Resumo do conteúdo contido na página número 1
Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
Otreap Or ’s Mlauna
Push Mower — Model 10M
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Printed In USA Form No. 769-03690
(November 27, 2007)
Resumo do conteúdo contido na página número 2
To The Owner 1 Thank You Thank you for purchasing a Lawn Mower manufactured by Cub This product has met the rigid safety standards of the Outdoor Cadet LLC. It was carefully engineered to provide excellent Power Equipment Institute and an independent testing performance when properly operated and maintained. laboratory. If you have any problems or questions concerning the machine, phone your local Cub Cadet dealer or contact us Please read this entire manual prior to operating the equipment
Resumo do conteúdo contido na página número 3
Important Safe Operation Practices 2 WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol. HEED ITS WARNING! CALIFORNIA PROPOSITION 65 WARNING: Engine Exhaust, some of its constituents, and certain v
Resumo do conteúdo contido na página número 4
12. A missing or damaged discharge cover can cause blade 27. When starting engine, pull cord slowly until resistance contact or thrown object injuries. is felt, then pull rapidly. Rapid retraction of starter cord (kickback) will pull hand and arm toward engine faster than 13. Many injuries occur as a result of the mower being pulled you can let go. Broken bones, fractures, bruises or sprains over the foot during a fall caused by slipping or tripping. could result. Do not hold on to the mow
Resumo do conteúdo contido na página número 5
3. Check the blade and engine mounting bolts at frequent Service intervals for proper tightness. Also, visually inspect blade for damage (e.g., bent, cracked, worn) Replace blade with Safe Handling Of Gasoline: the original equipment manufacture’s (O.E.M.) blade only, 1. To avoid personal injury or property damage use extreme listed in this manual. “Use of parts which do not meet the care in handling gasoline. Gasoline is extremely flammable original equipment specifications may lead to i
Resumo do conteúdo contido na página número 6
Spark Arrestor Average Useful Life According to the Consumer Products Safety Commission WARNING: This machine is equipped with an (CPSC) and the U.S. Environmental Protection Agency (EPA), internal combustion engine and should not be used this product has an Average Useful Life of seven (7) years, or 140 on or near any unimproved forest-covered, brush hours of operation. At the end of the Average Useful Life, buy covered or grass-covered land unless the engine’s a new machine or have the
Resumo do conteúdo contido na página número 7
Fold along dotted line (represents a 15° slope) Sight and hold this level with a vertical tree... or a corner of a building... or a fence post 15° Use this page as a guide to determine slopes where you may not operate safely. WARNING: Do not operate your lawn mower on such slopes. Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A riding mower could overturn and cause serious injury. Operate riding mowers up and down slopes, neve
Resumo do conteúdo contido na página número 8
Assembly & Set-Up 3 Contents of Carton • One Lawn Mower • One Lawn Mower Operator’s Manual • One Bottle of Oil • One Side Discharge Chute 2. Locate the hairpin clip on the weld pin on each side of Assembly lower handle. NOTE: This unit is shipped without gasoline or oil in the engine. a. Remove hairpin clip from this hole. Using a pair of Fill up gasoline and oil as instructed in the accompanying engine pliers, insert hairpin clip into the hole on pin closest manual BEFORE operating your mo
Resumo do conteúdo contido na página número 9
3. The rope guide is attached to the right side of the upper Side Discharge Chute handle. See Fig. 3-3. Loosen the wing nut which secures the Your mower is shipped as a mulcher. To convert to side rope guide. discharge: 1. Lift the mulching plug. See Figure 3-5. A 1 2 B D C Figure 3-3 a. Hold blade control against upper handle. Figure 3-5 b. Pull starter rope out of the engine. Release blade 2. Slide two hooks of side discharge chute under hinge pin on control. mulching plug assembly. Lower
Resumo do conteúdo contido na página número 10
Adjustments Set-Up Cutting Height Gas and Oil Fill-Up Each wheel has a height adjustment lever to change the cutting Refer to the Engine Operation section in this manual for height of the mower. additional engine information. 1. Depress height adjustment lever towards wheel. 1. Add oil provided before starting unit for the first time out of the box. 2. Slide lever to desired position for a change in cutting height. See Fig. 3-6. 2. Service the engine with gasoline as instructed in the Engine
Resumo do conteúdo contido na página número 11
Controls and Features 4 Blade Control Choke Control Recoil Starter Cutting Height Adjustment Lever (one at each wheel) Side Discharge Chute Mulch Plug Figure 4-1 Side Discharge Chute Blade Control Your mower is shipped as a mulcher. To discharge the grass The blade control is attached to the upper handle of the mower. clippings to the side instead, follow the instructions in the Depress and squeeze it against the upper handle to operate the Assembly & Set-Up section to attach the side di
