Resumo do conteúdo contido na página número 1
Operation
and Installation
Manual
MRC-2U
Universal Watertight Marine Radio Controller
with Speed Indicators
Resumo do conteúdo contido na página número 2
Index Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Button Locations and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 General Operations . . . . . . . . . . . . . . . . . .
Resumo do conteúdo contido na página número 3
Introduction Please carefully read all of the information in this manual. Familiarity with operation and installation proce- dures will help you obtain the best possible performance from your new Marine Radio Controller. Safety Information DO NOT OPEN COVERS AND DO NOT REPAIR BY CHANGES OR MODIFICATIONS TO THIS PRODUCT YOURSELF. PLEASE REFER SERVICING TO A NOT APPROVED BY THE MANUFACTURER WILL VOID QUALIFIED TECHNICIAN. THE WARRANTY AND WILL VIOLATE FCC APPROVAL. Button Locations and Functions 1
Resumo do conteúdo contido na página número 4
General Operations Selecting a Source/Mode: To select a play source, press the SRC button until the desired source/mode is selected. Volume: + Increase the volume by pressing the VOL button. - Increase the volume by pressing the VOL button. Increase Decrease Mute: Press the button to mute the volume level. If a CD is playing, the button will pause the disc. Press the button again to restore the volume or resume playing the disc. Tuning in a Radio Station Using Seek: Press eithe
Resumo do conteúdo contido na página número 5
Removing the Remote Removing the Remote from Holder: Release Tab Press the release tab and slide out the remote. To reinstall, slide the remote into the holder until it snaps into place. Remote Installation Connecting Strap: Inserting Strap: Pull strap until the holes line up with the corre- Insert strap through the remote holder with tabs sponding tabs to reach desired tension. facing outward. Speed-Up / Slow-Down Indicator Installation 1. Find a desired location that is clearly visible to the
Resumo do conteúdo contido na página número 6
Wiring Diagram Antenna Wire Do Not Cut or Connect Note: Receiver’s housing is not waterproof and must be mounted in a dry location. Red Wire +12 Volt Switch Black Wire Ground Infrared Emitter Attach to radio’s infrared receiver. Green LED Red LED (Speed-Up) (Slow-Down) 6
Resumo do conteúdo contido na página número 7
Learning the Radio’s Remote Code First, see if your radio is in the Manufacturer’s Code Look-Up Table below. If your radio is listed in the table go to “Automatic Code Learning”. If you can not find your radio in the list go to “Manual Code Learning”. Note: This receiver will only retain the one Radio Remote Code. Manufacturer’s Code Look-Up Table Manufacturer Group Sub-Group Radio 1 Alpine Alpine, 1 JVC, 2 JVC Pioneer 3 Pioneer 1 MobileVision and MB Quart MobileVision, 2 MB Quart, Kenwood 2 K
Resumo do conteúdo contido na página número 8
Automatic Code Learning (continued) Step 5 Step 6 or 5 Times Try each button on the remote to make sure each To exit programming push the switch on/off 5 times button has been learned properly. If the remote or wait 15 seconds and the system will automatical- does not function properly proceed to “Manual ly exit the “Automatic Code Learning” mode. Code Learning” section below. Manual Code Learning Step 1 Step 2 7 Seconds Flashes 3 Times Turn on the power to the receiver’s Press and hold the bu
Resumo do conteúdo contido na página número 9
Manual Code Learning (continued) Step 4 Flashes 2 Times Using the RF Marine Remote press the corre- The LED will flash 2 times indicating the “VOL- sponding “VOLUME UP” button to assign this UME UP” button of the radio remote has been function. programmed. The LED will then turn off and is now ready for the next button to be programmed. Step 6 Step 5 or Repeat Step 3 and 4 for the remaining 7 buttons. To exit programming push the switch on/off 3 times Each button has a unique LED flash indicato
Resumo do conteúdo contido na página número 10
Learning an Additional Aquavibe Marine Remote Controller Code The Aquavibe Marine Remote Controller is already pre-programmed to the receiver. No programming is necessary. If you want to program additional Aquavibe Marine Remote Controllers follow the instructions below. Note: This receiver will only retain the 4 Marine Remote Controller codes. If the receiver’s memory is exceeded, the receiver will start deleting transmitters codes from memory in chronological order. Step 1 Step 2 Hold Solid L
Resumo do conteúdo contido na página número 11
Clearing All the Aquavibe Marine Remote Controller Codes Step 1 Step 2 Hold Solid LED Turn on the power to the receiver’s Press and hold the button on the receiver until the LED turns housing. on solid then release button. Step 3 Press 2 Times and Hold Flashes 4 Times Push the receiver button 2 more times, holding on the last push. The LED will flash 4 times indicating that all remote codes are cleared. Step 4 Release Button LED Off Release the receiver’s button and the LED will turn off. 11
Resumo do conteúdo contido na página número 12
Warranty ONE (1) YEAR LIMITED WARRANTY Magnadyne Corporation or its authorized agents will within one year from the date of sale to you, repair, replace or refund the retail sales price of said product or any part thereof, at the option of the Magnadyne Corporation or its authorized agents, if said product or part is found defective in materials or workmanship, when properly connected and operating on the correct power requirements designated for the specific product. This warranty and Magnadyne
