Summary of the content on the page No. 1
Installation Instructions
KM 400 Electric Cooktop
KM 402 / KM 403 Fryer
KM 408-1 Contact Grill
KM 410 / KM 411 Electric Barbecue
UV
To prevent accidents and
machine damage,
read these instructions
before installation or use. M.-Nr. 05 060 863
Summary of the content on the page No. 2
2
Summary of the content on the page No. 3
Contents IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety distance above the appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Appliance dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 KM 400 / KM 408-1 . . . . . . . . . . . . . . . .
Summary of the content on the page No. 4
IMPORTANT SAFETY INSTRUCTIONS Note to the installer: Please leave this instruction book with the consumer for the local electrical inspector’s use. Installation The minimum distances given in these Installation Instructions must be observed in order to ensure safe operation. Failure to do so increases recommended the risk of fire. To prevent appliance damage, the cabinetry and venting hood should be installed first. The countertop must be bonded with heat resistant (212 °F/100 °C) adhesive to pr
Summary of the content on the page No. 5
IMPORTANT SAFETY INSTRUCTIONS Cooktops should not be installed Safety distance above the appliances above a dishwasher, washer, dryer, freezer or refrigerator. The high temperatures radiated downwards from the cooktops could damage these appliances. This equipment has not been designed for maritime use or for use in mobile installations such as aircraft or recreational vehicles. However, under certain circumstances it may be possible for an installation in these applications. Please contact the
Summary of the content on the page No. 6
Appliance dimensions KM 400 / KM 408-1 a Clamps 3 b Please allow an additional / " 4 (18 mm) depth below the cooktop for clearance of the power cord. 6
Summary of the content on the page No. 7
Appliance dimensions KM 402 / KM 403 a Clamps 7
Summary of the content on the page No. 8
Appliance dimensions KM 410 / KM 411 a Clamps 8
Summary of the content on the page No. 9
Installation Cutting out the countertop Installing one or multiple appliances: Cut out the countertop using the dimensions listed in the following table. Number of Cut out width cooktops Dimension "B" 13 1 10 / " (274 mm) 16 1 2 22 / " (562 mm) 8 7 3 33 / " (850 mm) 16 13 4 44 / (1138 mm) 16 1 5 56 / " (1426 mm) 8 All Miele combisets have the same 1 6 67 / " (1714 mm) 2 length and width. Make sure that there 13 is enough room beneath the countertop 7 78 / " (2002 mm) 16 to allow for the depth of
Summary of the content on the page No. 10
Installation Laying out the support bars and clamps a Clamps c Slight gap between support bar and countertop. b Support bars This illustration shows the layout for 3 combisets, their respective support bars,b, and the 14 spring clamps,a, required for correct installation. If more than 3 combisets are being 3 installed, add an additional 11 / " 8 (288 mm) to the overall width of the cut out for each extra combiset, or use the table on the preceding page. 10
Summary of the content on the page No. 11
Installation Securing the support bars Securing the spring clamps d c Wood or Corian countertops Wood or Corian countertops ^ Arrange the bars,b, as shown in the ^ Place the spring clamps,a, as illustration shown in the illustration. 1 1 ^ Drill / " (1.5 mm) pilot holes through ^ Drill two / " (1.5 mm) pilot holes for 16 16 the brackets and secure them using each clamp and secure using the the supplied screws. supplied screws. ^ Fill the gap,c, between the bars and the countertop using the suppl
Summary of the content on the page No. 12
Installation Locking the appliance into place Make sure the cooktops are aligned correctly before setting them into the countertop. Once the spring clamps are engaged, a special tool is required to release the cooktop from the clamps. ^ Guide the power cord through the cut out and connect the appliance to the electrical supply. ^ Position the cooktop over the cut out. With a hand on each side, above the clamps,a, press the cooktop down, locking it into the spring clamps. Make sure that the cookt
Summary of the content on the page No. 13
Installation Important The cooktop must not be permanently sealed into the countertop when installed. The sealing strip under the edge of the cooktop provides a sufficient seal for the countertop. If the cooktop is sealed into position, the countertop or the appliance may be damaged if the cooktop needs to be removed for maintenance or service. 13
Summary of the content on the page No. 14
Electrical connection Power supply: ,WARNING: – 240 V, 60 Hz, 15 A fuse rating Disconnect the appliance from the main power supply before servicing. or To reduce the risk of electric shock, – 208 V, 60 Hz, 15 A fuse rating make sure that the appliance is properly grounded after installation. The oven is equipped with a power To guarantee the electrical safety of cord consisting of 3 leads. They must this appliance; continuity must exist be connected to a dedicated line between the appliance and
Summary of the content on the page No. 15
15
Summary of the content on the page No. 16
Alterations rights reserved / 0705 M.-Nr. 05 060 863 / 01 en-US
