Resumo do conteúdo contido na página número 1
RoyalTek
BT GPS Speed Camera Warning Device
RCD-3000
(Utility Offline version)
Users Manual
Version 0.1
English 1
Resumo do conteúdo contido na página número 2
Content 1.Product Introduction .........................................................................................................................3 1.1 Overview................................................................................................................................3 1.2 Check the Package Content....................................................................................................3 1.3 Install RCD-3000 in your vehicle ...............................
Resumo do conteúdo contido na página número 3
1.Product Introduction 1.Product Introduction 1.1 Overview Congratulations on your purchase of the BT GPS Camera warning device. The Device is equipped with the latest generation SiRF Star III digital processor specially designed for fast and accurate fix on GPS signals. The RCD-3000 will help you to drive safely, when the database has been downloaded, the device will compare your position using its built-in GPS antenna with the position of every known danger locations
Resumo do conteúdo contido na página número 4
1.3 Install RCD-3000 in your vehicle (A) Volume Control (C) Power Button (B) Mini USB Port (A) Volume control: Rotate forward and backward to adjust the volume. (B) Mini USB port: Connect with the USB Cable for data transfer or battery charging purpose. (C) Power Button: Power ON / Power OFF Place the Dashboard Pad on your dashboard as close to the windscreen as possible in clear view of the driver’s line of sight. Place your RCD-3000 device on the dashboard pad, which is desi
Resumo do conteúdo contido na página número 5
1.5 Navigation Function via BT To make RCD-3000 Receiver work with your devices, a simple pairing step is required for the first time. (Please follow the pairing instruction for Blue Tooth from your PDA or PC manufacturer.) To get RCD-3000 into pairing mode, all you need to do is simply switch on the power switch. Once RCD-3000 is properly set up and connected to your PDA or PC, please refer to your navigation software guidebook for instruction on navigation o
Resumo do conteúdo contido na página número 6
2.Specification 2.Specification 2.1 Specification GPS GPS Chipset - Sirf Star III - L1, 1,575.42 MHz Frequency Channel - 20 parallel C/A Code - 1,023 MHz Fix time - Reacquisition: less than 1s (Open SKY,typical) - Hot start: less than 1s - Warm start: less than 35s - Cold start: less than 35s Accuracy - Position: within 10m for 90% - Velocity: 0.1m/s Interface Protocol - Output message: NMEA 0183 ver. 3.0,GGA, GSA, RMC and GSV every 1s, - Baud rate 57,600bps Dynamics Alti
Resumo do conteúdo contido na página número 7
2.2 LED Display & Audio Alarm Front View Event LED Display Audio Alarm 1 GPS outage Green LED, Blinking X 2 GPS fixed Green LED, Glowing 2 beeps Approach Certified Fix Not exceed Red LED Glowing 3 beeps 3 Camera Zone and pre-alert speed (distance less than* 1500 meter- Notification range) Over speed Blinking 2 beeps in every 3 seconds Approach Certified Fix Not exceed Red LED Glowing 3 beeps 4 Camera Zone and pre-alert speed (distance less than *500 Over speed Blinking Beeps
Resumo do conteúdo contido na página número 8
3.Software Installation and Usage 3.Software Installation and Usage 3.1 Start to use “Speed Camera Detector Utility” Check the COM port of RCD-3000 first. Click “Start” “Control Panel” ”Performance and Maintenance” “System”, and you will see the System Properties dialog box; click on “Hardware” tab and then the “Device Manager” button. Expand the “Ports (COM & LPT)” item, and the “Prolific USB-to-Serial Comm Port” is the COM port of your RCD-3000. The user should connect the device
Resumo do conteúdo contido na página número 9
Figure2 Figure3 Figure 4 is shown System will download the POI points from device automatically. POI data will be erased from device after POI load process done. English 9
Resumo do conteúdo contido na página número 10
Figure 4 If the figure 5 dialog is shown, it means there is no POI data in the device. Figure 5 3.2 POI Management Procedure When proceed the POI Management, system will auto create the POI folder for POI data download. Note:POI data are stored in the PC side and named POI.csv and stored in the subdirectory /POI/. User can load POI data, delete POI data or Save POI data by using the Utility. Note: English 10
Resumo do conteúdo contido na página número 11
