Streszczenie treści zawartej na stronie nr. 1
GL408/412e
PRINTER
OPERATOR MANUAL
PN: 9001163A
Streszczenie treści zawartej na stronie nr. 2
SATO America, Inc. 10350A Nations Ford Road Charlotte, NC 28273 Main Phone: (704) 644.1650 Technical Support Hotline: (704) 644.1660 Technical Support Fax: (704) 644.1661 E-Mail: satosales@satoamerica.com techsupport@satoamerica.com www.satoamerica.com WARNING THE EQUIPMENT REFERENCED IN THIS DOCUMENT COMPLIES WITH THE REQUIREMENTS IN PART 15 OF FCC RULES FOR A CLASS B COMPUTING DEVICE. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA MAY CAUSE UNACCEPTABLE INTERFERENCE TO RADIO AND TV RECEPTIO
Streszczenie treści zawartej na stronie nr. 3
TABLE OF CONTENTS INTRODUCTION About This Manual 1-2 General Description 1-3 Control Features 1-4 TECHNICAL DATA Physical Characteristics 2-2 Enviromental 2-2 Power 2-2 Processing 2-2 Command 2-2 Interface Modules 2-2 Print 2-2 Sensing 2-3 Media 2-3 Ribbon 2-3 Regulatory 2-3 Character Font Capabilities 2-4 Barcode Capabilities 2-5 INSTALLATION Unpacking & Parts Identification 3-2 Printer Installation 3-3 Site Location 3-3 Cable Connection 3-3 Media Selection 3-4 Media & Ribbon Loading 3-4 Operat
Streszczenie treści zawartej na stronie nr. 4
PRINTER CONFIGURATION Printer Configuration 4-2 Configuration Modes 4-3 User Mode 4-3 Configuration Mode 4-4 Advanced Mode 4-5 Serial Interface Mode 4-7 Parallel Interface Mode 4-8 Centronics Interface Mode 4-9 Universal Serial BUS (USB) Interface Mode 4-10 Local Area Network (LAN) Interface Mode 4-11 Wirerless Local Area Network (WLAN) Interface Mode 4-12 PGL Emulation Mode 4-13 ZGL Emulation Mode 4-14 DGL Emulation Mode 4-15 TGL Emulation Mode 4-16 IGL Emulation Mode 4-17 Diagnostics Mode 4-18
Streszczenie treści zawartej na stronie nr. 5
TROUBLESHOOTING Error Signal Troubleshooting 5-2 Troubleshooting Table 5-8 Interface Troubleshooting 5-10 Parallel Interface 5-10 RS232 Serial Interface 5-10 Universal Serial Bus (USB) Interface 5-10 LAN Ethernet Interface 5-11 802.11G Wireless Interface 5-11 Centronics Interface 5-11 Test Print Troubleshooting 5-12 Hex Dump Mode 5-12 Test Label Printing 5-12 Sample Test Label 5-13 MAINTENANCE Cleaning Procedures 6-2 Replacement Procedures 6-3 Print Head 6-3 Fuse 6-4 Media Platen Roller 6-5 Adju
Streszczenie treści zawartej na stronie nr. 6
INTRODUCTION • About This Manual • General Description • Control Features GL408-412e Operator Manual 1-1 PN: 9001163A
Streszczenie treści zawartej na stronie nr. 7
Unit 1: Introduction ABOUT THIS MANUAL This manual is laid out consistent with the product discussed and provides all of the information required for printer installation, configuration, operation, and light maintenance. Refer to this product’s Programming Reference document for instructions on printer programming through a host system. This manual also incorporates the use of special information boxes. Examples of these boxes and the type of information provided in each, are below. WARNING: PR
Streszczenie treści zawartej na stronie nr. 8
Unit 1: Introduction GENERAL DESCRIPTION The GL4e Series printers are specifically designed for use in high-volume, labeling applications demanding great reliability and around the clock operation. It’s aluminum chassis provides the needed corrosion resistance demanded by some industrial applications. The coated interior frame provides strength and stability. The stylish front housing cover and operator panel are both molded of extra-durable, black ABS plastic to not only provide protection ag
Streszczenie treści zawartej na stronie nr. 9
Unit 1: Introduction CONTROL FEATURES This chapter identifies the interactive control features of the printer. These functions are defined generally here. More specific explanations will be found throughout this manual on how to use them. LCD Display Communicates operational conditions via the use of icons and text. LED Indicators POWER Illuminates when the power on. ONLINE Illuminates when communication is available. Flashes when fails. STATUS Flashes when an error occurs. Flashes when send
Streszczenie treści zawartej na stronie nr. 10
TECHNICAL DATA • Physical Characteristics • Environmental •Power • Processing • Command • Interface Modules •Print • Sensing •Media •Ribbon • Regulatory Approvals • Character Font Capabilities • Barcode Capabilities GL408-412e Operator Manual 2-1 PN: 9001163A
Streszczenie treści zawartej na stronie nr. 11
