out: B:
Summary of the content on the page No. 20
A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary. — Test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω (Ohm), check all earth wires for continuity and all contacts are clean and tight. B. INSULATION CHECK Appliance electrically disconnected, all switches ON. a) meter set on Ω (Ohms) x 1 scale. Test leads from L to N in appliance terminal block. If meter reads «0
