Resumo do conteúdo contido na página número 1
®
IOP19 Series
Integral Color Camera/Lens for
SB1900 Series Dome
Installation/Operation Manual
C718M (10/96)
Pelco • 3500 Pelco Way, Clovis, CA 93612-5699 • (1-209) 292-1981 • (800) 289-9100
FAX (800) 289-9150 or (1-209) 292-3827
Resumo do conteúdo contido na página número 2
(This page intentionally left blank.) iv PELCO Manual C718M-(10/96)
Resumo do conteúdo contido na página número 3
TABLE OF CONTENTS Section Page 1.0 WARNINGS ........................................................................................................................................1 2.0 SCOPE ...............................................................................................................................................2 3.0 DESCRIPTION ...................................................................................................................................2 3.1 MODELS ...
Resumo do conteúdo contido na página número 4
LIST OF ILLUSTRATIONS Figure Page 1 IOP Package Installation..............................................................................................................2 2 Wiring Diagram for SB1900 Dome and IOP Package .................................................................3 3 Back Focus Adjustment ...............................................................................................................4 4 Camera Adjustments ......................................................
Resumo do conteúdo contido na página número 5
IOP19 SERIES INTEGRAL COLOR CAMERA/LENS PACKAGE FOR SB1900 SERIES DOMES 1.0 WARNINGS 3. Only use replacement parts recommended by Prior to installation and use of this product, the follow- Pelco. ing WARNINGS should be observed. 4. After replacement/repair of this unit’s electrical 1. Installation and servicing should only be done by components, conduct a resistance measurement Qualified Service Personnel and conform to all between line and exposed parts to verify the ex- Local codes. posed par
Resumo do conteúdo contido na página número 6
4.0 INSTALLATION 2.0 SCOPE To install the camera/lens package in your dome, fol- This manual covers the IOP19 Series of integral color low the steps below. camera/lens packages. 1. Disconnect main power to the back box. 3.0 DESCRIPTION 2. Remove the dome drive from the back box. Pelco's IOP19 Series of integral color camera/lens com- binations are specifically designed for use in the SB1900 3. Refer to Figure 1. Remove the nuts and flat wash- Series of indoor surveillance dome enclosures. ers
Resumo do conteúdo contido na página número 7
Figure 2. Wiring Diagram for SB1900 Dome and IOP Package Pelco Manual C718M (10/96) 3
Resumo do conteúdo contido na página número 8
➤ White Balance 5.0 ADJUSTMENTS White balance has two positions; one is ATW (Au- tomatic Tracing White), which is a feature that Your optics package comes from the factory adjusted continuously adjusts the camera for optimum color for a broad range of lighting conditions. For this rea- reproduction. AWB (Automatic White Balance) is son, you may find it necessary to adjust your optics a feature that retains current settings in memory package to tailor the picture to your specific viewing even wh
Resumo do conteúdo contido na página número 9
5.2 SHUTTER SPEED 5.3 AUTO GAIN CONTROL This optics package is provided with adjustable shutter Refer to Figure 4. The AGC control setting should be speeds. This feature allows minimal streaking when a set and left in the ON position. very fast moving object passes in front of the non- moving optics package. The shutter speed is factory set to 1/60 second. You can select one of eight shutter speeds (refer to Figure 4). SHUTTER SPEED ADJUSTMENTS MAY BE PERFORMED BY USING A SMALL STANDARD SCREWD
Resumo do conteúdo contido na página número 10
5.4 WHITE BALANCE (ATW/AWB SWITCH) In the ATW (Automatic Tracing White Balance) posi- tion, the white balance is continuously adjusted to take into account variations in the incident light conditions. In the AWB (Automatic White Balance) position, when the LOCK button is pressed, the white balance is auto- matically adjusted, and the setting is stored in memory. When the switch is set to this position the white bal- ance always takes the previously stored value. White balance is factory set to
Resumo do conteúdo contido na página número 11
6.0 WIRING DIAGRAM Figure 5. Wiring Diagram for Color Camera/Lens Pelco Manual C718M (10/96) 7
Resumo do conteúdo contido na página número 12
7.0 EXPLODED ASSEMBLY DRAWING—TVH6 Figure 6. TVH6 Camera/Lens Combination Exploded Assembly Drawing 7.1 MECHANICAL PARTS LIST (Figure 6) Item Qty Description Part Number 11 Lens, 1/2", 6X motorized zoom, F1.2, 8.5-51 mm H6Z851M 21 Frame, 6X lens package JIOP084307COMP 3 Not used 41 Clamp, wire fatigue 80010016 51 Top cover JIOP084106COMP 61 Back cover JIOP084108COMP 71 Camera, Sony, 1/2", high resolution, color (NTSC) SC-CPL27 81 Circuit board, IOP camera interconnect PCB8500200ASSY A Not use
Resumo do conteúdo contido na página número 13
8.0 EXPLODED ASSEMBLY DRAWING—TVH10 Figure 7. TVH10 Camera/Lens Combination Exploded Assembly Drawing 8.1 MECHANICAL PARTS LIST (Figure 7) Item Qty Description Part Number 11 Lens, 1/2", 10X motorized zoom, F1.2, 8-80 mm H10Z880M 21 Frame, 10X lens package JIOP194504COMP 3 Not used 41 Clamp, wire fatigue 80010016 51 Top cover JIOP084103COMP 61 Back cover JIOP084105COMP 71 Camera, Sony, 1/2", high resolution, color (NTSC) SC-CPL27 81 Circuit board, IOP camera interconnect PCB8500200ASSY A Not u
Resumo do conteúdo contido na página número 14
9.0 SPECIFICATIONS ELECTRICAL MECHANICAL Color NTSC (EIA) Camera Module Mounting Bracket Input Voltage: 24 VAC, 60 Hz Construction: 0.050" aluminum Power Requirements: Less than 5 watts Dimensions: See Figures 8 and 9 Video Output: 1 V p–p composite video into 75 ohms Operating Temperature: 14° to 131°F (-10° to 55°C) Imaging Device: 1/2" CCD Illumination: 2.5 LUX @ F1.2 Scanning System: 525 lines, interlaced/60 Hz Horizontal Resolution: 470 TVL Shutter Speed: Adjustable, 1/60 to 1/10,000 secon
Resumo do conteúdo contido na página número 15
10.0 WARRANTY AND RETURN INFORMATION WARRANTY RETURNS Pelco will repair or replace, without charge, any merchandise proved In order to expedite parts returned to the factory for repair or credit, please defective in material or workmanship for a period of one year after the date call the factory at (800) 289-9100 or (559) 292-1981 to obtain an of shipment. authorization number (CA number if returned for credit, and RA number if returned for repair). Exceptions to this warranty are as noted below
Resumo do conteúdo contido na página número 16
Pelco 300 West Pontiac Way Clovis, CA 93612-5699 (209) 292-1981 • (800) 289-9100 FAX (800) 289-9150 or (209) 292-3827 • DataFAX (800) 289-9108 or (209) 292-0435 International customers call 1-209-292-1981 or FAX 1-209-348-1120 (Product specifications subject to change without notice.) C718M