Resumo do conteúdo contido na página número 12
Operation 5 Starting Engine WARNING: Be sure no one other than the operator is standing near the lawn mower while starting engine or operating mower. Never run engine indoors or in enclosed, poorly ventilated areas. 2 Engine exhaust contains carbon monoxide, an odorless and deadly gas. Keep hands, feet, hair and loose clothing away from any moving parts on engine and lawn mower. 1. Pull out the choke knob located on the left side of the upper handle. See Fig. 5-1. 4 NOTE: Use of the chok
Resumo do conteúdo contido na página número 13
Maintenance & Adjustments 6 2. Lubricate the wheels at least once a season with light oil (or Maintenance motor oil). If wheels are removed for any reason, lubricate surface of the pivot arm and inner surface of the wheel General Recommendations with light oil. See Fig. 6-1. • Always observe safety rules when performing any 3. Lubricate the torsion spring and pivot points on the side maintenance. mulch plug periodically with light oil to prevent rust. See • The warranty on this lawn mower
Resumo do conteúdo contido na página número 14
Service 7 WARNING: An unbalanced blade will cause Blade Care excessive vibration when rotating at high speeds. It WARNING: When removing the cutting blade for may cause damage to mower and could break sharpening or replacement, protect your hands with causing personal injury. a pair of heavy gloves or use a heavy rag to hold the 5. Lubricate the engine crankshaft and the inner surface of blade. the blade adapter with light oil. Slide the blade adapter Periodically inspect the blade adapt
Resumo do conteúdo contido na página número 15
Troubleshooting 8 Problem Cause Remedy Engine Fails to start 1. Blade control disengaged. 1. Engage blade control. 2. Spark plug boot disconnected. 2. Connect wire to spark boot. 3. Fuel tank empty or stale fuel. 3. Fill tank with clean, fresh gasoline. 4. Engine not primed (if equipped with primer). 4. Prime engine as instructed in the Operation section. 5. Faulty spark plug. 5. Clean, adjust gap, or replace. 6. Blocked fuel line. 6. Clean fuel line. 7. Engine flooded. 7. Wait a few minutes to
Resumo do conteúdo contido na página número 16
Engine Operation 9 Fuel Cap Air Cleaner Starter Grip Oil Fill Cap Oil Drain Spark Plug Figure 10-1 Pre-Operation Check 10w Oil Recommendations NOTE: This engine is shipped without gasoline or oil in the 20w engine. Running the engine with insufficient oil can cause serious engine damage and void the engine warranty. 1 20 • Before starting engine, fill with oil. Do not over-fill. Oil capacity is about 20 oz. 30 Use a 4-stroke, or an equivalent high detergent, premium 40 quality motor oil ce
Resumo do conteúdo contido na página número 17
Check Oil Level Check Fuel Level NOTE: Be sure to check the engine on a level surface with the 1. Clean around fuel fill before removing cap to fuel. engine stopped. 2. Fill tank to approximately 1-inch below lowest portion of 1. Remove the oil filler cap and wipe the dipstick clean. See neck to allow for fuel expansion. Be careful not to overfill. Fig. 10-2. NOTE: Before refueling, allow engine to cool 2 minutes. Starting The Engine WARNING: Always keep hands and feet clear of equipment movin
Resumo do conteúdo contido na página número 18
Engine Maintenance 10 Periodic inspection and adjustment of the engine is essential WARNING: Shut off the engine before performing if high level performance is to be maintained. Regular any maintenance. To prevent accidental start-up, maintenance will also ensure a long service life. The required disconnect the spark plug boot. service intervals and the kind of maintenance to be performed are described in the table below. Follow the hourly or calendar IMPORTANT: If engine must be tipped t
Resumo do conteúdo contido na página número 19
Oil Service Air Cleaner Service • Check oil level regularly. Paper filters cannot be cleaned and must be replaced once a year or every 100 operating hours; more often if used in extremely • Be sure correct oil level is maintained. Check every five dusty conditions. hours or daily before starting engine. See oil checking procedure in the Operation section. WARNING: Never use gasoline or low flash point solvents for cleaning the air cleaner element. A fire Oil Change or explosion could resul
Resumo do conteúdo contido na página número 20
3. Measure the plug gap with a feeler gauge. Correct as Spark Plug Service necessary by bending side electrode. See Fig. 10-4. The gap should be set to 0.030 in. WARNING: DO NOT check for spark with spark plug removed. DO NOT crank engine with spark plug removed. To ensure proper engine operation, the spark plug must be properly gapped and free of deposits. 1. Remove the spark plug boot and use a spark plug wrench Electrode to remove the plug. See Fig. 10-3. Spark Plug 0.030 in. Figure 10-
