Resumo do conteúdo contido na página número 1
54Mbps PoE Access Point
WAP-4033PE
User’s Manual
Resumo do conteúdo contido na página número 2
Copyright Copyright © 2006 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET. PLANET makes no representations or warranties, either expressed or implied, with respect to the contents hereo
Resumo do conteúdo contido na página número 3
interference received, including interference that may cause undesired operation. Federal Communication Commission (FCC) Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation. R&TTE Compliance Statement This equipment complies with all
Resumo do conteúdo contido na página número 4
Revision User’s Manual for PLANET 54Mbps PoE Access Point Model: WAP-4033PE Rev: 1.0 (Oct, 2006) Part No. EM-WAP4033PE 4
Resumo do conteúdo contido na página número 5
TABLE OF CONTENTS Chapter 1 Introduction ..................................................................................7 1.1 Package Contents.................................................................................................... 7 1.2 System Requirements.............................................................................................. 7 1.3 Features ..................................................................................................................
Resumo do conteúdo contido na página número 6
Chapter 4 Specification ...............................................................................36 Chapter 5 Frequently Ask Question ...........................................................37 6
Resumo do conteúdo contido na página número 7
Chapter 1 Introduction Thank you for purchasing WAP-4033PE. The WAP-4033PE supports both IEEE 802.11b and IEEE 802.11g standards. You can use it to connect an existing WLAN, or to build up a new wireless LAN. Except for essential AP mode, WAP-4033PE also provides AP Client/ Bridge/ Repeater and WDS (Wireless Distributed System) modes to accommodate all kinds of network topology. High data rate (up to 54Mbps) support allows faster communication between LAN and WLAN. Maximize network effici
Resumo do conteúdo contido na página número 8
1.3 Features Complies with the IEEE 802.11b/g (DSSS) 2.4GHz specification Supports 2.400~2.4835 GHz frequency band Data rate supports up to 54Mbps IEEE 802.3af compliant Auto rate fallback in case of obstacles or interferences Supports WEP/WPA-PSK/WPA/WPA2 encryption Supports AP/ AP Client/ Bridge/ Repeater and WDS (Wireless Distributed System) mode Seamlessly integrate wireless and wired Ethernet LAN networks Provides MAC Filter function Built-in DHCP server Support Auto
Resumo do conteúdo contido na página número 9
microwave ovens, heavy-duty motors, fluorescent lights and other industrial equipments. Keep the number of walls or ceilings between AP and clients as few as possible. Otherwise the signal strength may be seriously reduced. Place WAP-4033PE in a open space or add additional WAP-4033PE as needed to improve the coverage. 2. Environmental factors The wireless network is easily affected by many environment factors. Every environment is unique with different obstacles, construction materials,
Resumo do conteúdo contido na página número 10
Chapter 2 Hardware Installation Before you proceed with the installation, it is necessary that you have enough information about the WAP-4033PE. 1. Locate an optimum location for the WAP-4033PE. The best place for your WAP-4033PE is usually at the center of your wireless network, with line of sight to all of your mobile stations. 2. Assemble the antenna to WAP-4033PE. Try to place them to a position that can best cover your wireless network. The antenna’s position will enhance the recei
Resumo do conteúdo contido na página número 11
Chapter 3 Web Configuration Web configuration provides a user-friendly graphical user interface (web pages) to manage your WAP-4033PE. An AP with an assigned IP address (e.g. http://192.168.0.1) will allow you to monitor and configure (via web browser e.g., MS Internet Explorer or Netscape). 1. Open your web browser. 2. Enter WAP-4033PE IP address (default IP address is http://192.168.0.1) into the address field of the web browser. Please also make sure your PC’s IP address is in the same
Resumo do conteúdo contido na página número 12