Unit 2: Technical Data PHYSICAL CHARACTERISTICS Width 10.75 Inches (271 mm) Height 12.00 Inches (305 mm) Depth 18.00 Inches (455 mm) Weight 33 Pounds (15 Kg) ENVIRONMENTAL Operating Temperature 41 to 104°F (5° to 40°C) Storage Temperature -4 to 140°F (-20° to 60°C) Storage Humidity 15 to 85% RH Non-Condensing Operating Humidity 15 to 85% RH Non-Condensing POWER Input Voltage 100-120/200-240 Volts AC +/- 10%, 50/60 Hertz +/-5% Maximum: 222 Volts AC, 219 Watts (when print ratio is 50%) Consumptio
Streszczenie treści zawartej na stronie nr. 12
Unit 2: Technical Data SENSING Gap Position & Sensitivity Adjustable Reflective Eye-Mark Position & Sensitivity Adjustable Ribbon Near End Fixed (enabled/disabled) Media Out Fixed (always enabled) Ribbon Out Fixed (always enabled) Cover Open Fixed (always enabled) MEDIA Media Width: 0.87 to 5.04 Inches (22 - 128mm) Width Media Width with Backing Paper: 0.98 to 5.16 Inches (25 - 131mm) Media Length: 0.24 to 15.63 Inches (6 - 397mm) Length (Continous) Media Length with Backing Paper: 0.35 to
Streszczenie treści zawartej na stronie nr. 13
Unit 2: Technical Data CHARACTER FONT CAPABILITIES MATRIX FONTS XU 5 dots W x 9 dots H (Helvetica) XS 17 dots W x 17 dots H (Univers Condensed Bold) XM 24 dots W x 24 dots H (Univers Condensed Bold) GL408e: 15 dots W x 22 dots H OA Font (OCR-A) GL412e: 22 dots W x 33 dots H GL408e: 20 dots W x 24 dots H OB Font (OCR-B) GL412e: 30 dots W x 36 dots H AUTO SMOOTHING FONTS XB 48 dots W x 48 dots H (Univers Condensed Bold) XL 48 dots W x 48 dots H (Sans Serif) VECTOR FONT Proportional or Fixed Spaci
Streszczenie treści zawartej na stronie nr. 14
Unit 2: Technical Data BARCODE CAPABILTIES UPC A/E JAN 8/13 EAN 8/13 Code 39 Code 93 Code 128 Interleaved 2 of 5 Industrial 2 of 5 Linear Bar Codes Matrix 2 of 5 Bookland NW-7 MSI RSS-14 POSTNET UCC/EAN 128 Customer Barcode QR Code Data Matrix Maxi Code Two Dimemsional PDF417 Micor PDF417 Synthetic Symbol Ratios 1:2, 1:3, 2:5, User definable bar widths Bar Height 4 to 999 dots, User progammable Rotation 0, 90, 180, and 270 Degrees Sequential Numbering Sequential numbering of both numerics and b
Streszczenie treści zawartej na stronie nr. 15
INSTALLATION • Unpacking & Parts Identification • Printer Installation • Operational Mode Selection • Interface Selection • Accessories Installation GL408-412e Operator Manual 3-1 PN: 9001163A
Streszczenie treści zawartej na stronie nr. 16
Unit 3: Installation UNPACKING & PARTS IDENTIFICATION Unpack the printer as directed in the following procedure. 1 Place the shipping container (box) upright on a soid, flat surface. 2 Open the box, remove any loose items and the first layer of packing material. 3 Carefully lift the printer and accessories from the box and place them on a solid flat surface. 4 Remove the plastic covers from the packed items and visually inspect for physical damage. 5 Ensure all components are present as dict
Streszczenie treści zawartej na stronie nr. 17
Unit 3: Installation PRINTER INSTALLATION This chapter provides guidance on how to station, connect, and load the printer once unpacked. Following printer setup, procede to the next chapter for information on interface selection. SITE LOCATION • Stationed on a solid flat surface. • Stationed away from hazardous materials. • Stationed within operational distance of the host based on interface specifications. CABLE CONNECTION The diagram below (Figure 3-2) displays the printer’s connectors and p
Streszczenie treści zawartej na stronie nr. 18
Unit 3: Installation MEDIA SELECTION The size and type of the labels or tags to be printed should have been taken into consideration before printer purchase. Ideally, the media width will be equal to, or just narrower than, the print head. Using media that does not cover the print head will allow the platen roller to tread on it and wear it out. The media edge will also wear a groove in the platen roller affecting print quality. MEDIA & RIBBON LOADING There are two general media types that may
Streszczenie treści zawartej na stronie nr. 19
Unit 3: Installation Fan-Fold Media Media Guide Media Holder Media Sensor Rear Housing Cover Media Damper Lower Print Assy Figure 3-3b, Fan-fold Media Loading Ribbon Rewind Spindle Ribbon Core Ribbon Stock Ribbon Supply Spindle Upper Print Assy Figure 3-3c, Ribbon Loading GL408-412e Operator Manual 3-5 PN: 9001163A
Streszczenie treści zawartej na stronie nr. 20
Unit 3: Installation OPERATIONAL MODE SELECTION There are two modes of printer operation; Dispense and Continuous. The difference between the two is the way that the label and paper backing is ejected. Before printer configuration, one must determine which mode will be used. This chapter identifies the funtional defferences between the two. ATTENTION: Refer to the Printer Configuration unit of this manual to program the printer’s internal memory to suit individual needs using the integrated men
