Resumo do conteúdo contido na página número 1
Safety Instructions & Operator’s Manual for
21” STEEL DECK
WALK MOWERS
SERIES 15
PUSH
MODELS
216015
216515BV
MODEL NUMBER EXPLANATION
21 65 15 BV
CUTTING WIDTH ENGINE DESIGNATION
ENGINE HORSE POWER SERIES DESIGNATION
21 – 21” Cutting Width B – Briggs &Stratton 15 - Series Designation
60 – 6.0 HP (Engine Horse Power) V – Overhead Valve 65 – 6.5 HP (Engine Horse Power)
Thank you for buying a SNAPPER Product! Before operating your Walk Behind
Resumo do conteúdo contido na página número 2
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must understand these instructions and must allow only persons who understand these instructions to operate machine. Each person operating the machine must be of sound mind
Resumo do conteúdo contido na página número 3
IMPORTANT SAFETY INSTRUCTIONS OPERATION MAINTENANCE AND STORAGE 1. DO NOT put hands or feet near or under rotating 1. DO NOT store mower or fuel container inside parts. Keep clear of discharge area while engine where fumes may reach an open flame, spark or is running. pilot light such as in a water heater, furnace, 2. STOP engine when crossing gravel drives, clothes dryer or other gas appliance. Allow walks, or roads, and under any conditions engine to cool before storing machine in a
Resumo do conteúdo contido na página número 4
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS.............................................2 & 3 TABLE OF CONTENTS ............................................................................ 4 SECTION 1 - FAMILIARIZATION.............................................................. 5 SECTION 2 - OPERATING INSTRUCTIONS......................................... 6-8 Pre-start Checklist...............................................................................................6 S
Resumo do conteúdo contido na página número 5
Section 1 - FAMILIARIZATION FIGURE 1.1 1.1 INTRODUCTION 1.2 NOMENCLATURE This manual has been prepared for the operators of The nomenclature drawing above, Figure 1.1, shows the SNAPPER WALK BEHIND MOWERS. Its the essential parts of the SNAPPER WALK BEHIND purpose, aside from recommending operating and MOWERS. It is recommended that all operators of routine service requirements, is to promote s
Resumo do conteúdo contido na página número 6
Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST 2.1.6. Clean exterior surfaces of cutting deck and Make the following checks and perform the service engine of any accumulation of spilled fuel, dirt, grass, required before each start-up. oil, etc. Keep engine air intake screen and cooling 2.1.1. Check guards, deflectors, grass bag, adapter fins clear at all times. and covers to make sure all are in place and securely tightened. 2.2 STARTING & OPERATION 2.2.1. ENGINE & BLADE
Resumo do conteúdo contido na página número 7
Section 2 - OPERATING INSTRUCTIONS 2.5 CUTTING HEIGHT ADJUSTMENT 2.3 STOPPING 1. Pull the height adjusting latch outward and move Stop engine and blade by releasing the blade to desired cutting height. See Figure 2.5. control. Stop forward motion of mower by releasing the wheel drive control. LOWEST CUTTING 1 2.4 HANDLE HEIGHT ADJUSTMENT LATCH HEIGHT The height of the mower handle can be adjusted as follows: 1. Loosen the lower nuts on each lower handle as shown in Figu
Resumo do conteúdo contido na página número 8
Section 2 - OPERATING INSTRUCTIONS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all MIDDLE components to cool. HANDLE CROSS BAR ATTACH BAG HOOKS 2.6 RECYCLING OPERATION OVER MIDDLE HANDLE CROSS BAR (Optional Accessory) NOTE: For best recycling results, cut up to a m
Resumo do conteúdo contido na página número 9
Section 3 – MAINTENANCE 3.1 INTRODUCTION RECOMMENDED To retain the quality of the mower, use genuine BLADE RETAINING CAP SCREW SNAPPER replacement parts only. Contact a local TORQUE VALUE SNAPPER dealer for parts and service assistance. SHOULD BE 30 TO For the correct part or information for a particular 40 FT. LBS. mower, always mention model and serial number. 3.2 SERVICE - AFTER FIRST 5 HOURS 3.2.1. CHANGE ENGINE OIL WARNING DO NOT attempt any maintenance, adjustments o
Resumo do conteúdo contido na página número 10
Section 4 - REPAIR & ADJUSTMENTS 2. Replace the blade if it is badly chipped, bent, WARNING noticeably out of balance or has cracks or notch in DO NOT attempt any maintenance, adjustments or either tip. See Figure 4.1 & 4.2. Replace with new service with engine and blade running. STOP engine blade. and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all WARNING components to cool. Wear
Resumo do conteúdo contido na página número 11
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury. 4. Sharpen blade on
Resumo do conteúdo contido na página número 12
TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Engine Will Not Start 1. Fuel tank empty. 1. Fill fuel tank with fresh fuel. Using Recoil Starter 2. Engine needs choking or priming. 2. Choke/Prime. Check Engine Manual for Instructions. 3. Spark plug wire disconnected. 3. Place spark plug wire onto spark plug. Engine Stalls or Stops 1. Blade control is released or is not being held securely 1. Blade control should be held securely against After Running against handle. handle a
Resumo do conteúdo contido na página número 13
SERVICE SCHEDULE ITEM SERVICE PERFORMED REF. EACH 5 25 50 100 EACH USE HRS HRS HRS HRS SEASON Engine Oil Check Oil Level Page 6 X Initial Oil Change Page 9 X Periodic Oil Change Page 9 X* Air Pre-Cleaner Clean Sponge Element Engine Manual X** & Page 9. Clean or Replace Engine Manual. Air Cleaner X** Spark Plug Replace Engine Manual. X Engine Cooling Clean Shroud & Fins Engine Manual X** System Mower Blade Check For Wear, Damage Page 10-11 X
Resumo do conteúdo contido na página número 14
3 YEAR LIMITED WARRANTY For three (3) years from purchase date for the original purchaser's residential, non-commercial use, SNAPPER, through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both. For ninety (90) days from purchase date for the original purchaser's commercial, rental, or other non-residential use, S
Resumo do conteúdo contido na página número 15
PRIMARY MAINTENANCE 15
Resumo do conteúdo contido na página número 16
PRIMARY MAINTENANCE 16
Resumo do conteúdo contido na página número 17
PRIMARY MAINTENANCE 17
Resumo do conteúdo contido na página número 18
PRIMARY MAINTENANCE 18
Resumo do conteúdo contido na página número 19
NOTES ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ __________
Resumo do conteúdo contido na página número 20
Safety Instructions & Operator’s Manual for 21” STEEL DECK WALK BEHIND MOWERS SERIES 15 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments. If you have any
