Marshall WOBURN-II-BLUETOOTH user manual

1. Switch on your Marshall Woburn II Bluetooth Speaker.
. Hold down the 'Bluetooth' button for at least 10 seconds until you hear a sound indicating that the speaker has been reset. The 'Bluetooth' button is located on the top panel of the speaker.
3. Once the speaker has been reset, it automatically enters the pairing mode.
4. You can now connect to the speaker with a new device.
Please keep in mind resetting the speaker will remove all previously paired devices and restore the speaker to its factory settings.

To connect your Marshall Woburn II Bluetooth speaker, follow these steps:
1. Power on your Woburn II Bluetooth speaker by turning the volume knob clockwise until it clicks.
. Make sure your Bluetooth-enabled device (such as a smartphone, tablet, or computer) is turned on and has its Bluetooth functionality enabled.
3. On your device, go to the Bluetooth settings menu. This may vary depending on the device, but typically it can be found in the settings or connections menu.
4. In the Bluetooth settings menu, search for available devices or scan for nearby devices. It may take a few moments for your Woburn II to appear on the list.
5. When you see the "Marshall Woburn II Bluetooth" or a similar name, select it to start the pairing process.
6. Once paired, you should hear an audible confirmation sound from the speaker, indicating a successful connection.
7. Adjust the volume on your device and the Woburn II speaker as desired to start streaming audio through the speaker.
Note: In some cases, you may need to enter a pairing code. The default code for the Marshall Woburn II is "0000" (four zeroes). However, this step may not be necessary for most devices.
If you encounter any difficulties, consult the user manual that came with your Woburn II or visit the Marshall Support website for further assistance.

The issue of your Marshall Woburn 2 being connected but not producing any sound may be due to a few reasons. Here are a few troubleshooting suggestions:
1. Check the Connection: Bluetooth connectivity can often be the root cause. Try disconnecting the phone or device from the speaker and re-pairing them. Ensure that your speaker is in range of your audio device.
2. Volume Check: It might be a simple case of the volume being lowered or on mute on either your device or speaker, so check both volumes.
3. Incorrect Audio Output: You may be connected properly, but your audio output device might still be set to your device's speakers, not your Marshall Woburn 2. Check your device's Bluetooth settings to make sure you are sending the audio to the correct output.
4. Restart Devices: Sometimes, ICT issues can be resolved by restarting the electronic devices. Turn both off your Bluetooth device and speaker, wait a few minutes, then turn them on again.
5. Update Bluetooth: If your devices are not updated, it may affect your connectivity. Check if there's an update available for your Bluetooth device's software or firmware.
6. Factory Reset: If all above methods fail, you may have to resort to a factory reset.
If the problem still persists, you may have a hardware issue and should contact Marshall customer support or bring the speaker to a registered technician for further checking.

To connect your Bluetooth device to the Marshall Woburn II Bluetooth speaker, follow these steps:
1. Turn on the Marshall Woburn II Bluetooth speaker by flipping the power switch located at the back of the speaker to the "ON" position.
2. Press and hold the "Source" button on the top panel of the speaker until the Bluetooth indicator on the control panel starts flashing, indicating that the speaker is now in pairing mode.
3. On your Bluetooth device (e.g., smartphone, tablet, laptop), navigate to the Bluetooth settings menu.
4. Enable Bluetooth if it's not already turned on.
5. In the Bluetooth settings menu, search for available Bluetooth devices. The name of the Marshall Woburn II speaker should appear on the list. It will be labeled as "Marshall Woburn II" or something similar.
6. Tap on the name of the speaker to connect to it. You may be prompted to confirm the connection or enter a pairing code. If prompted, follow the on-screen instructions.
7. Once the connection is successful, the Bluetooth indicator on the control panel of the Marshall Woburn II speaker will stop flashing and remain solid. Additionally, your Bluetooth device will show a confirmation that it is connected to the speaker.
Your Bluetooth device is now successfully connected to the Marshall Woburn II Bluetooth speaker. You can start playing your favorite audio through the speaker.