3.2 Basic Setting In this option, you can configure WAP-4033PE to work to different operating mode. Please refer to below sections to know the details configuration of each operating mode. 3.2.1 AP Mode This mode is set to WAP-4033PE by default. It served as a transparent Media Access Control (MAC) bridge between wired and wireless network. 12
Resumo do conteúdo contido na página número 13
Parameter Description Mode Shows the current operation mode. You may set WAP-4033PE to other operating mode by select other operating mode. Band 2.4GHz (B): It allows to select the transmit rate up to 11Mbps. 2.4GHz (G): It allows to select the transmit rate up to 54Mbps. 2.4GHz (B+G): It provides best performance for 11g transmission when you enable the AP mode selection to “Mixed mode”. SSID The SSID (up to 32 printable ASCII characters) is the unique name identified in a WLAN. The ID
Resumo do conteúdo contido na página número 14
work. You may check the LED status to make sure WAP-4033PE is finish the restart. 3.2.2 Station - Ad Hoc Mode Served as a wireless station (Ad-hoc). Connected to a PC or a small LAN, this station along with other wireless stations can establish a small wireless network without Access Points. 14
Resumo do conteúdo contido na página número 15
Parameter Description Mode Shows the current operation mode. You may set WAP-4033PE to other operating mode by select other operating mode. Band 2.4GHz (B): It allows to select the transmit rate up to 11Mbps. 2.4GHz (G): It allows to select the transmit rate up to 54Mbps. 2.4GHz (B+G): It provides best performance for 11g transmission when you enable the AP mode selection to “Mixed mode”. SSID Please make sure the SSID of the wireless network that you will connected and enter the corre
Resumo do conteúdo contido na página número 16
3.2.3 Station - Infrastructure Mode Served as a wireless station (infrastructure). Connected to a PC or a small LAN, it allows the PC or small LAN able to access the wireless network via Access Point. Parameter Description Mode Shows the current operation mode. You may set WAP-4033PE to other operating mode by select other operating mode. Band 2.4GHz (B): It allows to select the transmit rate up to 11Mbps. 2.4GHz (G): It allows to select the transmit rate up to 54Mbps. 2.4GHz (B+G)
Resumo do conteúdo contido na página número 17
3.2.4 AP Bridge - Point to Point Mode This function provides to bridge for 2 wired Ethernet networks to connect to each other by wireless. You can use two WAP-4030s in this mode to connect two wired Ethernet networks together. Parameter Description Mode Shows the current operation mode. You may set WAP-4033PE to other operating mode by select other operating mode. Band 2.4GHz (B): It allows to select the transmit rate up to 11Mbps. 2.4GHz (G): It allows to select the transmit rate
Resumo do conteúdo contido na página número 18
to configure the detail settings. After configuration complete, please click “Apply” button to save the configuration. Then you will see a screen to prompt you the settings are save successfully. You may press “Continue” for configure other settings or “Apply” to restart WAP-4033PE with new configuration. 3.2.5 AP Bridge - Point to Multipoint Mode This function provides to bridge more than 2 wired Ethernet networks together by wireless connection. You can use more than two WAP-4033PE
Resumo do conteúdo contido na página número 19
AP MAC Address If you want to bridge more than two wired Ethernet networks together with wireless connection, you have to enter the MAC addresses of otherWAP-4033PEs that with join the bridging work into the fields. Set Security IF you want to enable security to protect your wireless connection. Please press “Set Security” button and refer to section “3.2.8 Security setting for bridge mode” to configure the detail settings. After configuration complete, please click “Apply” button to save
Resumo do conteúdo contido na página número 20
Band 2.4GHz (B): It allows to select the transmit rate up to 11Mbps. 2.4GHz (G): It allows to select the transmit rate up to 54Mbps. 2.4GHz (B+G): It provides best performance for 11g transmission when you enable the AP mode selection to “Mixed mode”. SSID The SSID (up to 32 printable ASCII characters) is the unique name identified in a WLAN. The ID prevents the unintentional merging of two co-located WLANs. Please make sure that the SSID of all stations in the same WLAN network are the s
