Manual do usuário Harbor Freight Tools 96406

Resumo do conteúdo contido na página número 1

LeveLing scissor jack
5,000 Lb. capacity
Model 96406
operation instructions
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
visit our website at: http://www.harborfreight.com
t o prevent serious injury, read and understand
aLL warnings and instructions before use.
© ®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of this manual
or any artwork contained herein may b

Resumo do conteúdo contido na página número 2

specifications Jack Construction 10 Gauge Sheet Steel Plate Crank Handle Construction Steel Rod Rubber Grip and Attached Socket and Dimensions 25-3/4” L X 15/32” Diameter (5” Long Rubber Handle and Grip) Jack Capacity 5000 lb. maximum capacity with height not less than 13-3/4” Lift Range 4-5/8” Minimum Height to 23-1/2” Maximum Height Overall Dimensions 26-1/4” Total Length X 4-5/8” High X 6-3/4” Wide (Collapsed for Storage) Bolt-On (see directions on page 5 of this manual) Jack Mounting Weld-O

Resumo do conteúdo contido na página número 3

9. use the right tool for the job. There are certain applications for which this Level- ing Scissor Jack was designed. It will do the job better and more safely at the rate for which it was intended. Do not modify this Jack and do not use this Jack for a purpose for which it was not intended. 10. dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Wear restrictive hair covering to contain long hair. 11. do not overreach. Keep proper footing and bal

Resumo do conteúdo contido na página número 4

23. do not use this leveling scissor jack for aircraft purposes. 24. some rv sub-frames are not capable of handling any additional forces beyond its intended design strength to support the cabin weight. c ontact your rv manu- facturer for the sub-frame strength information before use of this scissor jack. 25. the warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. it must be understood by the operator

Resumo do conteúdo contido na página número 5

boL t -on instaLLation 1. warning! before driLLing HoLes, cHeck for any cHassis coMpo - nents wHicH May be inside tHe fraMe. Look for eLectricaL Lines and wires, gas tank, gas Lines, water and HoLding tanks, genera - tor fueL Lines and water Heater Lines. Make sure area is cLear of tHese coMponents before driLLing. 2. Hold the Jack against the frame and using the Mounting Brackets (9) as a template, mark the locations of the 8 mounting holes on the RV or Trailer frame. Remove the Jack. 3

Resumo do conteúdo contido na página número 6

2. Using Handle (16) lower Jacks on opposite sides for stabilization (see steps 3 and 4 in previous section). note: If motor home comes with factory installed hydraulic levelers, the Leveling Scissor Jack can be used to provide additional stabilization. Follow the directions for installation found in this manual on pages 4 and 5. Maintenance 1. Before use, inspect the Leveling Scissor Jack for cracks, dirt or debris in threads, loose welds or bolts and anything else that looks or feels abn

Resumo do conteúdo contido na página número 7

parts List and diagraM part description Q’ty part description Q’ty part description Q’ty 1 Base 1 7 Axis w/out Thread 1 13 Retaining Ring 4 2 Lower Lifting Arm 2 8 Upper Fixing Frame 1 14 Bearing 1 3 Lower Fixing Frame 1 9 Mounting Brackets 2 15 R-Clip 1 4 Screw Rod 1 10 Upper Lifting Arm 2 16 Handle Wrench 1 5 Axis with Thread 1 11 Hex Bolt M10 X 70 2 17 Hex Bolt M10 X 80 2 6 Flat Washer 16 2 12 Lock Nut M10 4 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED