Resumo do conteúdo contido na página número 1
Quick Setup Guide
(EU only)
Start Here
HL-5370DW
Before you can use the printer, read this Quick Setup Guide for the correct setup and installation.
To view the Quick Setup Guide in other languages, please visit http://solutions.brother.com/.
IMPORTANT
DO NOT connect the interface cable yet.
Unpack the printer and check the components
1
1
8
1
7
2 a Front Cover Release Button
b Control Panel
3
c Face-down Output Tray
Support Flap 1 (Support Flap 1)
4
d Front Cover
e Paper Tray
f Power Switch
g
Resumo do conteúdo contido na página número 2
Note Keep a minimum gap around the printer as shown in the illustration. 100mm(4 in.) 100mm 100mm (4 in.) (4 in.) 130mm (5.12 in.) Symbols used in this guide WARNINGS tell you what to do to prevent possible personal injury. WARNING CAUTIONS specify procedures you must follow or avoid to prevent possible minor injuries. CAUTION IMPORTANT specify procedures you must follow or avoid to prevent possible damage IMPORTANT to the printer or other objects. Electrical Hazard icons alert you to a
Resumo do conteúdo contido na página número 3
e Put the drum unit and toner cartridge assembly into the printer until it clicks into place. Install the drum unit and toner cartridge assembly 2 IMPORTANT DO NOT connect the interface cable yet. f Close the front cover of the printer. a Remove the packing tape from the outside of the printer. b Press the front cover release button and open the front cover a. 1 1 c Unpack the drum unit and toner cartridge assembly. d Gently shake it from side to side several times to distribute the to
Resumo do conteúdo contido na página número 4
c Fan the stack of paper well to avoid paper jams and misfeeds. Load paper in the paper tray 3 a Pull the paper tray completely out of the printer. d Put paper in the tray, and make sure that the paper is below the maximum paper mark a. The side to be printed on must be face down. 1 1 b While pressing the blue paper-guide release lever a, slide the paper guides to fit the paper size you are loading in the tray. Make sure that the guides are firmly in the slots. IMPORTANT Make sure the pap
Resumo do conteúdo contido na página número 5
d After the printer has finished warming up, the Status LED stops blinking and stays green. Print a test page 4 IMPORTANT DO NOT connect the interface cable yet. a Make sure that the printer power switch is off. e Press Go. The printer prints a test page. Check Connect the AC power cord to the printer. that the test page has printed correctly. b Turn on the printer power switch. Note This function will not be available after the first print job you send from your computer. Now go to c
Resumo do conteúdo contido na página número 6
6
Resumo do conteúdo contido na página número 7
® ® ® ® Macintosh Macintosh Macintosh Windows Windows Windows Windows USB Parallel Wired Network Wireless Network Choose your connection type 5 For USB interface cable ® Windows , go to page 8 Macintosh, go to page 11 For Parallel interface cable ® Windows , go to page 13 For Wired Network ® Windows , go to page 15 Macintosh, go to page 20 For Wireless Network ® Windows and Macintosh, go to page 22 7
Resumo do conteúdo contido na página número 8
® USB Windows For USB Interface Cable Users d Put the supplied CD-ROM into your CD-ROM Install the printer driver drive. The opening screen will appear and connect the printer automatically. 6 to your computer Choose your printer model and the language. IMPORTANT DO NOT connect the USB interface cable yet. Note If the Brother screen does not appear automatically, go to My Computer (Computer), Note double-click the CD-ROM icon, and then If the Found New Hardware Wizard appears on d
Resumo do conteúdo contido na página número 9
® Macintosh Windows USB ® USB Windows i When this screen appears, make sure the Note printer power switch is on. ® Connect the USB cable to the USB connector • For Windows Vista , when the User Account marked with a symbol, and then connect Control screen appears, click Continue. the cable to the computer. Click Next. • If you want to install the PS driver (Brother’s BR-Script Driver), choose Custom setup and then follow the on-screen instructions. When the Select Components screen ap
Resumo do conteúdo contido na página número 10
® USB Windows j Click Finish. Note • If you want to register your product on-line, check On-Line Registration. • If you do not want to set your printer as Default printer, uncheck Set as Default Printer. • If you want to disable the Status Monitor, uncheck Enable Status Monitor. The installation is now Finish complete. Note XML Paper Specification Printer Driver The XML Paper Specification Printer Driver is the most suitable driver when printing from the applications that use the XML Pap
Resumo do conteúdo contido na página número 11
