Summary of the content on the page No. 1
INSTRUCTIONS AND ADVICE FOR THE
USE, INSTALLATION AND MAINTENANCE
OF OUR BUILT-IN ELECTRIC HOB
Dear Customer,
Thank you for having purchased one of our products.
We are certain that this new, modern, functional and practical appliance, built with the very
highest quality materials, will meet your requirements in the best possible way. This appliance is
easy to use. It is, however, important to thoroughly read the instructions in this handbook in order
to obtain the best results.
These instructio
Summary of the content on the page No. 2
DESCRIPTION OF THE HOT PLATES TYPE: PAZ04 1 Normal plate Ø 145 of 1000 W 2 Normal plate Ø 180 of 1500 W 3 Rapid plate Ø 145 of 1500 W 4 Rapid plate Ø 180 of 2000 W 5 Thermostat plate Ø 145 of 1500 W 6 Thermostat plate Ø 180 of 2000 W 7 Control knob for electric plate n° 1 8 Control knob for electric plate n° 2 9 Control knob for electric plate n° 3 10 Control knob for electric plate n° 4 11 Control knob for electric plate n° 5 12 Control knob for electric plate n° 6 13 Warning light indicating
Summary of the content on the page No. 3
USE diagram indicates to which electric plate the knob in 1) SWITCHING ON THE ELECTRIC question corresponds (see fig. 1 - 2). PLATES A red warning light will come on to indicate that the The hobs may be equipped with three types of plate has been ignited. electric plates: normal, thermostat and rapid plates indicated by a red mark. The normal plates and the 2) HOW TO USE THE ELECTRIC rapid plates are controlled by a 7 - position switch (see fig. 1). The thermostat plates are controlled by PLATES
Summary of the content on the page No. 4
USE CLEANING WARNINGS: IMPORTANT: Always disconnect the appliance from the When the plate is switched on for the first time, or electricity main before carrying out any cleaning if it has remained unused for a long period, it operation. should be dried for 30 minutes on switch position n° 1. This will eliminate any moisture that may have 3) HOTPLATE been absorbed by the insulating material. If you want to preserve the surface clean and bright, To correctly use the appliance, remember: periodical
Summary of the content on the page No. 5
INSTALLATION Installation and maintenance must only be - Evenly and securely fix the seal to the hob, carried out by a qualified technician. pressing it into place with the fingers. Incorrect installation could cause damage to - Remove the strip of protective paper from the persons, property and animals for which the seal. Fit the hooks into their relative housings in manufacturer cannot be held responsible. the unit and set the hob into the hole in the Check that the appliance is in a good con
Summary of the content on the page No. 6
CONVERSIONS Disconnect the appliance from the mains supply b) Shift connecting plate on terminal according to prior to any conversions being carried out. the following chart. This chart is also affixed to the hob. 7) CHANGING THE TYPE OF POWER c) Insert a supply cable of adequate section (see SUPPLY chart par. 9) through core hitch on the terminal Although they leave our factory preset for single- board. phase connection, certain appliances may by d) Connect the phase and earth wires to the rela
Summary of the content on the page No. 7
SERVICING Always disconnect the appliance from the longer than “live” ones, and must respect the electricity main before proceeding with any cautions in paragraph “Electrical connection”. servicing operation. To reassemble the appliance repeat the inverse process. 8) REPLACING THE ELECTRICAL 9) TECHNICAL CHARACTERISTICS OF COMPONENTS THE ELECTRICAL COMPONENTS For access to the various parts, remove the hotplate To facilitate the job of the installer we present a from the top of the cabinet. Then
Summary of the content on the page No. 8
TECHNICAL DATA MODEL WITH 2 RAPID PLATES + 2 THERMOSTAT PLATES VOLTAGE 240 V~ FREQUENCY 50/60 Hz TOT. RATING 7000 W MODEL WITH 2 RAPID PLATES + 2 NORMAL PLATES (with protector) VOLTAGE 240 V~ FREQUENCY 50/60 Hz TOT. RATING 6000 W MODEL WITH 3 NORMAL PLATES (with protector) + 1 THERMOSTAT PLATE VOLTAGE 240 V~ FREQUENCY 50/60 Hz TOT. RATING 5500 W 8
