Resumo do conteúdo contido na página número 1
KeyMaster
- - your your codefree solution codefree solution
Installation manual
98RV1
Panasonic DVD-RV60
2000 HW-Parts HW-Parts & StoneDesign
Resumo do conteúdo contido na página número 2
1.1 - Players. These installation instructions covers the installation of the Key- Master for DVD players manufactured by: Kenwood DVD3030 Panasonic RV-20 Panasonic RV-40 Panasonic RV-60 Panasonic SA-PM08 Yamaha DVD-S796 Yamaha DVD-S796 www.stonedesign.dk/dvd/ I U K-V 2 All names, logos etc. are trademarks of their respective companies. All rights information in this document is subject to change without notice. reserved. The RV1 98
Resumo do conteúdo contido na página número 3
2.1 - Disclaimer! Read this throroughly. Before installing the KeyMaster player codefree, you should read through these warnings v We are not responsible for any illegal use of the KeyMaster. v We offer no warranty on your v The installation of the KeyMaster is at your own risk. v KeyMaster v If the manu fac tu re of the - makes chang the guara nty the fun c v The KeyMaster and it is therefore necessary to be familiar with soldering, otherwise you should get a service r to do the installation f
Resumo do conteúdo contido na página número 4
3.1 - Removal of the top cover. It is necessary to remove the frontcover of the tray. First, open the tray by pressing " OPEN " on the player or the remote control. Then, the bottom of the frontcover of the tray forward and m u l - ty fig. 1. Fig. 1 Note: The picture shows a Panasonic A160. Remember to disconnect the player from the mains before - ding. each side and three on the back of the player as shown on fig. 2. Fig. 2 The picture shows a Panasonic DVD-RV60. Note: two in topcover, Re
Resumo do conteúdo contido na página número 5
continued... To remove the mechanism, use the following procedure: Disconnect the cables connected to the frontpanel of the player. frontpanel edges. The n remove the mechanism by pulling the backside of the Note: Fig. 3 Note: The picture shows a Panasonic DVD-RV60. should be handled carefully. The mechanism is sensitive towards static electricity and mechanism upwards. Remove the four screws which holds the mechanism. Please be aware that the bottom chassis can have very sharp by
Resumo do conteúdo contido na página número 6
3.2 - Installing the KeyMaster. When the mechanism is removed it is possible to the Key- Master. fig. 4. Fig. 4 onto the bottomside of the G board . Remember to adjust the ends of the wires so they will fit onto the soldering pads. fig. 4-5-6. Do not change or remove any components. Solder the seven wires onto the board as shown on MPE attached to the mechanism). All seven wires have to be soldered board (which are MPEG Seven wires have to be soldered onto the install
Resumo do conteúdo contido na página número 7
3.2 - Continued. Fig. 5 à Connect the wire to the testp TP6209. à Connect the testp TP6201. à B ROWN wire to the testpoint TP6204 or pin 2, 3 . à Connect the W HITE wire to the testpoint TP6202 or pin 6, 3 . Fig. 6 à Connect the P 1, 3 . à Connect the G 5, IC . à Connect the 4, IC6301. wire on pin BLUE 03 63 wire on pin REY 03 IC6 wire on pin URPLE 03 IC6 03 IC6 Connect the oint wire to the BLACK oint RED
Resumo do conteúdo contido na página número 8
3.3 - Installation in the Panasonic SA-PM08. Fig. 7 à Connect the . à . à Connect the B ROWN testpoint TP6204 or 2, 3 . à Connect the W HITE TP6202 or pin 6, 3 . à Connect the GREY wire to the testpoint TP6202 or pin 5, 3 . Fig. 8 à Connect the P 1, 3 . à Connect the 4, IC6301. wire on pin BLUE 03 IC6 wire on pin URPLE 03 IC6 03 IC6 wire to the shown testpoint 03 IC6 pin wire to the shown Connect the BLACK wire to the C6501 (-) RED wire to C6501 (+) In the Panasonic SA-PM08 the installat
Resumo do conteúdo contido na página número 9
3.3 - Securing KeyMaster. fig. 9 are not located underneath the chassis of the mechanism . Fig. 9 Note: the picture shows a Panasonic DVD-RV60. Secure the KeyMaster onto the fig. 9 . Remove the protection film from the double sided tape and press the KeyMaster Fig. 10. Fig. 10 shown in In Panasonic SA-PM08 the KeyMasteren has to be sercured as thoroughly towards the chassis. as shown on mechanism chassis . Fix the wires so they cable tie. Use the cable tie as shown on Before fastening
Resumo do conteúdo contido na página número 10
3.4 - Assembling the player. Assembling the player is done using the following procedure: Ê Use the four screws to attach the mechanism. Ë Press the cables from the frontpanel into their sockets. Ì Attach the front of the player again. Then ensure all snap- locks. Put the back on and secure it. Refit the front of the tray. 3.5 - Finishing up the installation. After turning the player on and off the KeyMaster is ready for use . The player and the KeyMaster y for use . about programming th