® Macintosh Windows USB USB Macintosh For USB Interface Cable Users e Double-click the HL5300 icon on your desktop. Connect the printer to Double-click the Start Here icon. Follow the your Macintosh and on-screen instructions. 6 install the driver a Remove the label covering the USB interface connector. f Click Install Printer Driver on the menu screen. b Connect the USB cable to the USB connector marked with a symbol, and then connect the cable to your Macintosh. g Click USB cabl
Resumo do conteúdo contido na página número 12
USB Macintosh i Choose the printer you wish to connect, and then click OK. j When this screen appears, click OK. The installation is now Finish complete. 12
Resumo do conteúdo contido na página número 13
® Windows Parallel ® Parallel Windows For Parallel Interface Cable Users d Put the supplied CD-ROM into your CD-ROM Install the driver and drive. The opening screen will appear connect the printer to automatically. 6 your computer Choose your printer model and the language. IMPORTANT DO NOT connect the parallel interface cable yet. Note If the Brother screen does not appear automatically, go to My Computer (Computer), Note double-click the CD-ROM icon, and then If the Found New Har
Resumo do conteúdo contido na página número 14
® Parallel Windows f Click Parallel cable users. i Connect the parallel interface cable to your Note computer, and then connect it to your printer. ® • For Windows Vista , when the User Account Control screen appears, click Continue. • If you want to install the PS driver (Brother’s BR-Script Driver), choose Custom setup and then follow the on-screen instructions. When the Select Components screen appears, j Turn on the printer power switch. check PS (PostScript Emulation) Driver, and
Resumo do conteúdo contido na página número 15
® Macintosh Windows Wired Network ® Wired Network Windows For Wired Network Interface Cable Users d Put the supplied CD-ROM into your CD-ROM drive. The opening screen will appear For Peer-to-Peer network automatically. printer users 6 Choose your printer model and the language. 2 1 TCP/IP TCP/IP Note If the Brother screen does not appear automatically, go to My Computer (Computer), a Router double-click the CD-ROM icon, and then b Network printer double-click start.exe. Note e Click
Resumo do conteúdo contido na página número 16
® Wired Network Windows f Click Network cable users. i Choose Search the network for devices and choose from a list of discovered devices (Recommended). Or enter your printer's IP Address or its node name. Click Next. Note ® • For Windows Vista , when the User Account Control screen appears, click Continue. Note • You can find your printer’s IP Address and the node name by printing out the Printer Settings Page. See Print the Printer Settings Page on page 43. j Choose your printer, a
Resumo do conteúdo contido na página número 17
® Macintosh Windows Wired Network ® Wired Network Windows k Click Finish. Note • If you want to register your product on-line, check On-Line Registration. • If you do not want to set your printer as Default printer, uncheck Set as Default Printer. • If you want to disable the Status Monitor, uncheck Enable Status Monitor. • If you disabled your Personal Firewall software ® (e.g. Windows Firewall), turn it back on. The installation is now Finish complete. Note XML Paper Specification Printer
Resumo do conteúdo contido na página número 18
® Wired Network Windows c Click Install Printer Driver on the menu screen. For shared network printer users 6 Note Choose the Install Printer Driver icon for your 1 1 region. 3 TCP/IP 4 2 1 1 a Client computer d Click Network cable users. b Also known as “Server” or “Print server” c TCP/IP or USB or Parallel d Printer Note If you are going to connect to a shared printer on your network, we recommend that you ask your system administrator about the queue or share name for the printer pr
Resumo do conteúdo contido na página número 19
® Macintosh Windows Wired Network ® Wired Network Windows e When the License Agreement window h Click Finish. appears, click Yes if you agree to the License Agreement. Note • If you want to register your product on-line, check On-Line Registration. • If you do not want to set your printer as Default printer, uncheck Set as Default Printer. • If you want to disable the Status Monitor, uncheck Enable Status Monitor. f Choose Network Shared Printer, and then click Next. The installation is
Resumo do conteúdo contido na página número 20
Wired Network Macintosh For Wired Network Interface Cable Users e Click Install Printer Driver on the menu Connect the printer to screen. your Macintosh and 6 install the driver a Connect the network interface cable to the LAN connector marked with a symbol and then connect it to a free port on your hub. f Click Network cable users and follow the on-screen instructions. Then, restart your Macintosh. b Make sure the printer power switch is on. c Turn on your Macintosh. Put the suppl
