Streszczenie treści zawartej na stronie nr. 1
ELECTRIC CHAINSAW
SHARPENER
Model 93213
ASSEMBLY and OPERATING
INSTRUCTIONS
NOTE: Actual product design may differ slightly from that shown in this manual.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
© ®
Copyright 2005 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or
form without the express written consent of Harbor Freight Tools.
For technical questio
Streszczenie treści zawartej na stronie nr. 2
Specifications Motor 115 V, .75A (Load), Direct Drive RPM 4200 Vise Capacity 0.80” to 0.50” Table / Vise Angles 35 Degrees Right to Left Arbor Diameter 7/8” Wheel Dimensions 4-1/4” Dia. x 1/8” Thick Overall Dimensions 9” W x 10” L x 12-1/8” H Weight 4.85 Lbs. Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the in
Streszczenie treści zawartej na stronie nr. 3
9. Maintain tools with care. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and, if damaged, have them repaired by an authorized technician. The handles must be kept clean, dry, and free from oil and grease at all times. 10. Avoid unintentional starting. Be sure the switch is in the Off position when not in use and before plugging in. 11. Stay alert. Watch what you are doing, use common
Streszczenie treści zawartej na stronie nr. 4
Additional Safety Warnings Grinding Wheel Warnings. 1. Do not use a grinding wheel if it is chipped, cracked, or worn. You can check if the wheel has cracks not visible to the human eye by hanging it up by the central hole and tapping it with a nonmetallic object (ie: screwdriver handle). If it is in good condition it will produce a metallic sound. A dull sound indicates a crack or break. 2. Only use grinding wheels that fit the Arbor (7/8”). Do not try to change or modify the mounting hole
Streszczenie treści zawartej na stronie nr. 5
Warning! Always unplug the unit before changing grinding wheels, or when making any adjustments to the Sharpener. Mounting a Grinding Wheel. Refer to the Assembly Drawing on page 10 and FIGURE 3 and FIGURE 4 below. 1. Raise the Top Housing (4B) and lock it in the up position by tightening the Lock Stop (6). 2. Remove the two screws holding the Grinding Wheel Cover (11B). Set the cover aside. 3. Unscrew the Grinder Lock Cap (9) that holds the Grinding Wheel (8) in place. 4. Install the new whee
Streszczenie treści zawartej na stronie nr. 6
Operation Warning! Always unplug the unit while adjusting chain to be sharpened. Refer to the Assembly Drawing on page 10 and the various photographs. Note: Raise the Top Housing (4B) while adjusting the chain. 1. Clean the chain before sharpening. Wash it with a nonflammable solvent. Do not use gasoline. Dry the chain. 2. Lift up the Chain Stop (23) and secure the chain in the Sliding Guides (31). See FIGURE 6. 3. Lower the Chain Stop (23) so that it is positioned on the tooth (cutter) you
Streszczenie treści zawartej na stronie nr. 7
Operation (continued) 8. Lock the chain in the Sliding Guides (31) by FIGURE 8 turning the Handle (34). See FIGURE 8. The Handle (34) should be situated so that you can easily release and tighten it. You will Limiting Gauge need to release it each time you move to the next link, and tighten it to sharpen each link. Handle (34) FIGURE 9 9. If the chain has been repeatedly sharpened, the chain depth limiting gauges may need to be taken down with a flat file (not included). See FIGURES 8 & 9. Fil
Streszczenie treści zawartej na stronie nr. 8
Operation (continued) 5. After you finished sharpening all of the teeth set FIGURE 11 for your current angle, turn off the machine by pushing the Switch (5B) and unplugging the unit. See FIGURE 11 6. Loosen the Lock Wheel (18) and reset the angle so that the first tooth that hasn’t been sharpened is positioned against the Chain Stop (23) and locked in, as explained on page 6. 7. As you did with the first half of the chain, be sure to lower the Top Housing (4B) so that the Grinding Wheel (8) ski
Streszczenie treści zawartej na stronie nr. 9
Parts List Part Description Qty. Part Description Qty. 1 Screw 3 20* Washer 1 2 Motor Cover 1 21* Bearing 1 3 Power Cord 1 22* Swing Arm 1 4B Top Housing 1 23* Chain Stop 1 5B Rocker Switch 1 24* Tension Spring 1 6 Lock Stop 1 25* Retaining Ring (5) 1 7 Grinding Wheel Base 1 26* Lower Knob 1 8 Grinding Wheel 1 27* Screw 1 9 Grinder Lock Cap 1 28* Bolt 1 10 Screw 2 29* Chain Saw Frame 1 11B Grinding Wheel Cover 1 30* Square Neck Screw 1 12 O-ring 2 31* Sliding Guide 2 13 Punching Axis 1 32* Pad 2
Streszczenie treści zawartej na stronie nr. 10
Assembly Drawing SKU 93213 For technical questions, please call 1-800-444-3353. Page 10 Chain Mounting Assembly Set 39
