Resumo do conteúdo contido na página número 1
Model PRO-800
Owner’s Manual
Remote Security System
with Dual Stage Shock Sensor
IMPORTANT ! In order to provide the highest possible level of security to your vehicle, this
system is equipped with selectable manual override circuitry. It is possible that you will need
to manually override your security system if the transmitter becomes lost, or inoperative due
to battery failure. Reading the sections on "MANUALLY OVERRIDING YOUR SYSTEM" is
necessary to fully understand the procedure required
Resumo do conteúdo contido na página número 2
YOUR “ Code Hopping “ TRANSMITTERS The transmitters included with your new security system use the most advanced and secure form of radio frequency transmission available on any current automotive security system. Some of today’s sophisticated auto thieves use a device known as a code grabber, which will receive and store the signal from your keychain transmitter, and retransmit at a later time to disarm your system. Your code hopping transmitters will change their signal every time the button i
Resumo do conteúdo contido na página número 3
The Triggered LED Indicates: Whenever the system is armed and then triggered from either entry point or any additional sensor device, the triggered LED will flash 15 times, and the hand held transceiver will play a melody. Note: Upon trigger, the hand held unit can be selected to vibrate, play a melody, or both. See details below. Two Way Transmitter Operation: The two way transmitter depicted in this manual operates similar to any transmitter with the exception that it will also indicate that t
Resumo do conteúdo contido na página número 4
Check Vehicle Status: Press the lock+key+option buttons simultaneously for 1 second. The vehicle's alarm will display the systems current status breifly by flashing the LED associ- ated with the state the vehicle was left in. This feature is useful if you do not want to wait the 10 seconds for a LED to display the status or if you just want to check the status without operating the Lock or Unlock buttons. ARMING THE SYSTEM - ACTIVE 1. Turn off the engine, exit the vehicle and close all doors,
Resumo do conteúdo contido na página número 5
arming cycle will restart when all doors are closed. At the end of the passive arming cycle; Dash mounted LED begins to flash slowly. Parking Lights flash one time. Siren sounds one chirp If the siren did not sound when arming, then the chirps have been turned off, and you should refer to the section titled "ELIMINATING THE ARM / DISARM CHIRPS" in this manual. Doors Lock - Optional Door locking during passive arming is a selectable feature. The alarm can be programmed to allow the doors
Resumo do conteúdo contido na página número 6
Siren sounds two chirps. If the siren sounds 4 chirps, then the alarm was triggered in your absence. Before turning the key on, examine the LED and refer to the INTRUSION WARNING SIGNALS section of this manual to iden- tify which zone was triggered. If the siren did not sound when disarming, then the chirps have been turned off, and you should refer to the section titled “ELIMI- NATING THE ARM / DISARM CHIRPS“ in this manual. Doors Unlock - Optional Note: If the optional 2 step door unlock c
Resumo do conteúdo contido na página número 7
INTRUSION WARNING SIGNALS This system will inform you if an intrusion attempt has occurred while you were away from the vehicle. If an intrusion attempt has occurred, the siren will chirp 4 times and the parking lights will flash 3 times when disarming the system. Enter the vehicle and observe the dash mounted LED to identify which zone was trig- gered. If the LED is flashing one time...pause...one time...pause...etc., then an intrusion attempt was made to the shock sensor, or an accessory tr
Resumo do conteúdo contido na página número 8
Programming Your Custom Override Code: Unlike override switches easily found, and defeated, this security system allows the consumer to program a personal override code, offering a higher level of security. To take advantage of this option, programmable feature # 10 must be selected for the Custom Code Option. Consult your installation center for programming details. The system comes from the factory with a pre-programmed override code of 11. To change this default override code, do the foll
Resumo do conteúdo contido na página número 9
8. Turn the ignition switch to the off position. Immediately observe the LED flash pattern. You will note the LED flashing five times, pause, and then flash two times, pause. This pattern will be repeated three times indicating the new code (52) has been accepted and stored in memory. NOTE: If after step 8, the LED flashes a code other than what was just entered, this indicates that the code has not been changed. You will have to repeat steps 1 through 7 above being certain to note the followi
Resumo do conteúdo contido na página número 10
1. Press and hold the ARM or DISARM button on the keychain transmitter for 3 or more seconds. The alarm will immediately sound. 2. To stop the alarm, press and hold the ARM or DISARM button on the transmitter again for 3 seconds. If the button is not pressed, the alarm will automatically stop after 30 seconds. Also if any transmitter button other than the ARM or DISARM button is pressed and released, the Panic mode will be turned off immediately. The normal function of this transmitter button
Resumo do conteúdo contido na página número 11
ADDITIONAL REMOTE FUNCTION ( CHANNEL 5 ) This security system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are; Remote Trunk Release Remote Car Starter Remote Window Closure Remote Garage Door Interface To activate the optional accessory, press the programmed button on the keychain transmitter for up to 8 seconds for continuous output, or press and release for momentary activation. The optiona
Resumo do conteúdo contido na página número 12
PRO-800 SYSTEM FUNCTIONS AT A GLANCE DASH LED INDICATORS RAPID FLASHING = PASSIVE ARMING SLOW FLASHING = ARMED OFF = DISARMED ON SOLID = VALET MODE 3 FLASH...PAUSE = INTRUSION ZONE 3 2 FLASH...PAUSE = INTRUSION ZONE 2 1 FLASH...PAUSE = INTRUSION ZONE 1 SIREN CHIRP INDICATORS *1 CHIRP = ARM *2 CHIRPS = DISARM 3 CHIRPS = ARM / DOOR OPENED 4 CHIRPS = DISARM / INTRUSION * These chirps are optional, and can be de - activated. PARKING LAMP INDICATORS 1 FLASH = ARM 2 FLASHES = DISARM 3 FLASHES = DISA