◆Load POI: User can edit the POI points by click the button ”Load POIs”. There are 5 types of status will show on the Utility screen after loading POI action is done. *Duplicated with No. X: means the distance between the current POI point and No. X POI point less than 1km. *Out of SCDB range: means the current POI point is not in the SCDB coverage range. *OK: means the valid POI point. *Speed is out of range: means the POI’s speed is over the spec " the speed range is from 0 to 300km/
Resumo do conteúdo contido na página número 12
Figure 7 Figure 8 shows the Delete POIs process. Figure 8 3.2.1 POI Management and shown on Map To display the POIs on Google Map, the Internet connection is needed. Move the mouse cursor to the required “Latitude” or “Longitude“ point column then press the English 12
Resumo do conteúdo contido na página número 13
mouse right key, the message “Go to Google Map” showed as Figure 9 Figure 9 3.2.2 POI data modification User can modify the speed, latitude, and longitude and add comments. 1) Modification of the latitude and longitude: When user clicks the “Go to Google Map” pop up menu, user can modify latitude and longitude, the utility will show as Figure 10. User can drag the mark to set the position of the POI on Google Map window. After the modification is complete, please press the button “O
Resumo do conteúdo contido na página número 14
2) Modification of the comments and speed: Check the “comments” or “speed” column of POI then user can add the comments or speed on it, shows as Figure 10 After the modification is complete, please press the button “Save POIs” Note:Users can add comments for the POI and only 255 words can be added.. Speed range is from 0~300km/hr. Figure 8 English 14
Resumo do conteúdo contido na página número 15
3.3 SCDB and POI import setting ◆SCDB Setting : There is one type Camera database data. Fixed Speed Camera database data User can download the Speed Camera database from his computer (local file). For the Speed camera database file format, please reference the example: File name: *.csv Latitude, Longitude, direction, vmax, Type 46.55886,2.2,35.40,2 ◆POI Setting : Note: The function will be enabled after the Save POI action was done by user. User can integrate the POI data into SC
Resumo do conteúdo contido na página número 16
Figure12 Press the button “Go to Connection Page” and the AP will go to the “connection” page. System will show the notification message. Shows as Figure 13 and 14 Figure13 Figure14 Figure 15 shows that the upload proceed. English 16
Resumo do conteúdo contido na página número 17
Figure15 Figure 16 shows that the download process is completed. And system will auto alert you to do the action ”RESRT and Reconnect the device” after the upload process was completed. Please re-connect the device. Figure16 3.3.2 POI Setting process Go to the page “SCDB and POI import setting”, user should check the checkbox “SCDB setting” to choose the SCDB at the same time, then press the button “Go to connection Page’, .The utility will go to page “Connection” and integrate S
Resumo do conteúdo contido na página número 18
3.4 Datalog download and device configure Function User can download log data by using the Utility. Figure 17 shows: Change to “Device Config.” menu bar. Figure 17 Figure 18 shows: select Folder or set a new folder for saving NMEAData. Figure 18 Figure 19 Show: Change page to “Data Log Download” menu bar and the AP will go to the page “Data Log Download”. Figure 19 3.5 Get and Set RCD-3000 Data Log Status User can review the RCD-3000 default setting configuration. Engl
Resumo do conteúdo contido na página número 19
Figure 20 shows: Change to “Data Log Status” menu bar Figure 20 ◆Time Interval (user adjustable) It means the time distance between the record two positions Default setting is 15secs 1sec ~ 60secs, user adjustable ◆Data Type (user adjustable) There are 3 options for user to choose these data items to be saved in the RCD-3000. 1: UTC Time, Longitude, Latitude, will be saved. 2: UTC Time, Longitude, Latitude, Altitude, will be saved. 3: UTC Time, Longitude, Latitude, Altit
Resumo do conteúdo contido na página número 20
LED to see if the flash is full. ◆Set Log Config. When user finished the configuration setup, press the “Set Log Config.” button to save the setting to the receiver. ◆Memory Erase User can erase all the log data from the device. 3.6 SCDB Setting Change to “SCDB Setting” menu bar ◆Speed Camera Alert Setting : User can set the Critical Range value and Notification range of the device. Note: Notification range should be bigger than Critical range 200m. English
